Question about 1999 Chevrolet Malibu

1 Answer

To see a diagram of where bolts are on the water pump.

My water pump is leaking nad need to change it but not sure how , can anyone how me a diagram and if not explain it to me?

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 12 Answers

I gave you the replacement procedure just download the link
http://www.freewebs.com/alliedassult/99%20Mlibu%20Water%20pump%20Replacement.rar

Posted on May 18, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Is there a water system diagram available for a honda ballade 150 luxline 1998?


There is definitely no valve there - the only pressure relief valve would be inside the radiator cap. What you see is leakage from a water pump bolt or from the water pump itself. You could try applying a waterproof sealant to that bolt, but it's tricky - allow the engine to cool FULLY, then remove the bolt and hold your finger over the bolthole while a helper applies sealant to the bolt threads. Quickly put the bolt back in the hole so you don't lose very much coolant, tighten the bolt again.

If that doesn't do it, then the leak is really coming from the front seal of the water pump - meaning the water pump needs to be replaced.

Aug 12, 2014 | Cars & Trucks

1 Answer

How do i change a water pump on my 1994 honda civic ex coupe 1.6l engine?


Stop leaks rarely works and are often a waste of money. Before going after the water pump, make sure it is that, that is leaking. Many of the smaller engines have the water pump in line with the timing belt, meaning both will need to be changed.

Dec 08, 2013 | Cars & Trucks

3 Answers

Proper installation procedure for replacing water pump.


Go to autozone web site they have a help on line feature.

Dec 03, 2010 | 1999 Pontiac Montana

1 Answer

WATER PUMP REPLACE DIAGRAM


  1. Step 1 Drain the antifreeze from cooling system. Remove belt from water pump. Examine and see if you have to remove anything else to get out the water pump. If so make a diagram of everything you are removing so you can put it back together.
  2. Step 2 Remove the hoses from the water pump. Find all bolts holding the water pump in . Loosen each one a little bit. After all are lose you can then remove them. Remove water pump. Put new gasket on and install new water pump. Hook up hoses to water pump. Look at your diagram and replace everything you had to remove earlier. Put the belt back on.
  3. Step 3 Shut the drain on system and refill cooling system. Make sure you use the antifreeze that is designed for system. Run engine for a couple of minutes. Check for leaks and check coolant level. Add if necessary. If there is no leaks you are ready to go.

Jun 04, 2010 | 2001 Mazda MPV

1 Answer

Need to replace my water pump do you have a diagram


5.3L Grand Prix Engine
  1. Place a drain pan underneath the radiator. When the engine is cool, drain the cooling system from the radiator into the pan.
  2. Remove the battery from the engine along with its tray.
  3. Take the drive belt out of the engine.
  4. Loosen and remove the three bolts to the water pump and remove the pump, throwing away the gasket.
  5. Clean the gasket mating surfaces and install the new water pump with a new gasket, tightening the bolts to 89 inch pounds (10 Nm).
  6. Reinstall the drive belt and the battery with the battery tray.
  7. Refill the engine's cooling system with coolant. Start the car and check for leaks when the engine reaches normal operating temperature.
3.5L Grand Prix Engine
  1. Partially drain the coolant from the cooling system.
  2. Disconnect the surge tank outlet hose and remove the drive belt.
  3. Remove the idler pulley and the water pump pulley, making sure to note the locations of the bolts as you remove them as they are various lengths.
  4. Loosen and remove the bolts to the water pump, also taking note at their locations, and remove the pump.
  5. Install the new water pump with a new gasket, tightening the bolts to 124 inch pounds (14 Nm).
  6. Reattach the water pump pulley, tightening the bolts to 106 inch pounds (12 Nm).
  7. Reinstall the idler pulley, tightening the bolts to 37 foot pounds (50 Nm) and install the surge tank hose and drive belt.
  8. Refill the engine's cooling system with coolant.
  9. Start the car and check for leaks when the engine reaches normal operating temperature.
3.4L and 3.1L Grand Prix Engines

  1. Place a drain pan underneath the radiator. When the engine is cool, drain the cooling system from the radiator into the pan.
  2. Disconnect the negative battery cable.
  3. Remove the accessory drive belt guard and the accessory drive belt.
  4. Loosen and remove the water pump pulley bolts and remove the water pump pulley.
  5. Remove the water pump bolts and remove the water pump.
  6. Install the new water pump along with a new gasket, tightening the bolts to 89 inch pounds (10 Nm).
  7. Reinstall the water pump pulley and tighten the bolts to 18 foot pounds (25 Nm).
  8. Reattach the accessory drive belt with the drive belt guard.
  9. Refill the engine's cooling system with coolant.
  10. Start the car and check for leaks when the engine reaches normal operating temperature.

