Question about 2001 Hyundai Trajet

Open Question

Rough noise when driving over 50 km - 2001 Hyundai Trajet

Posted by on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What type of spark plug will i use NGK BKR5E-11 or BKR6E-11? i usually travel 8 km and 8 km back with speed of 50 km


Both the spark plugs are the same. The only difference between the two is the heat range number. BKR5E-11 is the hotter plug and BKR6E-11 is the medium hot plug which offers better heat of dissipation. . Better to go for the BKR6E-11. It can be used safely for both local drive and as well as for the long drive.

May 29, 2015 | Cars & Trucks

1 Answer

Micra K13 Loud Noise at Higher Speeds


I've just bought a K13 Nissan Micra and it doesn't sound quite right. The noise I hear also seems to be coming from the back but it sounds like when you chop down a gear in a manual going down a hill and the engine revvs, well this is the noise I get in the automatic speeding up and slowing down, even just cruising at a steady speed. Any ideas people? Apart from this noise I love this car.

Aug 20, 2012 | Nissan Cars & Trucks

1 Answer

2004 Mazda MPV makes loud sound when driving faster than about 60 km/hr


There is no way to estimate cost until you know the exact case of the noise. See the dealer for a test drive so a tech can listen to it.

Jun 26, 2012 | 2004 Mazda MPV

1 Answer

We just replaced our univeral joints and both front bearings and rotors believing that this was the cause of the howling and grinding sound, plus we changed our tires to eliminate that as a cause of the...


you didn't say what kind of truck it was but that sounds like it could be a carrier bearing or a bad drive shaft, if the drive shaft has ANY dents or dings it won't be balanced.

Jan 26, 2011 | Chevrolet Avalanche Cars & Trucks

1 Answer

Obd2 system rediness status won't clear so I can run the smog test due to replacing the battery.


takes a long time to run the rediness test since there are 6 different tests to complete...

PROCEDURE 1
EVAPORATIVE EMISSION SYSTEM LEAK MONITOR
Inspection Conditions
Engine coolant temperature: 30°C (75°F) or less (The engine is stopped before the test drive is started).
Atmospheric temperature: 5 - 30°C (41 - 113°F).
Condition of A/T: Selector lever D range.
Fuel remained in fuel tank: 30 - 50% is recommended.
Time required: 16 minutes or less after started the engine.
Drive cycle pattern: One trip monitor (from start to ignition switch to "LOCK" (OFF) position. Well be completed while traveling with the following drive cycle pattern.
Test Procedure
Engine: start.
Accelerate until the vehicle speed is 89 km/h (55 mph) or more.
While keeping the accelerator pedal opening degree constant, keep the vehicle speed at 89 km/h (55 mph) or more and travel for 16 minutes.
Return the vehicle to the shop, then turn the ignition switch to "LOCK" (OFF) position.

PROCEDURE 2
FUEL TRIM MONITOR
Drive Cycle Pattern
Inspection Conditions
Engine coolant temperature: 100°C (212°F) or less.
Atmospheric temperature: -10 - 60°C (14 - 140°F).
Condition of A/T: Selector lever D range.
Time required: 30 minutes or more.
Drive cycle pattern: One trip monitor (from start to ignition switch to "LOCK" (OFF) position). Will be completed while traveling with the following drive cycle pattern.
Test Procedure
Engine: start.
Accelerate until the vehicle speed is 89 km/h (55 mph) or more.
While keeping the accelerator pedal opening degree constant, keep the vehicle speed at 89 km/h (55 mph) or more and travel for 30 minutes.
Return the vehicle to the shop, then turn the ignition switch to "LOCK" (OFF) position

PROCEDURE 3
CATALYTIC CONVERTER MONITOR
Drive Cycle Pattern
Inspection Conditions
Atmospheric temperature: -10°C (14°F) or more.
Condition of A/T: Selector lever D range.
Engine coolant temperature: Not set.
Time required: 16 minutes or more.
Drive cycle pattern: One trip monitor (from start to ignition switch to "LOCK" (OFF) position). Will be completed while traveling with the following drive cycle pattern.
Test Procedure
Engine: start.
Accelerate until the vehicle speed is 89 km/h (55 mph) or more.
Travel for 300 seconds or more while keeping the vehicle speed at 89 km/h (55 mph) or more.
Decelerate until the vehicle speed is within 80 km/h (50 mph) or less.
While traveling at 56 - 80 km/h (35 - 50 mph) for 10 minutes or more, fully close the throttle at least once in 2 minutes and decelerate for 10 seconds or more.
Do not repeat deceleration too often.
Vehicle speed may go below 56 km/h (35 mph) after the deceleration.
Stopping and braking are permitted. (If stopped or drive at 56 km/h (35 mph) or less for more than 5 minutes the monitoring may be stopped. In this case please restart monitoring from the beginning.)
After completing the above deceleration, bring the vehicle speed back to 56 - 80 km/h (35 - 50 mph) and keep it in the range until starting the deceleration again.
Repeat the above deceleration at least 5 times.
Return the vehicle to the shop, then turn the ignition switch to "LOCK" (OFF) position

