Question about 2007 GMC Yukon Denali

Open Question

I need to replace the power outlet covers in my GMC Yukon

There are two power outlets on the instrument panel in my Yukon. Both covers are broken and need replaced. Can I replace just the covers or do I have to replace the entire power outlets?

Posted by on

Ad

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: location of fuse box/panel for 2004 yukon denali xl

There are 2 fuse panels in the Denali.
One is a panel on the drivers side, its on the dash but facing the door.

The ohter is under the dash and above the pedals, this one is much tougher to access.

Your Owner's Manual should tell you where the fuses are that you need to access.

Posted on Oct 20, 2008

Ad
  • 1 Answer

SOURCE: power outlets dont work

I just purchased a 2002 Envoy and had the same problem. If you raise the drivers's side rear seat, you will see a big black box. Remove this box by pulling the bottom of the box outward and it will come straight up. Next you will see a black cover. This cover has a push tab on each end. Push
the tabs at the same time and lift up on the cover and it can be removed. Inside the cover there is a fuse diagram. The fuse number for my 2002 was #46. This fuse controls the front plugs and #15 controls the back plugs. Locate the the fuse puller on the top left, then count over to spare fuse #3. Between #3 and #4 the fuse is located about 1 1/2 inches below those fuses. You will see a yellow 20 amp pin fuse (BP/ATM-20RP AUTOZONE). remove and check fuse.

Good luck

Rick

Posted on Jan 07, 2009

  • 181 Answers

SOURCE: 2003 GMC Yukon XL All gauges on instrument panel

Sounds as though u have experience the GM usual cluster failure. They go bad more often then probably any other vehicle. Gm has been replacing some under a goodwill warranty for some customers.

Posted on May 19, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

I have a 2008 gmc acacia. The front and mid auxiliary power outlets don't work. The fuse box is on a horrible location. I can't figure out which fuse it is and I don't want to spend hours...


{: ) At the underhood fuseblock, the AUX PWR fuse 20amps is for the Instrument panel and center console outlets, while the RR APO fuse 20amps is for the rear console and rear power outlets.
If your vehicle is equipped with an accessory 110vac, there is this PWR OUTLET fuse 25amps also at the underhood fuseblock. See red arrows on the sample diagram below:


wyet_helps_12.gif Safety reminders: Use only fuses of the same specifications. A higher fuse rating replacement can heat the wirings and could cause fire.

Jul 21, 2011 | 2008 GMC Acadia

2 Answers

How to replace the heater core in a 1998 gmc Yukon.


Heater Core Removal & Installation To Remove:
  1. Disconnect the negative battery cable.
  2. Drain the coolant from the engine.
  3. Recover the refrigerant.
  4. Remove the glove compartment.
  5. Remove the floor air outlet.
  6. If equipped with a diesel engine, remove the powertrain control module.
  7. Remove the kick panel trim.
  8. Remove the blower motor.
  9. Remove the steering column.
  10. Tilt back the instrument panel assembly.
  11. Remove the coolant recovery reservoir from the engine compartment.
  12. Disconnect the heater hoses and the evaporator tube.
  13. Remove the accumulator.
  14. Remove the fasteners and the HVAC module assembly.
  15. Remove the cover plate on the bottom of the HVAC module.
  16. Remove the heater core and seal from the HVAC module.
HVAC module mounting fastener locations gm-10-00-1003.gif

HVAC module components gm-10-00-1004.gif

To Install:
  1. Install the heater core and seal.
  2. Install the cover plate on the bottom of the evaporator case to the HVAC module.
  3. Install the HVAC module in the vehicle.
  4. Install the accumulator.
  5. Connect the evaporator tube and heater hoses.
  6. Install the coolant recovery reservoir.
  7. Install the instrument panel.
  8. Install the steering column.
  9. Install the blower motor and cover.
  10. Install the kick panel trim.
  11. Install the powertrain control module and tray.
  12. Install the floor air outlet.
  13. Add coolant to the cooling system.
  14. Connect the negative battery cable.
  15. Evacuate and charge the A/C system.
  16. Check the system for leaks.
prev.gif next.gif

Nov 06, 2010 | 1998 GMC Yukon

4 Answers

Replace spedometer cable 2003 gmc yukon xl


There is no speedometer cable on the 2003 Yukon, if there is no transmission issues like shifting problem. Your instrument cluster has gone bad, to pinpoint. Your stepper motor to your speedometer gauge has failed and needs to be replaced. You can do a search on Ebay for the stepper motor for around $10.00 which is better then the $400.00 cost of another instrument cluster.
There was a TSB on the replacement of the instrument cluster for your Yukon free of charge. The only cost to you is the labor charge unless your willing to do the job your self. Just go to the Gm Dealer and give them this TSB Number: # 07187C: Special Coverage Adjustment - Instrument Panel Cluster Gauge Needle Function - (Mar 20, 2009)
Subject:
07187C -- SPECIAL COVERAGE ADJUSTMENT - INSTRUMENT PANEL CLUSTER GAUGE NEEDLE FUNCTION

Models:
2003-2004 CADILLAC ESCALADE, ESCALADE ESV, ESCALADE EXT
2005 CADILLAC ESCALADE, ESCALADE ESV, ESCALADE EXT (U.S. ONLY)
2003-2004 CHEVROLET AVALANCHE, SILVERADO, SUBURBAN, TAHOE
2005 CHEVROLET AVALANCHE, SILVERADO, SUBURBAN, TAHOE (U.S.ONLY)
2003-2004 GMC SIERRA, YUKON, YUKON XL
2005 GMC SIERRA, YUKON, YUKON XL (U.S. ONLY)

Some customers of all 2003-2004 model year and certain U.S. 2005 model year Cadillac Escalade, Escalade ESV, and Escalade EXT; Chevrolet Avalanche, Silverado, Suburban, and Tahoe; and GMC Sierra, Yukon, and Yukon XL vehicles have reported that one or more of the instrument panel (IP) cluster gauges stick, flutter, or become inoperative. This may cause inaccurate readings, including the speedometer and fuel gauge. Special Coverage Adjustment This special coverage covers the condition described above for a period of 7 years or 70,000 miles (110,000 km), whichever occurs first, from the date the vehicle was originally placed in service, regardless of ownership.
Dealers are to replace the instrument panel cluster after the condition has been verified. The repairs will be made at no charge to the customer.

For verified failures between 70,001 miles (110,001 km) and 80,000 miles (130,000 km) on U.S. vehicles, dealers are to provide the customer with an instrument panel cluster (IPC) only. Any additional costs, including labor to replace the instrument panel cluster, will be the responsibility of the customer. Dealers are responsible for the return of the customer's IPC back to the Electronic Service Center

Thank you for using fixya and good luck.

Apr 28, 2010 | 2003 GMC Yukon XL

2 Answers

2003 GMC Yukon XL All gauges on instrument panel stopped working. They all stopped at 0, including spedometer, rpms, fuel, oil, etc. The electrical odometer is still working. Is this a fuse problem or does...


If this is an intermittent problem,
remove the IPC 10A fuse in the fuse box under the hood,
not in the fuse panel by the driver side door,
for 5 minutes.
The electronics will reset.

Dec 10, 2009 | 2003 GMC Yukon XL

1 Answer

REPLACING HEATER CORE


HEATER CORE REPLACEMENT REMOVAL PROCEDURE 1. Remove the fuel injector sight shield. 2. Drain the cooling system. Refer to Draining and Filling Cooling System in Cooling System. 3. Use J 38185 in order to position aside the heater hose inlet and outlet clamps at the heater core. 4. Disconnect the inlet and outlet heater hose from the heater core. 5. Remove the RH Instrument Panel Closeout/Insulator panel. 6. Remove the LH Instrument Panel Closeout/Insulator panel 7. Remove the floor carpet. 8. Remove the rear floor air outlet duct from the holes in the floor reinforcement. 9. Disconnect the rear floor air outlet duct from the heater air outlet cover. 10. Remove the rear floor air outlet duct. 11. Remove the heater air outlet cover screws . 12. Remove the heater air outlet cover heat stakes with a small chisel. 13. Remove the heater air outlet cover from the HVAC module assembly. 14. Remove the heater core cover screws . 15. Remove the heater core cover heat stakes with a small chisel. 16. Remove the heater core cover from the HVAC module assembly. 17. Remove the heater core from the HVAC module assembly. 18. Remove the heater core foam seal (1) from the HVAC module assembly.
INSTALLATION PROCEDURE 1. Install a new heater core foam seal to the HVAC module assembly. 2. Install the heater core to the HVAC module assembly. 3. From the inside of the heater core cover, drill the dimples adjacent to the heat stakes using a 5.5 mm (7/32 in) drill bit. 4. Install the heater core cover to the HVAC module assembly. NOTE: Refer to Fastener Notice in Service Precautions. 5. Install the heater core cover screws . Tighten Tighten all screws to 1.5 N.m (13 lb in) . 6. From the inside of the heater air outlet cover, drill the dimples adjacent to the heat stakes using a 5.5 mm (7/32 in) drill bit. 7. Install the heater air outlet cover. 8. Install the heater air outlet cover screws (2). Tighten Tighten the screws to 1.5 N.m (13 lb in) . 9. Connect the rear floor air outlet duct to the heater air outlet cover. 10. Install the rear floor air outlet duct to the holes in the floor reinforcement. 11. Install the floor carpet. 12. Install the RH Instrument Panel Closeout/Insulator panel. 13. Install the LH Instrument Panel Closeout/Insulator panel. 14. Connect the inlet and outlet heater hose to the heater core. 15. Use J 38185 in order to reposition the heater hose inlet and outlet clamps to the heater core. 16. Install the fuel injector sight shield. 17. Fill the cooling system.

Nov 13, 2009 | 2003 Chevrolet Monte Carlo

1 Answer

Replacing heater core on 2004 monte carlo


REMOVAL PROCEDURE 1. Remove the fuel injector sight shield. 2. Drain the cooling system. Refer to Draining and Filling Cooling System in Cooling System. 3. Use J 38185 in order to position aside the heater hose inlet and outlet clamps at the heater core. 4. Disconnect the inlet and outlet heater hose from the heater core. 5. Remove the RH Instrument Panel Closeout/Insulator panel. 6. Remove the LH Instrument Panel Closeout/Insulator panel 7. Remove the floor carpet. 8. Remove the rear floor air outlet duct from the holes in the floor reinforcement. 9. Disconnect the rear floor air outlet duct from the heater air outlet cover. 10. Remove the rear floor air outlet duct. 11. Remove the heater air outlet cover screws (2). 12. Remove the heater air outlet cover heat stakes (1) with a small chisel. 13. Remove the heater air outlet cover from the HVAC module assembly. 14. Remove the heater core cover screws (2). 15. Remove the heater core cover heat stakes (1) with a small chisel. 16. Remove the heater core cover from the HVAC module assembly. 17. Remove the heater core from the HVAC module assembly. 18. Remove the heater core foam seal (1) from the HVAC module assembly

Nov 08, 2009 | 2004 Chevrolet Monte Carlo

1 Answer

How to replace the blower motor fan assembly in a 2000 GMC Yukon XL K1500 4X4


Blower Motor Removal & Installation Delphi
Blower Motor Replacement (Delphi)

1fb4643.gif
To Remove:
  1. Remove the instrument panel sound insulator panel (if equipped).
  2. Disconnect the electrical connector from the blower motor.
  3. Remove the blower motor insulating cover screws.
  4. Remove the blower motor insulating cover.
  5. Pull the retaining tab down and rotate blower motor counterclockwise to remove.
To Install:

  1. Position the blower motor and turn assembly clockwise until tab locks in place.
  2. Install the blower motor insulating cover.
  3. Connect the electrical connector to the blower motor.
  4. Install the instrument panel sound insulator panel (if equipped).

Visteon

Blower Motor Replacement (Visteon)

878e8d8.gif
To Remove:
  1. Remove the instrument panel sound insulator panel (if equipped).
  2. Disconnect the electrical connector from the blower motor.
  3. Remove the blower motor screws.
  4. Remove the blower motor from the HVAC module.
To Install:
  1. Position the blower motor and install mounting screws.
  2. Connect the electrical connector to the blower motor.
  3. Install the instrument panel sound insulator panel (if equipped).

Oct 02, 2009 | 2000 GMC Yukon XL

2 Answers

How to remove heater core from 2000 Pontiac Montana. Antifreeze leaking on floor.


Wow I hope youre mechanicly inclined, big job the entire dash & carrier have to come out 7-15 hr job if you know what you are doing to much to list hear I would check heater hoses at fire wall first make sure they arnt leaking. I wish you well

Aug 31, 2009 | Pontiac Montana Cars & Trucks

1 Answer

How do you replace the power outlet cover on the dash?


One of the outlet covers below the audio system in the dash is broken. I purchased a new one from a dealer for about $5 and it looked like an easy replacement. However, I am unable to remove the old one from the dash. Please advise.

Jan 05, 2009 | 2007 GMC Yukon

4 Answers

Location of fuse box/panel for 2004 yukon denali xl


There are 2 fuse panels in the Denali.
One is a panel on the drivers side, its on the dash but facing the door.

The ohter is under the dash and above the pedals, this one is much tougher to access.

Your Owner's Manual should tell you where the fuses are that you need to access.

Jun 15, 2008 | 2004 GMC Yukon

Not finding what you are looking for?
2007 GMC Yukon Denali Logo

Related Topics:

211 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

76691 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...