Question about Cars & Trucks

1 Answer

Ignition cylinder will not turn - Cars & Trucks

Posted by Anonymous on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Cars & Trucks Master
  • 3,961 Answers

If you have tried jiggling the steering wheel at the same time to make sure the ignition lock is not holding on to it, then the key and lock barrel are worn, a common problem. You will need an auto locksmith.

Posted on Dec 27, 2013

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I know if my ignition switch is bad ?


The electrical part or the key lock cylinder part ?
Ignition Key Cannot Be Removed from the Ignition Lock Cylinder
Did you review the Steering Wheel and Column Description and Operation and perform the necessary inspections?
Go to Step 2
Go to Steering Wheel and Column Description and Operation

2

Verify the key cannot be removed from the ignition lock cylinder.
Is the key stuck in the lock cylinder?
Go to Step 3
System OK

3

Is the vehicle equipped with a manual transmission?
Go to Step 6
Go to Step 4

4

Turn the ignition key to the OFF position.
Can the key be turned to the OFF position and be removed?
Go to Step 6
Go to Step 5

5

Verify the adjustment of the automatic transmission cable. Refer to Shift Control Linkage Adjustment in Automatic Transmission - 5L40-E/5L50-E.
System OK
Go to Step 6
Ignition Can/Cannot Be Turned Off with Transmission in Any Gear
Operate the system.
Does the system operate normally?
Go to Testing for Intermittent Conditions and Poor Connections
Go to Step 2

2

  1. Push the ignition lock cylinder control actuator release button which is on the underside of the ignition key cylinder.
  2. Turn the key to the OFF position and remove the key.
Were you able to turn the key to the OFF position and remove the key?
Go to Step 3
Go to Lock System Does Not Lock

3
  1. Turn OFF the ignition.
  2. Disconnect the ignition lock cylinder control actuator.
  3. Turn ON the ignition, with the engine OFF.
  4. Connect a test lamp between the battery positive voltage circuit and the ignition key/shifter interlock switch supply voltage circuit of the ignition lock cylinder control actuator with a test lamp.
Does the test lamp illuminate?
Go to Step 8
Go to Step 4

Aug 20, 2015 | 2006 Cadillac CTS

1 Answer

I have a 98 Chevy Malibu Ls and the ignition won't


Inspect the old ignition cycle which is out.Is there any problem noticed of Ignition cylinder getting worn out.
Because when issue of ignition not turning off,its faulty ignition lock cylinder or faulty ignition switch.I suggest re-inspect the new ignition cylinder.
For more help,click the help link mentioned below:----

Ignition Switch Will Not Turn Off?
http://schematicsdiagram.blogspot.in/2012/04/ignition-switch-will-not-turn-off.html
----------------

1995 Ford Taurus: Ignition switch not turning OFF?

http://repairhelpcenter.blogspot.in/2012/06/1995-ford-taurus-ignition-switch-not.html

-------------

Ignition Problem Troubleshooting

http://whoisbyme.blogspot.in/2012/07/ignition-problem-troubleshooting.html

------------------

These will help.

Thanks.

Feb 04, 2013 | Cars & Trucks

1 Answer

Ignition switch would start but would not lock into position (RUN) and would shut off and then ignition completely locked down and will not move


The ignition key cylinder in a Buick unlocks the ignition and allows the Buick's engine to start. The cylinder contains a switch on the end of it (inside the cylinder) that sends an electric signal to the starter motor. When the ignition key cylinder fails, the Buick won't start. When this happens, you'll need a new ignition cylinder. Purchase replacement cylinders from Buick.
Difficulty: Moderately Easy
Things You'll Need:

  • Ignition key
  • Punch pin
  • Cross-point screwdriver
  1. 1 Remove the screws on the bottom of the steering column on your Buick. These screws hold the steering column cover on. You may need to tilt the steering wheel to its highest position to access these screws.
  2. 2 Turn the ignition key to the "II" position in the ignition cylinder.
  3. 3 Slide the punch pin into the access slot on the bottom of the ignition cylinder.
  4. 4 Push the pin all the way into the access slot while you pull the ignition cylinder out of the steering column.
  5. 5 Insert the new ignition cylinder into the steering column with the key in the "II" position on the cylinder.
  6. 6 Push the cylinder into the column until it "clicks," indicating that it is locked into the column.
  7. 7 Turn the ignition key to the "Off" position.

Dec 15, 2010 | 1995 Buick Riviera

2 Answers

Ignition


the actuator inside the sterring column that the lock cylinder turns is boken, this is a very complex job and is not for the home tech without a factory service manual.

Apr 21, 2010 | 1996 Ford Taurus

1 Answer

How do you program the keyless remote on a 2002 Intrigue?


1. Close the vehicle doors.
2. Turn OFF the ignition.
3. Remove the key from the ignition.
4. Press and hold the driver side door lock switch in the UNLOCK position.
5. Insert the ignition key into the ignition lock cylinder and remove the key. (Do not turn the ignition key in the lock cylinder.)
6. Insert the ignition key into the ignition lock cylinder and remove the key. (Do not turn the ignition key in the lock cylinder.)
7. Insert the ignition key into the ignition lock cylinder. (Do not turn the ignition key in the lock cylinder.) Leave the ignition key in the ignition lock cylinder.
8. Release the door lock switch. The vehicle will sound three beeps in order to verify the Program Mode has been activated.
9. Press the LOCK and UNLOCK buttons together on the keyless entry transmitter and hold until the vehicle beeps twice to verify that the transmitter has been successfully programmed (this take approximately 15 seconds).
10. Perform the previous step to program up to four transmitters (including your old ones).
11. Remove the ignition key in order to exit the Program Mode.


