Question about 2004 Cadillac SRX
SOUNDS LIKE VAULT OR WRONG BULB IN BRAKE LAMP SOCKET. STARTER SHOULDN'T HAVE CAUSED PROBLEM
Posted on Dec 29, 2013
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
wow i feel sorry for you because Cadillac designed this bulb to be a don't get to bulb but OK here's what you do take the bottom cover off or skid plastic panel under neath the front end theirs little plastic clips holding it on just get come dikes and don't cut them but just use it to help pull them out. after you get that off use a flash light and locate your light housing you should see two screws holding the house in i think those screws are 8mm i cant remember remove those two screws and be careful the metal from the bumper cuts you pull the light housing out and remove all the screws around the housing and open the housing up replace the bulb and make sure your contact to the bulbs clean and then reassemble the way you took apart. if you cant get it well then best bet is take it somewhere i know Cadillac charges an arm and a leg so you can go somewhere else.
Posted on Jan 25, 2009
You would be better off going to a Cadillac Dealership and paying the diagnostic fee. Spend $65 to find out what the real problem is rather than replacing parts until the car runs properly. This way you get it from a Cadillac Technician. Once you know what the problem is you can decide on where you want to have it service. Because you are paying for the diagnostics you shouldn't feel obligated to have it done at a Dealership. Please leave me good feedback if you feel this has helped.
Posted on Jul 09, 2009
If you go to the auto parts store they should have a fuel line disconnect tool that has a 5/16ths end an a 3/8ths end. The tool is shaped like an X. Before you start you need to pull the fuel pump fuse under the front of the REAR passenger side seat while the car is running and let it stall. it will release the built up pressure. This is important unless you want gas to spray every where. Then take the tool and start with the end of the filter with two lines. Place the appropriate end of the tool over the smallest inlet, push the tool in then pull the line towards the filter and then push the line away and it should disconnect. Do the same with line above. Then you can use the two appropriate size wrenches to disconnect the outlet end. reconnecting the new filter is simple just make sure your quick connect lines click in all the way and you tighten the outlet line well, I think its like 22 or 25 ft/lbs.
Posted on Dec 15, 2009
SOURCE: Are you suppose to use
Really, you need to use what the manual reccomends, in your case that should be premium. While you will usually not suffer damage from using lower grade, you will suffer performance and economy loss.
Posted on Oct 27, 2010
Tips for a great answer:
Jun 12, 2017 | Cadillac Cars & Trucks
Jun 07, 2015 | 2004 Cadillac SRX
Sep 14, 2013 | 2004 Cadillac SRX
Mar 04, 2013 | 2004 Cadillac SRX
Feb 07, 2013 | 2004 Cadillac SRX
Oct 02, 2012 | 2004 Cadillac SRX
Jan 21, 2011 | 2007 Cadillac SRX
Nov 30, 2009 | 2004 Cadillac SRX
Mar 26, 2009 | 2004 Cadillac SRX
Jun 07, 2017 | Cadillac SRX Cars & Trucks
122 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: