Question about 1999 Ford Ranger SuperCab

1 Answer

4x4 transfercase chain slips under load.

I have a ford ranger 4x4 1999 model. the transfercase has been repaired about 18 months ago. i have only done about 8000km since the repair and now it does exactly the same thing when 4wd is engaged. the chain, seals and clutch were replaced. should the guys who repaired it have replaced other important parts such as sprocket or other essencial parts to avoid this happening again?

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 114 Answers

It depends on what the stuff looked like . But yes a ten year old transfer case should have had all the wearing parts replaced. Maybe the whole case should have been replaced. But maybe it is adjusted wrong . Call anoyher garage to see if they can look at it.

Posted on May 18, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

4x4 will shift to 4 high but will not go to 4 low


Ford Ranger Questions - 4 wheel drive relay clicking under ...

www.cargurus.com > Questions > Ford > Ranger
CarGurusJun 5, 2013 - 4 wheel drive relay clicking under dash - i put my truch in 4x4 the other day and ... and watch it move (or not move) while selecting 4x4 high, low and so forth.... MY 1999 Ford Ranger 4x4 will not go in 4 wheel drive 5 answers.

Sep 14, 2015 | 1999 Ford Ranger SuperCab

1 Answer

1999 ford ranger when holding at 1 speed it fills like transmission slips. Any suggestions


Any slipping-- your trans is done

Pull it & rebuild it- AFTER-you diagnose the
electrical part of the system

Sep 19, 2014 | 1999 Ford Ranger SuperCab

1 Answer

Stuck in 4x4 low how do I get it out


On the back of the transfercase there is an electric shift motor. You can remove it and turn the shift shaft with a cresent wrench to move it to 4 high or 2 high. Caution: be sure to block the wheels so the vehicle can not move before you get under it. If you move the shaft to the neutral position, the truck will roll.It in not likely that you will be able to put the shift motor back on unless you can get the slot in the motor drive to line back up with the shift shaft. I hope this helps you.

Mar 04, 2014 | 1999 Ford Ranger SuperCab

1 Answer

2000 ranger 4x4 blinking lights


There is a black box behind the jump seat on the drivers side. You have to remove the panel to get to it. There is a button on the box that resets the shift motor on the transfercase. It this don't fix the problem, then the shift motor is going bad. I hope this helps.

Mar 01, 2014 | 1999 Ford Ranger SuperCab

2 Answers

Is there a tension adjustment for the chain inside the transfercase


no there is no chain adjustment for any transfer case drive chain in ford or mercury vehicles

Dec 29, 2010 | Mercury Mountaineer Cars & Trucks

1 Answer

1999 ford ranger 4x4 where is the electronic control module located


THAT IS THE ECM,IT SHOULD BE UNDERNEATH THE STEERING WHEEL TO YOUR LEFT,YOU SHOULD BE ABLE TO SEE IT FROM OUT SIDE ALSO,SOME MODELS HAVE THEM UNDER THE DASH ON THE PASSENGER SIDE ALSO.










tim..........

Dec 02, 2010 | 1999 Ford Ranger SuperCab

1 Answer

Probleme with the 4x4 on my ranger 1999


have solenoid that engages 4x4 checked

May 13, 2009 | 1999 Ford Ranger SuperCab

1 Answer

4W will not turn on ford ranger 1999 4x4


that clicking sound you no longer hear is a relay switch behind dashboard ....aftermarket one's sold at all chain auto parts stores

Nov 21, 2008 | 1997 Ford F150 Regular Cab

Not finding what you are looking for?
1999 Ford Ranger SuperCab Logo

232 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75077 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5471 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...