Question about 2010 Volvo V50 1.6D

Open Question

Fuel filter problems new filter fitted\no starting

Posted by Anonymous on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to troubleshoot a no fuel problem, no fuel at fuel rail in a 2000 olds sillhouette.


First check there is battery voltage to the pump and the pump starts when the ignition is switched on , if not check fuse and relay, check wiring from relay to pump. If ok and the pump is working , check for fuel blockage from the tank inlet to the pump , some have a sock type filter in the tank pick up tube, if all ok remove the fuel filter , switch on and fuel should flow at the filter, fit a new filter, if still no fuel at the rail fit a fuel pressure gauge an check for low pressure , if ok, the fuel pressure regulator may be stuck causing a air lock replace it.

Apr 15, 2015 | 2000 Oldsmobile Silhouette

1 Answer

Fuel pressure


have a pressure test done on the fuel manifold to check for pressure regulator , filter and pump. Run fault codes to check for injectors and coils faults

Nov 22, 2013 | Audi A4 Cars & Trucks

1 Answer

Fitting fuel filter car cant start


there is air in the filter.there chould be bolt you can untight.
and a pump on the filter to pump out the air.then tighten the bolt again

Apr 28, 2013 | Cars & Trucks

1 Answer

How to change the fuel filter on saturn 1994 sw?


first relieve the fuel pressure at the schrader valve. Use small plastic tool supplied with new filter to disconnect filter hose fitting at the fuel rail. Squeeze the tabs on the fitting and disconnect the fuel line from the filter, then remove the nuts and detach the filter. push the new disconnect fitting onto the new filter and lubricate both filter fittings weth clean engine oil. Install filter into bracket and puch the quick connect fitting onto the filter and fuel line, making sure they snap securely into place.

Oct 16, 2011 | 1996 Saturn SW

1 Answer

How to change a fuel filter on a 1994 mercury sable


this is for a 3.8 GS the fuel filter is located near the right rear tire


RELIEVING FUEL SYSTEM PRESSURE

  1. open the trunk. on the driver side pull back the carpet and you find the fuel cut switch. take your open hand and slap the side of the switch. it should pop up. now get in the car ans start it and run it till it stops. when it dies try to start once more.


REMOVAL & INSTALLATION

  1. Disconnect the negative battery cable.
  2. Remove the push connect fittings at both ends of the fuel filter. This is accomplished by removing the hairpin clips from the fittings. Remove the hairpin clips by first bending, and then breaking the shipping tabs on the clips. Spread the 2 clip legs approximately 1 / 8 in. (3mm) to disengage the body and push the legs into the fitting. Gently pull on the triangular end of the clip and work it clear of the fitting.
  3. Remove the filter from the mounting bracket by loosening the worm gear mounting clamp enough to allow the filter to pass through
  4. detach lines from fuel filter. move small bucket or whatever to catch what left in lines ( filter will still have gas in it)
  5. Install the new filter in the mounting bracket, ensuring that the flow direction arrow is pointing forward. Locate the fuel filter against the tab at the lower end of the bracket.
  6. Insert a new hairpin clip into any 2 adjacent openings on each push connect fitting, with the triangular portion of the clip pointing away from the fitting opening. Install the clip to fully engage the body of the fitting. This is indicated by the legs of the hairpin clip being locked on the outside of the fitting body. Apply a light coat of engine oil to the ends of the fuel filter, then push the fittings onto the ends of the filter. When the fittings are engaged, a definite click will be heard. Pull on the fittings to ensure that they are fully engaged.
  7. Tighten the worm gear mounting clamp to 15-25 inch lbs. (1.7-2.8 Nm)
  8. open the trunk again and push the button on the fuel switch down and reconnect the battery and start the engine and check for leaks


tar171.jpg

Dec 17, 2010 | 1994 Mercury Sable

1 Answer

Where is the fuel filter in a 1992 Cadillac Deville CP?


Generally, GM products from this era have an external canister type fuel filter near the gas tank underneath the car by the rear axle.

