Question about Cars & Trucks

1 Answer

How to remove the rear bumper on a 2010 vaukhall insignia

How to remove the rear bumper on a 2010 vauxhall insignia to fit parking sensors (Thanks for any help)

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Cars & Trucks Master
  • 3,103 Answers

If its under warranty have them install these..

Posted on Dec 28, 2013

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 12 Answers

SOURCE: How to Remove the Rear Bumper - BA Fairmont/Falcon

Firstly, you need to remove the rear splash shields from within the rear wheel arches and also the tail lights. Then remove the scrivets from the lover edge of the bar. Next remove the scuff plate at the boot opening and fold the carpet back. There are four nuts which hold the bar on, undo these and then lift the sides of the bar up and pull out. The bar has large clips on the side which hold it in place.

Posted on Aug 22, 2009

  • 2 Answers

SOURCE: removal of front bumper

The bumper is secured using four 13mm nuts.

a) Open the bonnet and look for one 13mm nut on the lower inside of each headlight.
b) Remove the towing eye covers on the lower section of the bumper and you will find one 13mm nut in each.

Hope this helps.
Shane

Posted on Apr 09, 2010

  • 1 Answer

SOURCE: 2005 Audi A4 factory fitted rear parking sensors

Factory fitted sensors continous tone

Posted on Nov 22, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do you fit rear mudflaps to vauxhall insignia


if you are using after market flaps then there will be a problem
talk with a service dealer as to how genuine flaps are fitted ,then make the adaptors to suit what you have

Jun 12, 2016 | Vauxhall Cars & Trucks

1 Answer

How do I replace rear parking sensor


You have to take bumper cover off .
Remove rear bumper fascia. Refer to Rear Bumper Fascia Replacement . Disconnect electrical from the rear object sensor. Lift the locking tabs on the housing and remove the rear object sensor.
Preliminary Procedure
  1. Remove the compartment sill plate. Refer to Rear Compartment Sill Trim Plate Replacement .
  2. Remove rear wheel liners. Refer to Rear Wheelhouse Panel Liner Replacement .
1
Rear Fascia Push Pin Retainers (Qty: 2)
2
Rear Fascia Nuts (Qty: 4)
Tighten
10 N?·m (89 lb in)
3
Rear Fascia Bolts (Qty: 2)
4
Rear Fascia Bolts (Qty: 6)
5
Rear Fascia
Tip
?€¢
Energy absorber and fascia are removed together. Cannot be separate on vehicle.


?€¢
Disconnect the electrical connectors.

Dec 22, 2015 | 2006 Cadillac DTS

1 Answer

Reverse parking sensors


You would need to seek service repairs.

Jan 25, 2014 | Cars & Trucks

1 Answer

How to ajust the handbrake on a vauxhall insignia


How do i adjust my hand brake on a vauxhall insignia year 2010?

Dec 01, 2012 | Vauxhall Cars & Trucks

1 Answer

How do I remove the panel that hold the rear parking sensors on a 2001 S550?


There are six bolts from the bumper into the rear cross member to remove, accessible from inside the boot. You'll have to remove the rubber plugs to get to two of them. After that, remove the boot lining (that's the "trunk" lining if you're a Yank) and you'll see four bolts (two on each side) that secure the bumper by screwing downwards through the metal wing into the top sides of the bumper. Now go underneath the car, and there are two bolts accessible at the rear of the bumper, accessible from beneath. Now you need to uncrew a pair of 10mm plastic nuts under the wheel arch lining/mudflap and two which are behine the rear wheels. Fold the wheel arch lining away from the bumper and there's a screw in the very front of the sides of the wing right at the point where it connects to the wheel arch. remove these (one on each side) and the bumper will slide backwards and off the body. Voila. Piece of cake. Remember to disconnect the wiring to the rear sensors and pull the multiplug through out of the hole, carefully removing the grommet.

Re-fitting is a bit trickier, so use a couple of beer crates or boxes to hold the bumper up below the rear as you line up the tabs on the air exits and slide the bumper back.

Dec 23, 2011 | 2001 Mercedes-Benz S-Class

1 Answer

05' Grand Caravan, told that 2 of the rear bumper parking sensors need to be replaced. What is the proper term for these, as I can't find them anywhere, and how invasive to replace?


I wish I had good news but rarly does this sensor go out. unless someone rear ended you. in this case the bumper cover has to be removed.

Dec 20, 2011 | 2005 Dodge Grand Caravan

1 Answer

How to replace a bmw rear parking sensor


put car into reverse with ignition on (not running) and either listen very closely or feel each sensor with your finger tips, you should hear a clicking noise or feel a ticking on the good sensors. once you have determined the faulty one simply release the two plastic retaining clips and push the sensor through the bumper inwards, then remove plug and fit new sensor

Apr 28, 2010 | 2003 BMW 325

1 Answer

Rear bumper replacement


  Remove the tail lamps,remove the plastic retainers from the wheel well area. Remove the retainers below the tailgate opening and below the bumper. Lift up on the sides of the bumper to disengage the sides of the bumper. Pull it back a little and disconnect the connector for the park aid sensors if equipped. Pull back and it is off.

Oct 19, 2008 | 2003 Mercury Mountaineer

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

295 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...