Question about Holden Commodore

Open Question

Ve commodore rear wheel bearing replacement Ve model

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 4369 Answers

SOURCE: rear wheel bearing

SECTION 205-02B: Rear Drive Axle/Differential — Ford 8.8-Inch Ring Gear 2003 Mustang Workshop Manual IN-VEHICLE REPAIR Axle Shaft Removal

  1. Raise and support the vehicle. For additional information, refer to Section 100-02 .
  1. Remove the wheel and tire assembly. For additional information, refer to Section 204-04 .
  1. Remove the rear brake disc (2C026). For additional information, refer to Section 206-04 .
  1. Remove the differential housing cover (4033) and drain the lubricant. For additional information, refer to Differential Housing Cover in this section.
  1. Remove the differential pinion shaft (4211).
    1. Remove the differential pinion shaft lock bolt (4241).
    1. Remove the differential pinion shaft.
  1. s3b~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not damage the rubber O-ring in the axle shaft groove.
    Remove the U-washer (4N237).
    1. Push the axle shafts (4234) inboard.
    1. Remove the U-washer.
  1. s3b~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Damage to the rear brake anti-lock sensor (2C190) may occur if it is not removed before the axle shaft.
    Carefully remove the rear brake anti-lock sensor. For additional information, refer to Section 206-09A .
  1. s3b~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not damage the wheel bearing oil seal.
    Remove the axle shaft.
--------------------------------------------------------------------------------------
Rear Wheel Bearing and Axle Shaft Oil Seal Removal
  1. Remove the axle shaft (4234). For additional information, refer to Axle Shaft in this section.
  1. NOTE: If the wheel bearing oil seal is leaking, the axle housing vent may be plugged.
    Using the special tools, remove the rear wheel bearing and wheel bearing oil seal.
Installation
  1. Lubricate the new rear wheel bearing with the specified lubricant.
  1. Using the special tools, install the new rear wheel bearing.
  1. Lubricate the lip of the new wheel bearing oil seal.
    • Use Premium Long-Life Grease XG-1-C or equivalent meeting Ford specification ESA-M1C75-B.
  1. Using the special tools, install the new wheel bearing oil seal.
  1. Install the axle shaft. For additional information, refer to Axle Shaft in this section.

-------------------------------------------------------------------
Installation
  1. Lubricate the lip of the wheel bearing oil seal
    • Use Premium Long-Life Grease XG-1-C or equivalent meeting Ford specification ESA-M1C75-B.
  1. s3b~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not damage the wheel bearing oil seal.
    Install the two axle shafts.
  1. s3b~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not damage the rubber O-ring in the axle shaft groove.
    Install the U-washer.
    1. Position the two U-washers on the button end of the axle shaft.
    1. Pull the axle shaft outward.
  1. NOTE: If a new pinion shaft lock bolt is unavailable, coat the threads with Threadlock and Sealer EOAZ-19554-AA or equivalent meeting Ford specification WSK-M2G351-A5 prior to installation.
    Install the differential pinion shaft.
    1. Align the hole in the differential pinion shaft with the case lock bolt hole.
    1. Install a new differential pinion shaft lock bolt.
  1. Install the differential housing cover and fill the rear axle with the specified lubrication. For additional information, refer to Differential Housing Cover in this section.
  1. Install the rear brake anti-lock sensor. For additional information, refer to Section 206-09A .
  1. Install the rear brakes. For additional information, refer to Section 206-04 .
  1. Install the tire and wheel assembly. For additional information, refer to Section 204-04 .
  1. Lower the vehicle.

Posted on Apr 10, 2009

  • 1 Answer

SOURCE: Rear Wheel Bearing Repair; 2005 pontiac aztek

Remove the brake caliper
Remove the disc, (rotor)
Remove the 34mm nut on the axel shaft
Remove the three (3) bolts from the back side
You will need a wheel puller (three jaw will work well)
Place the puller over the hub and tighten, this will push the shaft out of the hub. Now you have to pull the hub assy. out of the mounting bracket. I found hitting each side,of the hub with a lead hammer to work well. Don't forget to disconnect the ABS senser on the back side of the hub assy.
Do not over tighten the 34mm axel nut when you install the new assy. If you use an impact whrench on it you will damage the bearing.

Posted on May 03, 2009

Mr BrokRench
  • 1623 Answers

SOURCE: I need instructions on how to replace rear wheel bearings on my 1994 Honda Civic

Bearings are pressed into the hubs...much easier, faster and economical (if you don't have a press) to replace the complete bearing/hub assembly, no pressing is needed, since bearings are already pressed into the new hubs. Cost..aprox, 60 buxs each.
Here are the steps for the rear replacement...
Loosen the lug nuts on a rear wheel. 2) Chock the wheels and jack the rear of the car on the side with the lug nuts that you just loosened. 3) Remove the wheel by removing the lug nuts. 4) Pry open the dust cap covering the center of the axle/spindle. A small screwdriver tapped into the space between the hub and dust cap will work well for this. 5) With the dust cap now removed, use a thin center punch to straighten the little dent in the rim of the spindle nut so that you will be able to turn it freely in the next step. 6) Use a 32mm socket and a large breaker-bar to loosen the spindle nut. Unscrew the nut all the way and place it in a clean, safe area. 7) You should now be able to slide the hub/bearing assembly from the shaft. 8) Installation is the reverse of removal. Use plenty of high-temperature wheel bearing grease on all surfaces before you mount the replacement hub assembly.

