Question about 2006 Tata Indica LSi

Open Question

Rear wheel bearing repair HOW TO - 2006 Tata Indica LSi

Posted by Anonymous on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

How to replace rear wheel bearing


I think you can take it to the near car repair shop.
_______________
car keys replacement

Oct 08, 2012 | Lincoln Town Car Cars & Trucks

1 Answer

How to instal a rear bearing on a saturn veu 2002?auto repair


This would be a bolt on hub and bearing assembly. You will remove the wheel and the brake rotor or drum. Then unplug the abs sensor if equipped. Remove the axle nut if it's an all wheel drive (it is important to tighten the axle nut to the proper spec after replacing the bearing. Failure to properly torques the bearing will result in premature bearing failure). Remove the four bolts that hold the hub to the knuckle. Rmove the hub/bearing assembly.

Sep 03, 2012 | Saturn Cars & Trucks

1 Answer

How do i pull rear wheel bearings


Replacing outer wheel bearings on a solid axle rear end is a moderately involved operation.

The rear axle cover has to come off so that you can remove the C clips to allow the actual axle to come out. Once out, a bearing puller is needed to remove the old bearing, and a bearing installed may be needed to drive in the new one.

If this sounds out of your comfort zone, a shop should charge $200-$300 to make the repair.

Jun 30, 2010 | 1999 Dodge Durango

1 Answer

Rear wheel bearing is out, how easy to repair


not easy,you will probably need a hydraulic press to remove and reset the bearings

Apr 20, 2010 | 2002 GMC Yukon Denali

2 Answers

How to replace rear wheel bearings


don't have topaz. maybe escort will help guide you.

Section 04-02: Suspension and Wheel Hubs, Rear 1996 Escort, Tracer Workshop Manual
REMOVAL AND INSTALLATION Wheel Bearing and Hub Assembly NOTE: Wheel bearings are not serviceable and should therefore be replaced as an assembly with the wheel hub (1104).

Removal
  1. Raise and support the vehicle.
  1. Remove the wheel and tire assembly.
  1. Remove the hub grease cap (1131) from the wheel hub.
  1. If equipped with disc brakes, remove the rear disc brake caliper (2552) and rear disc brake rotor (2C026). Refer to Section 06-04 for the removal procedure.
  1. If equipped with drum brakes, remove the two brake drum screws and the brake drum (1126).
  1. Unstake the rear axle wheel hub retainer (4B477) securing the wheel hub to the rear wheel spindle (4A013). Remove and discard the rear axle wheel hub retainer.
  2. Remove the wheel hub from the rear wheel spindle.

Feb 06, 2010 | 1990 Mercury Topaz

3 Answers

Right rear wheel wobbles as well as there is a


From what you describe it likely is a very bad axle bearing. I would recommend not driving until repaired.

Oct 31, 2009 | 2000 GMC Jimmy

1 Answer

Rear whheel bering repair


need to find rear wheel bearing isuzu bighorn 3.1 (*** import)

Oct 28, 2009 | 1985 Isuzu Trooper

1 Answer

Loose rear wheel, believe it is the bearing. How do I repair it?


drum brakes you remove rear wheel- speed sensor-grease cap-flange nut-outer bearing-brake drum-inner grease seal-inner bearing-drive the bearing races out of the drum hub.to install -install the inner and outer bearing races.apply grease to the bearings and hub cavity.then you install the inner bearing -inner grease seal-brake drum-outer bearing-flange nut torque it to 159 to 192 ft lbs. THE REAR DISC BRAKE WHEEL BEARINGS-you have to remove rear wheel -wheel speed sensor-brake caliper and rotor-rear axle hub bolts-tone the wheel with tool 09445-21000-carrier assembly-nut after unstaking it-press out the rear axle hub-remove the bearing inner race with tool 09445-21000-remove the bushings from the carrier with tools 09453-33000b and 09545-21100.to install -press in the bushings to the carrier with tools 09453-33000b and 09545-21100- press in the bearings to the hub with tool 09221-21000.tighten the flange nut to meet the concave portion of the spindle-press in the tone wheel with tool 09221-21000-torque the nut to 191 ft lbs -install the hub and bearing assembly to the backing plate and torque the bolts to 88 ft lbs-install the brake caliper and rotor.install the wheel speed sensor if equipped.install the rear wheel.TO BUY THE TOOLS TO DO THE JOB.LOOK UP KENT MOORE TOOLS ON INTERNET.

May 30, 2009 | 1999 Hyundai Sonata

Not finding what you are looking for?
2006 Tata Indica LSi Logo

Related Topics:

12 people viewed this question

Ask a Question

Usually answered in minutes!

Top Tata Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Shira

Level 2 Expert

119 Answers

old marine
old marine

Level 3 Expert

1921 Answers

Are you a Tata Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...