Question about 2009 Dodge Journey

Open Question

Problem with 2009 dodge journey crankshaft position sensor

Need location of sensor

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

emissionwiz
  • 75822 Answers

SOURCE: were is the crankshaft position sensor located on

ANSWER: CRANKSHAFT POSITION SENSOR - 4.7L V-8 ENGINE
REMOVAL
The Crankshaft Position (CKP) sensor is located at the right-rear side of the engine cylinder block CKP Sensor Location/Removal/Installation - 4.7L V - 8 Engine the cranks sensor is positioned and bolted into a machined hole in the engine block

Disconnect CKP electrical connector at sensor.
Remove CKP mounting bolt CKP Sensor Location/Removal/Installation - 4.7L V - 8 Engine
Carefully pry sensor from cylinder block in a rocking action with two small screwdrivers.
Remove sensor from vehicle.
Check condition of sensor o-ring.
INSTALLATION
Clean out machined hole in engine block.
Apply a small amount of engine oil to sensor o-ring.
Install sensor into engine block with a slight rocking action. Do not twist sensor into position as damage to o-ring may result
CAUTION: Before tightening sensor mounting bolt, be sure sensor is completely flush to cylinder block. If sensor is not flush, damage to sensor mounting tang may result.

Install mounting bolt and tighten to 28 N·m (21 ft. lbs.) torque.
Connect electrical connector to sensor.

Posted on Jun 29, 2010

  • 30 Answers

SOURCE: 04 Dodge SRT 4 crankshaft sensor

The Crankshaft Position Sensor is located directly next to the starter.

  1. On 2.4L SRT-4 remove the lower inner cooler hose from the metal tube.
  2. Remove the Structural Collar
  3. Unlock and disconnect the electrical connector to the crankshaft position sensor.
  4. Remove the crankshaft position sensor bolt.
  5. Remove the sensor
Reverse Order to install except note that:

Use a twisting motion when installing the sensor.

Install and tighten the crankshaft position sensor bolt and tighten to 9 N·m (80 ±15 in. lbs.).

Posted on Aug 16, 2008

csmock132
  • 4669 Answers

SOURCE: Where is the crankshaft position

It is stuck in bellhousing of the transmission near the rear head. The new crank sensor will come with a piece of gasket paper on the end of the sensor. Install the sensor all the way in against the pick-up wheel. When you crank the engine the wheel will rip off the paper and the adjustment will be correct.

Posted on Mar 10, 2009

c17hydro
  • 2984 Answers

SOURCE: I HAVE A 2000 DODGE STRATUS 2.5 V6. WHERE IS THE

Cam is on the end of the block, crankshaft sensor is on the bottom of the block. Both are easy to change....are you changing these due to poor performance or no start condition?

Posted on Mar 21, 2009

rvrfsh
  • 3 Answers

SOURCE: location of crankshaft position sensor

I have a 2005 neon and i found mu crank sensor on the radiator side of the block driver side of center directly below the starter. I hope this helps..

Posted on Apr 15, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Speed sensors located on motor


Lorraine, speed sensors are not located on engines. there are transmission speed sensors and wheel speed sensors.
Check the attached links,instruction and guides, Good luck
"I hope this helped you out, if so let me know by pressing the helpful button. Check out some of my other posts if you need more tips and info."
Speed sensors locations Google Search

Vehicle Speed Sensor Location

vehicle speed sensor VSS

wheel speed sensors Google Search

Apr 08, 2016 | Cars & Trucks

1 Answer

Where is the 02 Oxygen Sensor before the cadalic converter on a 2006 Hyundai Santa Fe


Usually these are located on the exhaust manifold or just below the exhaust manifold and you should be able to see it in the engine bay. On V6 engines there will be one sensor on each of the 2 exhaust banks.
You will probably need to remove the engine cover to see the sensors on your exhaust.

If someone told you to replace these because you got a particular fault code I would be wary. A decent scan tool and basic diagnostics can show if the 02 sensor is working or not. Some faults often blamed on an 02 sensor are not due to faulty sensors.

Jan 09, 2016 | 2006 Hyundai Santa Fe

1 Answer

H2o bank 2 sensor 1 location


Bank and sensor location. Bank 1 refers to the back of cylinders that contain cylinder #1. Bank two refers to the other bank of cylinders that do not contain cylinder #1. Sensor 1 refers to the upstream O2 sensor or the O2 sensor before the catalytic convertor. Sensor 2 refers to the downstream O2 sensor or the sensor located after the Catalytic convertor. I hope that helps, let me know if you have any other questions, good luck.

Mar 25, 2014 | 2000 Cadillac DeVille

1 Answer

I need to know how many 02 sensors are on a 1997 dodge intrepid.


  • Up-stream sensor (located before catalytic converter)
  • Left up-stream sensor (located before catalytic converter)
  • Left down-stream sensor (located after catalytic converter)
  • Right up-stream sensor (located before catalytic converter)
  • Right down-stream sensor (located after catalytic converter)
4 sensors total.

Jul 29, 2010 | 1997 Dodge Intrepid

1 Answer

Location of cam sensor 2003 jeep grand cherokee v8


Answer
pic_12.gif
pic
REMOVAL - 4.7L
The Camshaft Position Sensor (CMP) on the 4.7L V–8 engine is bolted to the front/top of the right cylinder head (CMP Location—4.7L Engine).

It is easier to remove/install sensor from under vehicle.

Raise and support vehicle.
Disconnect electrical connector at CMP sensor (CMP Location—4.7L Engine).
Remove sensor mounting bolt (CMP Location—4.7L Engine).
Carefully twist sensor from cylinder head.
Check condition of sensor o-ring.
See picture for sensor location.


9347d80.gif

Jul 21, 2010 | 2003 Jeep Grand Cherokee

1 Answer

I need to replace my CO2 sensor, but I don't know ...


If you are talking about O2 sensor ?? The sensor is locater either in the exhaust manifold or the exhaust pipe. It's not hard to replace in either location. Hope this will help you.

May 20, 2010 | Cars & Trucks

1 Answer

Need to find and replace oxygen sensor for 2003 chevy ventue


Need a 7/8 open end wrench or a o2 sensor socket. Located in exhaust pipe. The one closest to the engine is Bank 1 Sensor 1. The ones located downstream and known as "Sensor 2"

Jan 06, 2010 | 2003 Chevrolet Venture Passanger

4 Answers

Need to locate knock sensor on 1999 camry V6. Where is located.


i have toyota windom 4vz-fe i need locate knock sensor

May 31, 2009 | 1999 Toyota Camry

1 Answer

Location of oxygen sensor


There is only 4 sensors on a 2000 dodge intrepid and the bank 2 sensor 2 is the sensor located on the right (passenger) side and the one located after the catalytic converter (the one close to the firewall).

Apr 08, 2009 | 2000 Dodge Intrepid

1 Answer

Location of speed sensor a for 99 dodge intrepid


The "Vehicle Speed Sensor" signal is generated by the transmisson output speed sensor. That is the one located at the rear of the case. It is externally mounted. That supplies "vehicle speed" info to the other On-Board Computers. The input turbine speed sensor is located just behind the bell housing area of the case. I believe the trans controller is the only module that needs that info. The Crank Position Sensor give engine RPM info and it is located on the bell housing near the engine block. I hope this helps.

Mar 29, 2009 | 1999 Dodge Intrepid

Not finding what you are looking for?
2009 Dodge Journey Logo

Related Topics:

726 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8202 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...