IMPORTANT: Torque the spindle nut to 134 ft/lbs....(per manual specs)

When reinstalling the dust caps, tap them gently into place to avoid denting them...Install wheels, jack her down and pat yourself on the back...job complete.
Good luck..hope this will fixya up...please take time to leave me a fixya rateing...

Posted on May 23, 2009

  • 119 Answers

SOURCE: Procedure for replacing rear wheel bearings 2000 Forester

i'm assuming you don't have a hubshark,this is a tool that will alllow you to remove the bearing while the knuckle is attached to the car,you may be able to rent this tool at a auto prts store .if not you need to remove the entie knuckle,first remove the trailing arm bolt,then the lateral link bolt{long and stubborn bolt},disassemble the brake shoes and parking brake cable,abs sensor if equipped the knuckle to strut bolt{no marking necessary they are not eccentric} then you need a to use or borrow a press to remove hub and bearings good luck

Posted on Jul 26, 2009

  • 101 Answers

SOURCE: how do i replace the rear wheel bearing on my peugeot 206

wheel off remove the tin cap in the centure of the hub undo the big nut put the wheel back on with just 2 bolts finger tight so you can pull the hub off.once the hub is off take the 2 wheel bolts back out.now look in side the hub were the big nut was and you will see a sir clip take that out.then use a socket and a bench vice to press the old bearing out.use the socket and bench vice to put the new bearing back in.

Posted on Aug 01, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a v6 ve commodore with a HBE engine can I put a HBE engine in it what is the diffrence Ta garry


yes possible
will create electronic miss- matches to be sorted

Holden Commodore VZ VE V6 Alloytec Motor Engine HBE engine code AUD 1 250...

best ve commodore owners forum around
https://forums.justcommodores.com.au/forums/ve-holden-commodore-2006-2013.75
s-l1600-534lvbbiedo0ovj13canlnto-4-0.jpg

Apr 30, 2017 | Cars & Trucks

1 Answer

Rear hub bearing removal ve commodore how to


If it's pressed in, will need special bearing puller to remove. Most auto parts stores will let you borrow this tool with a small deposit.

Nov 16, 2016 | Cars & Trucks

1 Answer

How do i replace the rear wheelstud n a ve gts commodore


you drive out the old one (use a stud remover press) or hammer, then pull the new one in with a wheel nut and spacers (washers work good)

Sep 13, 2014 | Cars & Trucks

1 Answer

How to remove rear diff from ve commodore?


loosen rear wheels, jack up rear so wheels are free, fit safety stands , drain oil, remove wheels, remove 4 bolts holding axle bearings. remove both axles, remove bolts from tail shaft at diff pinion flange , leave tail shaft in transmission housing or oil will leak out, remove bolts from diff housing, the diff center can now be removed.

Aug 28, 2014 | 1998 Holden VT Commodore

1 Answer

How do I dismantle tailshaft support bearing ve commodore


This will be detailed in a repair manual but basically remove the rear section tail shaft if flanged . If not remove the whole shaft from the car and disassemble the shaft joints near the bearing. Remove the nut and pull / press the bearing from the shaft. It should come as a complete item (bearing ,rubber mount and mounting case). Take care to mark where the flange /section comes off the splines as it is critical to position it exactly on reassembly to prevent vibration of the shaft.

May 02, 2014 | 2006 Holden Commodore SS

1 Answer

What would be causing a rattling/clanging noise coming from the left front wheel area when going over rough roads or road imbedded reflector on a ve commodore


broken spring top. damaged damper. steering idler. bearing plate lose. steering link damaged. would need to jack up that side at test every thing in list. could also be something lose in the side part behind the plastic covers. like a droped spaner

Sep 24, 2013 | Cars & Trucks

1 Answer

How to replace rear bearings in ve commodore


Commodore's are not sold here in the USA. So I'll give it my best shot on two different rear axle setups Since he is mechanically inclined, Look at it. That's what I do before any job. If you have CV axles in back, This is to easy, he will figure it out. Remove the axle nut, remove the bolts for the bearing. Most light duty vehicles are set up like this. Next is the straight axle. You have to remove the differential plate, on most. Remove the bolt to release the center pin.( some others, you have to pry out the axles). Remove the tires, push in on the axles and remove the C clip, pull the axles out. Use a bearing puller or chisel out the bearings. There are different set ups for nissan's and honda's and lexus. These you have to remove the brakes to unbolt the axle to get them out.

Jul 12, 2012 | Holden Cars & Trucks

1 Answer

1998 ford escort rear wheel bearing


Your welcome mate, anytime.

Nov 13, 2011 | Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

105 people viewed this question

Ask a Question

Usually answered in minutes!

Top Holden Experts

yadayada
yadayada

Level 3 Expert

74945 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14185 Answers

Are you a Holden Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...