Question about Ford Cars & Trucks

1 Answer

On my 1998 ford contour every time i put on the brakes car pulls to the right i have changed rotors pads calipers and bled the lines can anyone help me out pleassssse

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 28 Answers

I would start by checking the suspension. There is most likely some play in a control arm bushing, ball joint, or tie rod or something. Worn suspension parts can cause this and they will pull to the side that has a problem, if it pulls right, the bad part will be on the right. My guess is it's a worn control arm bushing.

Posted on Dec 27, 2013

Testimonial: "thank you i will try that and get back to you"

  • dennis adee
    dennis adee Dec 27, 2013

    Check your rear brakes I'll bet you will find the drivers side rear brake needs to be spooned up /tightened so they engage tighter this will help straighten out the pulling affect your experiencing.

×

Ad

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 635 Answers

SOURCE: Spongy brakes

So long as the brake booster is working, test it by turning on the engine, press the brake pedal all the way down, then shut off engine keeping your foot on the brake pedal, if the pedal comes up slightly pushing against your foot then the booster IS working.

Did you BLEED the brakes??????

Posted on Mar 29, 2010

  • 23 Answers

SOURCE: stuck calipers

Brake lines are not releasing fluid back to master cylinder. Open bleeder and see if wheel will turn. If it does replace brake line to caliper

Posted on May 08, 2010

  • 84 Answers

SOURCE: Replaced brake pads on 2001

you need a new master cyclinder..you needed to open the brake line before you forced the caliper back in ,,,otherwise you force the fliud the wrong way though the master cylinder and ruin the internals

Posted on Jan 05, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Overheating brakes


I think the problem is the brake pad or caliper, brake pad are too thick or the caliper are not good casted.
First try to confirm if you get a right brake caliper ,then confirm the brake disc ,brake pad, if they all ok, tear down the bracket of caliper, put into brake pad, then put into brake rotor.
http://www.fiverhope.com/category-4-b0-Brake-caliper.html

Jun 27, 2013 | Cars & Trucks

2 Answers

Install brake pads on the rear of a 2002 Ford Thunderbird


remove wheel
remove pads, they just clips on to the caliper and will pop right off with a screwdriver.
There are 2 different kinds of calipers that ford uses. on oine you will be able to take a c-clamp and force the piston back into the caliper. ON the other type you have to have a $10 tool from oriellys. This tool will hook to the backside of the caliper and turn the piston back in. ONce the piston is backed off, clip on new pads, and slide over rotor. Should be 1 pad on each side of the rotor.

there is no need to bleed the brakes unless you loosen lines which you shouldnt have to do.

Mar 07, 2010 | 2002 Ford Thunderbird

2 Answers

Tools needed to change rotors


You might require Brake caliper along with the basic tools to work on bolts.

Regards,
HP

Aug 28, 2009 | 1998 Ford Explorer

1 Answer

Pistons in both front calipers stay out, both calipers replaced


You may have a leak in the booster or master cylinder. You can put a pressure tester on the system to test for leaks. It does sound like you have an air leak.
You can try to bleed the master cylinder, then slave cylinder, then brake lines.

Aug 24, 2009 | 1993 Oldsmobile Achieva

1 Answer

Changing the rotors out on my 83 4x4 bronco


I would start with the simplest of solutions and try bleeding the breaks and checking the lines for any leaks. Second, if the brakes were properly bled and there is no leak apparent, I would remove the front caliper on the left side, and have a friend pump the brakes, and see if there is pressure on the caliper itself. It is likely that you may have broken or otherwise damaged a brake line, or the caliper simply chose this mos inconvenient of times to die.

Jun 18, 2009 | 1983 Ford Bronco

2 Answers

Changing rotors and breaks


When you replace the pads you have to retract the pistons into the bore. As the pads wear they stay extended from the brake caliper. The new thinkness of the pads will not allow the pads the slip over the rotors until you retract the pistons. Your pistons may be the type that have to be turned back into the bore.Good luck.

Mar 12, 2009 | 1998 Ford Expedition

2 Answers

Front brakes


A Chilton Repair manual would help you. They start around $12.

Feb 01, 2009 | 1998 Ford Explorer

1 Answer

1998 Ford Explorer brake problem


these rotors are known for rusting onto the vehicle. when you removed them you probably had to beat them off with a hammer. if this is the case then you may have a small amount of surface corrosion on the hub. this could cause your rotor to not sit evenly and cause a wobble. recommend removing the new rotor and cleaning the surface of the hub

Nov 29, 2008 | 1998 Ford Explorer

1 Answer

Front brake pads for 1997 ford ecscort encore


The binding of the brakes is causing the pads to overheat, which is causing the smoke. You need pull the wheel and check things out. Your caliper must be bad (not releasing). You need to replace the caliper, brake pads, and have the rotor cut (a full service parts store or shop cuts the rotor perfectly smooth on both sides), or replaced (it may be cheaper to just buy a new rotor). You should also always change the pads (and check everything else) on the opposite side. So, if u do the brakes on the driver side front, always do the front pass. side at the same time, likewise if u do rear brakes.
Whenever you do brakes u should also flush out the brake lines (by bleeding the brakes) until the brake fluid flows absolutely clear. Old brake fluid is the #1 reason for caliper failure. I've seen many times people replace brake components w/out changing the brake fluid, only to have the brakes wear out very quickly, or not function properly. good luck! hope this helps> please rate this!couontrycurt0

Oct 12, 2008 | 1998 Ford Escort

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

71 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76682 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

fordexpert

Level 3 Expert

5537 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...