Dec 31, 2009 | 1999 Pontiac Grand Prix

1 Answer

Leaking water pump-- with loud grinding niose--how to change pump


change asap thats the pump grinding.locate the pump shouldnt be to hard should have fluid leaking,get new one.will also need more colant.remove the belt.it should have like three bolts on it.remove the old one make sure the mateing surfaces are clean an free of debry.put new one on.replace belt.add coolant check make sure no leaks.let car idle for awhile check agaiin for leaks.if none job well done if u need more help let me know bertman285@hotmail.com

Oct 06, 2009 | 1998 Buick Regal

1 Answer

I have a 1983 ford econoline van. Do you have a diagram of how the water pump is mounted onto the engine


Short of buying a haynes or chilton manual. the basic instructions are, remove anything that is in your way. fan, fan shroud and brackets. Buy the new pump before starting and place it flat on a piece of cardboard. Use a magic marker and trace it's outline and punch holes through all bolt holes. As you remove bolts from pump, put each through it's corresponding hole. Make sure you make note of any spacers and bracket locations. Once the pump is off make sure that you remove every bit of old gasket material before putting pump back on. Generally it's best to use silicone sealer on at least the pump surface and place the gasket on the pump, waiting 'till its nearly dry before installing (keeps it from moving around while you are working) I also put a thin film of silicone on engine side of gasket just before putting it on. When replacing bolts, snug them finger tight only 'till they are all in. any bolts that will be covered by a bracket need to be tightened first before installing bracket. If you took good notes, the job should not be too difficult.
Only change your pump for the right reasons: If the pump is leaking or the shaft bearing is loose and or the bearing is noisy. Changing the pump for any other reason is a waste of time and money.
replacing a pump that is not leaking will not cure an overheat problem.
good luck....any problems, just ask.

Sep 01, 2009 | 1983 Ford Econoline

1 Answer

I need directions to change my water pump


drain engine coolant.relieve belt tension .and remove the drive belt.remove upper fan shroud.remove fan or fan and clutch assembly.remove water pump pulley and coolant hoses from water pump.remove water pump bolts.then remove pump from engine.pay attention to bolts location because they are different lenghts.clean water pump gasket mounting surface dont scratch .or pump gasket wont seal and leak .apply sealant to water pump bolts.install water pump with new gasket.if gasket paper put a sealant on it.torque water pump bolts to 30 ft lbs.if you got a 2.2L engine torque water pump bolts to 18 ft lbs.install coolant hoses on pump .install water pump pulley.install fan and fan clutch assembly.install the drive belt .and the upper fan shroud.fill the radiator with coolant.then run engine to check for leaks.WARNING AS A SAFETY PRECAUTION REMOVE NEGATIVE BATTERY CABLE SO CAR WONT BE CRANK BY ACCIDENT. ALSOOOO DONT FORGET TO TURN OFF RADIO FIRST BEFORE DISCONNECTING BATTERY SO YOU WONT LOSE YOUR RADIO CODE.

Jun 01, 2009 | 1999 GMC Jimmy

2 Answers

Change water pump


If you have any questions feel free to ask. Let me know if you dont get diagrams(happens sometimes)

0900c1528004319d.jpgReverse rotation water pump—2.5L and 4.0L engines
  1. Before servicing the vehicle, refer to the precautions in the beginning of this manual.
  2. Drain the cooling system.
  3. Remove or disconnect the following: NOTESome 4.0L engines are equipped with a fan clutch that threads Directly on to the water pump shaft. This fan clutch is equipped with right-hand threads. NOTEDo not store the fan clutch assembly horizontally, silicone may leak into the bearing grease and cause contamination. NOTEOne of the water pump bolts is longer than the others. Note the location for reassembly.
    • Negative battery cable
    • Electric cooling fan connector
    • Accessory drive belt
    • Engine cooling fan and pulley
    • Water pump pulley
    • Power steering pump
    • Lower radiator hose from the water pump
    • Heater hose
    • Water pump and discard the gasket
To install:
  1. Clean the mating surfaces of all gasket material.
  2. Install or connect the following:
    • Water pump using a new gasket. Torque the bolts to 17 ft. lbs. (23 Nm).
    • Heater hose
    • Lower radiator hose
    • Water pump pulley. Torque the bolts to 20 ft. lbs. (27 Nm).
    • Power steering pump
    • Engine cooling fan and shroud. Torque the bolts to 31 inch lbs. (3 Nm).
    • Accessory drive belt
    • Electric cooling fan connector
    • Negative battery cable
  3. Fill and bleed the cooling system.
  4. Start the engine, check for leaks and repair if necessary.
3.7L Engine
  1. Before servicing the vehicle, refer to the precautions in the beginning of this manual.
  2. Drain the cooling system.
  3. Remove or disconnect the following:
    • Negative battery cable
    • Fan and clutch assembly from the pump
    • Fan shroud and fan assembly. If you’re reusing the fan clutch, keep it upright to avoid silicone fluid loss!
    • Lower hose
    • Water pump (8 bolts)
  4. Installation is the reverse of removal. Tighten the bolts, in sequence, to 40 ft. lbs. (54 Nm). 0900c1528004319e.jpgWater pump tightening sequence—3.7L

Nov 15, 2008 | 2002 Jeep Grand Cherokee

Not finding what you are looking for?
1999 Chevrolet Malibu Logo

176 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...