PROCEDURE 4
HEATED OXYGEN SENSOR MONITOR
Drive Cycle Pattern
Inspection Conditions
Engine coolant temperature: 100°C (212°F) or more.
Atmospheric temperature: -10°C - 60°C (14 - 140°F) or more.
Condition of A/T: Selector lever D range.
Time required: 16 minutes or more.
Drive cycle pattern: One trip monitor (from start to ignition switch to "LOCK" (OFF) position). Will be completed while traveling with the following drive cycle pattern.
Test Procedure
Engine: start.
Accelerate until the vehicle speed is 56 - 80 km/h (35 - 50 mph).
While keeping the accelerator pedal opening degree constant, keep the vehicle speed at 56 - 80 km/h (35 - 50 mph) and travel for 16 minutes or more.
Stopping and braking during this operation are permitted. Keep the accelerator opening degree constant for 1 minute or more after each acceleration.
Return the vehicle to the shop, then turn the ignition switch to "LOCK" (OFF) position

PROCEDURE 5
EXHAUST GAS RECIRCULATION (EGR) SYSTEM MONITOR
Drive Cycle Pattern
Inspection Conditions
Engine coolant temperature: 100°C (212°F) or less.
Atmospheric temperature: 5 - 60°C (41 - 140°F).
A/C switch: OFF.
Condition of A/T: Selector lever D range.
Time required: 16 minutes or more.
Drive cycle pattern: One trip monitor (from start to ignition switch to "LOCK" (OFF) position). Will be completed while traveling with the following drive cycle pattern.
Test Procedure
Engine: start.
Accelerate until the vehicle speed is 56 - 80 km/h (35 - 50 mph).
While traveling 16 minutes or more at 56 - 80 km/h (35 - 50 mph) with engine speed 2,000 r/min or above, fully close the throttle at decelerate for 5 seconds or more until the engine speed reaches 1,000 r/min or under.
Do not repeat deceleration too often.
Stopping and braking are permitted (Rapid deceleration and sharp steering are not permitted).
After completing the deceleration, bring the vehicle speed back to 56 - 80 km/h (35 - 50 mph) and keep it in the range until starting the deceleration again.
Repeat the above deceleration at least 8 times by fully closing the throttle valve.
Return the vehicle to the shop, then turn the ignition switch to "LOCK" (OFF) position

PROCEDURE 6
OTHER MONITOR (Main Components, Sensors & Switches, Wire Breakage & Short Circuit)
Drive Cycle Pattern
Inspection Conditions
Engine coolant temperature:
100°C (212°F) or less (Except engine coolant temperature sensor monitoring).
30°C (86°F) or less (Engine coolant temperature sensor monitoring).
Atmospheric temperature:
5°C (41°F) or more (Except engine coolant temperature sensor monitoring).
-10°C (14°F) or less (Engine coolant temperature sensor monitoring).
Condition of A/T: Selector lever D range.
Time required: 21 minutes or more.
Drive cycle pattern: One trip monitor (from start to ignition switch to "LOCK" (OFF) position). Will be completed while traveling with the following drive cycle pattern.
Test Procedure
Engine: start
Accelerate until the vehicle speed is 56 km/h (35 mph) or more.
While keeping the accelerator pedal opening degree constant, keep the vehicle speed at 56 km/h (35 mph) or more and travel for 16 minutes or more.
Return the vehicle to the shop.
After stopping the vehicle, continue idling for 5 minutes, and then turn the ignition switch to the "LOCK" (OFF) position. Moreover, the vehicle should be set to the following conditions for idling.
A/C switch: OFF
Lights and all accessories: OFF
Transmission: Neutral

Sep 15, 2010 | 1998 Mitsubishi Eclipse

2 Answers

2003 Mitsubishi Galant ES Clunking noise


the first thing i would check is the sway bar bushings they usualy go first. you have a bushing out somwhere. ive replace many struts because people have requested new struts and when we install them they come back and complain that the clunk is still there and all it needed was a bushing kit for $20
hope this helps

Aug 24, 2008 | 2003 Mitsubishi Galant

Not finding what you are looking for?
2001 Hyundai Trajet Logo

Related Topics:

25 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

75005 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7710 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...