The following illustrates the proper procedure for changing:

REMOVAL & INSTALLATION CAUTION
Never smoke when working around gasoline! Avoid all sources of sparks or ignition. Gasoline vapors are EXTREMELY volatile! WARNING
Fuel supply lines on all vehicles equipped with fuel injected engines will remain pressurized for long periods after engine shutdown. The pressure must be relieved before servicing these fuel systems.
  1. Disconnect the negative battery cable.
  2. Depressurize the fuel system.
  3. Remove the filter bracket retainer.
  4. For plastic type fittings:
    1. Grasp the filter and one fuel line fitting. Twist the quick connect fitting 1⁄4 turn in each direction to loosen any dirt within the fitting. Repeat for the other fuel line fitting.
    2. Squeeze the plastic retainer release tabs and pull the connection apart. Repeat for the other fitting.
  5. For metal type fittings:
    1. Use a fuel pipe quick-connect separator J37088 or equivalent. This is available from your local parts store.
    2. Insert the tool into the female side of the connector, then push inward to release locking tabs. Pull the connection apart. Fig. 1: There are a couple of fasteners that need to be removed to access the filter. This is one of them 91041p71.jpg
      Fig. 2: Some models utilize a plastic fitting on the fuel filter 91041p74.jpg
      Fig. 3: Twist the fuel line back and forth while holding the filter still. This will loosen any dirt caught in the connection 91041p75.jpg
      Fig. 4: Squeeze the tabs on the plastic line to free them from the lock 91041p76.jpg
      Fig. 5: Slide the hose off the front end of the filter first. It's easier to work with 91041p77.jpg
      Fig. 6: Remove the other fitting in the same manner 91041p78.jpg
      Fig. 7: After removing the fuel line from the other side, you can now slide it out of the sleeve and remove it from the vehicle 91041p73.jpg
      Fig. 8: The filter is typically attached to this bracket 91041p72.jpg
      Fig. 9: Remove the filter from this bracket before installing the new filter 91041p69.jpg
      To install:
  6. Remove the protective caps from the new filter and apply a few drops of clean engine oil to both tube ends of the filter and O-rings. Install the fuel filter so that the flow arrow follows the direction of fuel flow.
  7. Install the new plastic connector retainers onto the filter inlet and outlet tubes (plastic collar type fittings).
  8. Push the connectors together to cause the retaining tabs to snap into place. Once installed pull on both ends of each connection to make sure they are secure.
  9. Before installing the fitting on the filter, wipe the filter end with a clean cloth. Inspect the inside of the fitting to make sure it is free of dirt and/or obstructions
  10. Align the fitting, and filter axially and push the fitting onto the filter end. Pull on the fitting to make sure it is fully engaged.
  11. Install the fuel filter and bracket on the frame.
  12. Connect the negative battery cable.
  13. Start the engine and check for leaks.

Jun 08, 2010 | 1992 Cadillac DeVille

1 Answer

Replace fuel filter


  1. Relieve the fuel system pressure. For details regarding this procedure, please refer to Section 5 of this manual.
  2. If not done already, disconnect the negative battery cable.
  3. Raise and safely support the vehicle.
  4. Clean both fuel feed pipe connections and the surrounding areas at the in-line fuel filter with a clean rag to avoid possible contamination of the fuel system.
  5. Using a backup wrench, remove the fuel line fittings from the fuel filter.
  6. Either separate the quick-connect fittings or remove the fuel filter mounting screws, then slide the fuel filter out of the mounting bracket.
  7. Discard the fuel line O-rings and replace with new ones during installation.
To install:
  1. Install new O-rings to the fuel line fittings.
  2. Connect the fuel lines to the fuel filter.
  3. Position the filter in the mounting bracket, in the same position it was during removal. Using a backup wrench, tighten the fuel lines to 16 ft. lbs. (22 Nm).
  4. Install the fuel filter mounting screws.
  5. Carefully lower the vehicle. Install or tighten the fuel filler cap.
  6. Connect the negative battery cable.
  7. Start the engine and check for leaks.
25d7525.gif
Location of the fuel filter

9f0ac98.gif
Unfasten the retaining bracket can make removal of the fuel filter easier

2c6ca73.gif
Either use a clean rag or compressed air to clean the surrounding areas of the filter

523254f.gif
Use a backup wrench to disconnect the fuel line fittings from the filter

2e1fdd8.gif
Disengage the quick-connect fittings, then remove the filter from the vehicle

0d20d1f.gif
In-line fuel filter mounting and related components

It sits in front of the fuel tank.

