Question about Cars & Trucks

Open Question


Posted by Anonymous on


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

My parking light went out, I changed it and it burned where the bulb was plugged in and a little around it. Just worried that its faulty wiring and my car catchig fire. What to do?

Dome light or running light?
The lights outside the car have almost no chance of creating a fire.
The scorching on the bulb socket is common with the newer wedge base bulbs. Sometimes the socket gets so bad that the the plastic crumbles and has to be replaced.



Sep 06, 2016 | Cars & Trucks

1 Answer

Why do i get rattle from beldray electric fire ?

A rattle from an electrical appliance indicates a loose electrical component The vibration is caused by the cycles of the power in use. (hum from a fluro light) have an accredited electrician check it out as it may be serious.

Nov 17, 2014 | Cars & Trucks

1 Answer

My beldray steamer water won't heat or steam red light on then blue nothing happens where am I going wrong

Steam outlet could be calcified, (need cleaning) happens if you don't use purified water.

Sep 30, 2014 | Cars & Trucks

1 Answer

Changing the brake light lamp/bulb

the plastic posts are guides /support they just slide into place attached to lens just slide/pull the lens off

Jun 18, 2017 | 1995 Toyota Corolla

1 Answer

How do you remove the headlight assembly on 1995 ford f250?

  • 1.
    Remove the two upper screws from the headlight housing, using a Phillips screwdriver.
  • .
    Locate the two lower retaining nuts inside the engine compartment at the bottom of the headlight housing. Remove the nuts using a ratchet, extension and socket.
  • Separate the turn signal and marker light assembly from the front grill. Rotate the bulb holders counterclockwise and pull them out of the assembly. Set the assembly aside.
  • Unplug the headlight bulb connector from the bulb. Rotate the retaining ring counterclockwise one-eighth turn and remove it from the housing. Pull the headlight bulb straight back and out of the housing. Do not rotate the bulb during disassembly.
  • Lift up on the headlight housing retaining clips to unsnap them from the headlight housing vertical adjuster studs.
  • Locate the horizontal adjuster at the outer bottom corner of the headlight assembly inside the engine compartment. Loosen the horizontal adjuster until it is free of the adjuster nut.
  • Remove the headlight housing from the vehicle.
  • Install the headlight housing in the front grill.
  • Engage the horizontal adjuster screw with the adjuster nut and screw it partially in.
  • Snap the headlight housing clips on the vertical headlight adjuster studs.
  • Insert the headlight bulb into the headlight housing, flat side up. Slightly rotate the headlight bulb to engage the grooves in the light with the alignment tabs in the back of the housing. Install the retaining ring on the bulb. Plug in the headlight bulb connector.
  • Install the bulb holders in the turn signal and marker light assembly. Install the assembly in the grill. Install the two upper screws, using a Phillips screwdriver. Install the two lower retaining nuts, using a ratchet, extension and socket.
Headlight Aiming
  • Pull the vehicle to within a few inches of a blank wall, on a flat surface. Apply two strips of tape to the wall vertically to mark the centers of the headlights. Apply a strip of tape to the wall horizontally to mark the center of the headlight height. Back the vehicle up 25 feet in a straight line.
  • Turn the headlight low beams to the "On" position.
  • Adjust the vertical headlight adjusters until the high-intensity zone of the light pattern is two inches below the horizontal mark on the wall.
  • Adjust the horizontal headlight adjusters until the high-intensity zone of the light pattern is two inches to the right of the vertical headlight marks on the wall.

Nov 08, 2012 | Cars & Trucks

1 Answer

How to change a light bulb in a plugin color disco ball

There's no need for such trouble. You just need to change a disco light. Then Iotton Disco Ball Light is most best choice, which has 3 sound activated modes and 7 modes stage light.
This disco party light change the color automatically, also can be changed under the music rhythm.
Fully adjustable speed,when it at a slow speed, it can give you a smooth projection on the ceiling or on the wall to create a romantic, relaxed and beautiful atmosphere of colorful lights. Enjoy the crazy with your friends under the great music effects.

Jun 20, 2012 | Cars & Trucks

1 Answer

Back light for the odometer on my 1999 Sun fire is out. How do you replace the bulb.

is this the digital odometer? unfortunately, there is no bulb to change if so. you must have the whole IPC replaced at a GM dealer.

Nov 28, 2009 | 1999 Pontiac Sunfire

1 Answer

Where is the headlight relay switch

The relay switch is below the engine, on the wall between the engine and the driver. This is a common problem with the J's.

Jan 20, 2009 | 1997 Infiniti.5 J30

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

76 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts


Level 3 Expert

80263 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

john h

Level 3 Expert

15139 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides