Question about 1989 Toyota Pickup SR5

1 Answer

YN-63 STARTER MOTOR

MANUAL FLYWHEEL

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Toyota Master
  • 20,706 Answers

Why not post a full question.
above are all nouns, devoid of even the hint of a question.

Posted on Dec 28, 2013

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1998 jeep grand cherokee starter. Not engaging to flywheel. Works fine when manually jumped from battery.


Sometimes I take the starter motor off the vehicle. Lay it on the ground, hook up jumper cables properly from battery to starter motor, it should do two things, kick out the drive gear and spin. Do you have a flywheel cover that you can remove and watch the starter drive gear engage the flywheel? Also, check the flywheel teeth.

Sep 25, 2017 | Jeep Cars & Trucks

1 Answer

1995 Buick road master I put a flywheel in now it's cutting my started keep putting new starters in is engine my no good


You keep replacing the starter motors?
The starter motor may be fitted incorrectly and isn't meshing with the ring gear properly.

It may be that ring gear - the teeth - on the flywheel are worn/damaged or even the wrong fit for the starter motor.

Another alternative is that the flywheel isn't torqued up correctly and consequently it - and the ring gear teeth - are out of line. However, I would have thought that an out of balance flywheel would also cause vibration problems. Your car runs okay?

Mar 25, 2016 | Buick Cars & Trucks

1 Answer

Starter relay ground


Usually if the starter spins but does not engage the flywheel, the problem is the flywheel or the bendix drive in the starter. The starter gear is supposed to extend to meet the flywheel when the starter spins.

Apr 24, 2013 | Alfa Romeo Cars & Trucks

1 Answer

My Jeep cherokee not starting after removal of flywheel. Is there a specific way to install the flywheel?


The teeth on the flywheel need to be close enough for the starter motor to catch them when it engages. If you removed it and now the starter just free-spins when starting then you may have installed the flywheel backwards and the starter motor cannot reach the teeth on the flywheel. If its making a loud grinding or pinging sound you may need to manually turn the engine a bit to align the flywheel.

Aug 21, 2011 | 1995 Jeep Cherokee

2 Answers

Starter makes a screeching noise sometimes just after the motor starts


Replace the starter before it ruins the flywheel. You have a worn out drive that applies to the flywheel. Flywheels are very very hard to change, in fact you can change 10 or 15 starters in the same time changing one flywheel

Jul 24, 2011 | 1997 Buick Century

2 Answers

My car lost power as i was driving down the highway and won't crank. when i try to crank it, it makes a horrible noise, like it is already crunk. some say it' sthe starter and someone also told me it's the...


hi all front wheel manual gear cars have a flywheel ? ,it does sound like a starter motor fault but that wouldnt make the car cut out while on the highway. the best way to rule both your flywheel and starter motor out is to bump start the car that way if it still dont start then it not any of them. if the car starts them im 99% sure it will be the starter motor.

Sep 02, 2010 | 1998 Ford Escort

1 Answer

I have a 63 C20 that the starter wont turn over the flywheel but its a good starter and the solenoid is new. The starter is meshing with the flywheel


If the gear is meshing ok with the flywheel it should start unless the one way clutch in the starter gear is bad.

Nov 15, 2009 | 1983 Chevrolet K1500

1 Answer

Hello Friend, I have a Dodge Caravan 1997 and in the process of changing out my water pump and timing belt. I am in the stage where I need to open the damper harmonic bolt. Which direction does this bolt...


I have managed to open the harmonic damper bolt. This bolt opens in the counter clockwise rotation. A breaker bar was used with the flywheel locked in place. In order to get to the flywheel, the starter motor was removed to get access. The manual suggest removing the bell housing plate. This takes more effort and one of side engine mount also need removal. I decided to remove the starter motor instead. In order to remove the starter motor, first remove the cables from the starter motor and three mounting bolts. Secure a rod or a screw driver between the flywheel and bell housing through a hole in the flywheel. The size of the size is about 1/2". This hole was visible when the engine is set to TDC (top dead center). There could be more than one hole but I did not try to rotate the engine to find out. Once the rod or the screw driver in place in the flywheel, use the 22mm socket head and breaker bar and undo the harmonic damper bolt counter clockwise (CCW). I believe an impact air gun could do this job as well. The spec on the bolt is 100 ft lbs torque - Hendry

Jan 13, 2009 | 1993 Dodge Caravan

1 Answer

New starter does not work


The spring on the starter motor helix is either stuck or broke, or the starter gear is jammed in the flywheel gear.

Take the cover off the starter motor and you can see the flywheel, starter gear, spring and helix shaft.

If its just stuck, free it up and spray some WD40 in there.

If the gear was jammed into the flywheel teeth then check for damage and wear. They are made from quite a soft metal and burrs can easily be filed and removed.

The "clunk" you are hearing is probably the starter solinoid. If you think its a more mechanical sound than that, it could be the starter taking up slack against a jammed gear.

If the engine runs file on a pull start, its unlikely to be a jammed gear/flywheel and more likely the spring is broke or the gear is stuck at the base of the helix.

If its none of those things and the clunk is the solinoid, then you will have to check to see if 12v is getting to the starter motor. If so, it might actually be the motor.

So, in order of likelyhood/checking:

1) spring stuck or broke
2) Gear jammed on helix
3) solonoid <-> motor electrics
4) gear jammed on flywheel

Its a good idea to keep in working - very sensible.

Jun 13, 2008 | 2000 Chevrolet Silverado 1500

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

29 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8518 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...