Good luck and thank you for using Fixya

Mar 09, 2010 | 2002 Oldsmobile Intrigue

1 Answer

2000chevy malibu keyless entry problem need help


1. Close the vehicle doors.

2. Turn ignition to the ON position then OFF.

3. Remove key from the ignition.

4. Press and hold the driver side door lock switch in the UNLOCK position
until step 8.

5. Insert the ignition key into the ignition lock cylinder and remove the key.
(Do not turn the ignition key in the lock cylinder)

6. Insert the ignition key into the ignition lock cylinder and remove the key.
(Do not turn the ignition key in the lock cylinder)

7. Insert the ignition key into the ignition lock cylinder.
(Do not turn the ignition key in the lock cylinder)
Leave key in the ignition cylinder.

8. Release the door lock switch. The vehicle will sound three beeps in order
to verify the Program Mode has been activated.

9. Press the LOCK and UNLOCK buttons together on the keyless remote and
hold unitl the vehicle beeps twice to verify that the keyless remote has been
successfully programmed. This may take approximately 15 seconds.

10. Perform the previous step (9) to program up to four keyless remotesm, including
any old ones.

11. Remove the ignition key to exit Program Mode.

Thanks for using Fixya - a 4 THUMBS rating is appreciated for answering your FREE question.

Sep 22, 2009 | 2000 Chevrolet Malibu

1 Answer

Programing remote contr ol


IMPORTANT: Before entering programming mode, have in possession all of the remotes you will be using on the vehicle. Once you program the remotes , all previous codes will be erased from the memory. The other remotes will not be functional until you program the remotes again.
1. Close the vehicle doors.
2. Insert key in ignition and turn to ON (As far as you can without cranking engine)
3. Turn ignition OFF and remove the key from the ignition.
4. Press and hold the driver side door lock switch in the UNLOCK position.
5. Insert the ignition key into the ignition lock cylinder and remove the key.
| (Do not turn the ignition key in the lock cylinder.)


6.
Insert the ignition key into the ignition lock cylinder and remove the key.
(Do not turn the ignition key in the lock cylinder.)


7.
Insert the ignition key into the ignition lock cylinder. (Do not turn the
ignition key in the lock cylinder.) Leave the ignition key in the ignition lock
cylinder.

8. Release the door lock switch. The vehicle will sound three beeps in order to
verify the Program Mode has been activated.

9. Press the LOCK and UNLOCK buttons together on the keyless entry
transmitter and hold until the vehicle beeps twice to verify that the
transmitter has been successfully programmed (this take approximately 15
seconds).

10. Perform the previous step to program up to four transmitters (including your
old ones).

11. Remove the ignition key in order to exit the Program Mode.

Jun 08, 2009 | 1999 Buick Regal

1 Answer

New Ignition Cylinder doesnt click in?


Lock Cylinder Functional
Removal
  1. NOTE: The following procedure applies to vehicles that have functional ignition switch lock cylinders (11582), lock cylinder keys are available for these vehicles or the lock cylinder key numbers are known and the proper key can be made.

    Disconnect battery ground cable (14301). Refer to Section 14-01 .
  1. Turn ignition switch lock cylinder to RUN position.
  1. Place a 3.17 mm (1/8-inch) diameter wire pin or small drift punch in hole in lower steering column shroud (3530) under ignition switch (11572). Press retaining pin while pulling out on ignition switch lock cylinder to remove it from steering column lock cylinder housing (3511).
Installation
  1. Install ignition switch lock cylinder by turning it to RUN position. Insert ignition switch lock cylinder into steering column lock cylinder housing. Make sure ignition switch lock cylinder is fully seated and aligned in interlocking washer before turning ignition switch lock cylinder to OFF position. This will permit cylinder retaining pin to extend into steering column tube flange hole.
  1. Rotate ignition switch lock cylinder, using lock cylinder key, to ensure correct mechanical operation in all positions.
  1. Connect battery ground cable.

Apr 03, 2009 | 1995 Ford Taurus

1 Answer

Ignition key switch


You have to use a pin or paper lip to insert in hole in igmition switch to release the lock cylinder. The key has to be in "on" position I think.

Removal
  1. Disconnect battery ground cable (14301) .
  1. Turn lock cylinder key to RUN position.
  1. Place a 3.17mm (1/8-inch) diameter wire pin or small drift punch in hole in upper steering column shroud (3530) under ignition switch . Press retaining pin while pulling out on ignition switch to remove it from lock cylinder housing (22074) .
Installation
  1. Install ignition switch by turning it to RUN position and pressing retaining pin. Insert ignition switch into lock cylinder housing . Ensure ignition switch is fully seated and aligned in interlocking washer before turning key to OFF position. This will permit cylinder retaining pin to extend into lock cylinder housing hole.
  1. Rotate ignition switch, using lock cylinder key, to ensure correct mechanical operation in all positions.
  1. Connect battery ground cable.
871404a.gif

Jan 13, 2009 | 1986 Ford Mustang

3 Answers

1998 toyota


There is a pin that you have to push in on the bottom of the lock cylinder housing.It is recessed in a hole.You have to turn the key to acc or on to get it to push in.Once you push it in you can pull the key and lock cylinder out.

Dec 01, 2008 | 1998 Toyota Camry

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

12 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...