Dec 07, 2009 | 1992 Buick Riviera

1 Answer

1998 diesel freelader is pinking


You have a leak somewhere that is letting the fuel system **** in air. This is serious and needs to be taken care of immediately. Check all your lines and fittings for wet spots or signs of fuel leaking and repair. Also double check to make sure your new filter is on tight and no fittings have been put on crossthreaded. Hope this helps.

Nov 01, 2009 | Land Rover Freelander Cars & Trucks

2 Answers

Air in fuel


The metal pipes out from the tank rust drop it down and you will see the holes or put fuel hose right over them .

Jun 16, 2009 | 1999 Isuzu Trooper

2 Answers

Changing fuel filter on 2002 Mazda pickup


Clean all dirt and/or grease from the fuel filter fittings. "Quick Connect" fittings are used on models equipped with a pressurized fuel system. These fittings must be disconnected using the proper procedure or the fittings may be damaged. The fuel filter uses a "hairpin" clip retainer. Spread the two hairpin clip legs about 1/8 in. (3mm) each to disengage it from the fitting, then pull the clip outward. Use finger pressure only; do not use any tools. Push the quick connect fittings onto the filter ends. Mazda recommends that the retaining clips be replaced whenever removed. The fuel tubes used on these fuel systems are manufactured in 5/16 in. and 3/8 in. diameters. Each fuel tube takes a different size hairpin clip, so keep this in mind when purchasing new clips. A click will be heard when the hairpin clip snaps into its proper position. Pull on the lines with moderate pressure to ensure proper connection. Start the engine and check for fuel leaks. If the inertia switch (reset switch) was disconnected to relieve the fuel system pressure, cycle the ignition switch from the OFF to ON position several times to re-charge the fuel system before attempting to start the engine.
0900c15280192eed.jpgRemove the "hairpin" clip retainers to access the fuel line fittingsThe inline reservoir type fuel filter should last the life of the vehicle under normal driving conditions. If the filter does need to be replaced, proceed as follows:
CAUTIONIf the fuel filter is being serviced with the rear of the vehicle higher than the front, or if the tank is pressurized, fuel leakage or siphoning from the tank fuel lines could occur. to prevent this condition, maintain the vehicle front end at or above the level of the rear of vehicle. also, relieve tank pressure by loosening the fuel fill cap. cap should be tightened after pressure is relieved.
  1. Shut the engine off. Depressurize the fuel system.
  2. Raise and support the vehicle safely.
  3. Detach the fuel lines from both ends of the fuel filter by disengaging both push connect fittings. Install new retainer clips in each push connect fitting.
  4. Note which way the flow direction arrow points on the old filter.
  5. Remove the filter from the bracket by loosening the filter retaining clamp enough to allow the filter to pass through.
The flow direction arrow should be positioned as installed in the bracket to ensure proper flow of fuel through the replacement filter.
  1. Install the filter in the bracket, ensuring proper direction of flow as noted by arrow. Tighten clamp to 15-25 inch lbs.
  2. Install the push connect fittings at both ends of the filter.
  3. Lower the vehicle.
  4. Start the engine and check for leaks.
  1. Before servicing the vehicle, refer to the Precautions section.
  2. Properly relieve the fuel system pressure.
  3. Remove or disconnect the following:
    • Negative battery cable
    • Push connect and R-clip fittings from the fuel filter
    • Fuel filter 0900c15280192eee.jpgFuel filter location and connections–2002–2006
To install:
  1. Install or connect the following:
    • Fuel filter. Torque the nut to 17 ft. lbs. (23 Nm).
    • R-clip and push connect fittings
    • Negative battery cable
  2. Start the vehicle, check for leaks and repair if necessary.

Oct 17, 2008 | 2002 Mazda B-Series

Not finding what you are looking for?
2010 Volvo V50 1.6D Logo

Related Topics:

21 people viewed this question

Ask a Question

Usually answered in minutes!

Top Volvo Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Volvo Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...