Question about 1998 Chevrolet S-10 Pickup

Open Question

Replacing 1996 Chevy s10 reverse light switch

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: 1998 Chevy S10 pickup backup lights don't work

Yes it screws in on right side of tramission and you will need a 7/8 inch deep socket to remove it. You may be able to clean the old one once it is removed. There is a little ball thatgets dirty and may you can get by with cleaning it. Good Luck. Ed

Posted on Sep 06, 2008

  • 12 Answers

SOURCE: 1996 Chevy S10 4x4 - Dash lights need replacing

not easy, you have to remove bottom plastic from underneath the dash, there should be two or three you don't have to go to the passenger side, then the front contour snaps off bring your shifter arm al the way down to 1st gear and the steering colomn as well on that plastic contour you have the 4x4 switch to unplug, rear wiper switch, light switch, and rear hatch switch, wiggle the plastic out, now you should see the instrument cluster there should be two to 4 screws holding that in should be 7 mm screws, now careful, if you have the analog cluster you have the speedmeter cable in back to unclip, if digital odometer it's plugged in directly into the dash and there could be an additional plug on top of the cluster, if the cluster came out unclip the backing and you should see the back of the bulbs but careful some are twist off and many others are soudered on that board you aoto parts counter should have these lights in stock no sweat.... good luck

Posted on Dec 17, 2008

  • 1 Answer

SOURCE: switch wont go from cold to hot

It's the little motor that controls the blend door flap in the heater box. The plastic gears inside crack. Remove the glovebox and you will see 2 screws holding the motor on the heater box, they are sorta hard to get off, but a small wrench will do it. The part is like $90 from the dealer.

Posted on Feb 17, 2009

GM Elec
  • 1000 Answers

SOURCE: 1996 chevy s10 headlights will not burn on high or low beam .

I would take a look at your headlight dimmer switch. The dimmer switch works independent of the DRL system.
Below is the wiring diagram for you vehicle.
Good luck and let me know.
Regards,

0900c15280250497.gif
moz-screenshot-5.jpg

moz-screenshot-3.jpgmoz-screenshot-4.jpg

Posted on Apr 06, 2009

  • 111 Answers

SOURCE: Adjusting or replacing brake light switch on 1994

i don't think there is a adjustment on it, but there is a clip on the brake pedal to hold the brake switch on.

Posted on Feb 19, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why don't my 1998 s10 backup lights work when car is in reverse, stop and tail lights work fine all bulbs and fuses seem to be good ?


if the backup bulbs are good then check the neutral switch as this is where the reverse switch is, its part of the neutral switch. it may have stopped working and need replacing. you will be replacing the neutral switch. if you have power out of the switch then check for power and ground at the light socket as there could be a bad wire or connection.

Aug 16, 2014 | Cars & Trucks

1 Answer

1996 chevy s10 v6 4.3l brake light problem


You did all this replacing but didn't check and follow power.Got any money left.lol,get a meter and check power at brake light switch,see if power is going to switch.

Jan 07, 2013 | Cars & Trucks

1 Answer

1996 Chevy S10 ZR2 No brake lights, CHMSL works, new bulbs, new brake light switch, good ground, hazzards work, signals work runners work, any suggestions?


check voltage from brake switch to signal light switch, signal goes from brake pedal to signal switch then to taillights, i suspect the problem is in that area

Oct 22, 2010 | 1997 Chevrolet S-10 Pickup

1 Answer

The reverse ligths on my mom's S-10 pick up won't come on.


I'm guessing you checked the bulbs. test the reverse light switch. Should be found on the drivers side of the transmission. Should have power leaving it when the truck is in reverse.

Mar 21, 2009 | 1997 Chevrolet S-10 Pickup

1 Answer

Chevy 1996 s10 pedal position code?


Another name for it is throttle position sensor. It is usually on the side of the throttle body, usually black in color, has a 2 wire connection, attached with 2 screws. Needs replacing.

Mar 16, 2009 | 1996 Chevrolet S-10 Pickup

1 Answer

Ack up lights dont work when put in reverse


If all fuses are intact and someone did not fiddle with the wiring or plugged out the back up switch, then its most probably the back up switch. Its fitted on the gearbox.

Jan 15, 2009 | 1992 Honda Civic

2 Answers

No tail lights


Try checking the headlight switch it may have broken contacts in it. Easy fix go to a salvage yard find same make and model truck, swap headlight switches.

Dec 27, 2008 | 1997 Chevrolet S-10 Pickup

1 Answer

1996 Chevy S10 4x4 - Dash lights need replacing


not easy, you have to remove bottom plastic from underneath the dash, there should be two or three you don't have to go to the passenger side, then the front contour snaps off bring your shifter arm al the way down to 1st gear and the steering colomn as well on that plastic contour you have the 4x4 switch to unplug, rear wiper switch, light switch, and rear hatch switch, wiggle the plastic out, now you should see the instrument cluster there should be two to 4 screws holding that in should be 7 mm screws, now careful, if you have the analog cluster you have the speedmeter cable in back to unclip, if digital odometer it's plugged in directly into the dash and there could be an additional plug on top of the cluster, if the cluster came out unclip the backing and you should see the back of the bulbs but careful some are twist off and many others are soudered on that board you aoto parts counter should have these lights in stock no sweat.... good luck

Dec 17, 2008 | 1996 Chevrolet S-10 Pickup

4 Answers

1998 Chevy S10 pickup backup lights don't work


Yes it screws in on right side of tramission and you will need a 7/8 inch deep socket to remove it. You may be able to clean the old one once it is removed. There is a little ball thatgets dirty and may you can get by with cleaning it. Good Luck. Ed

Sep 06, 2008 | 1991 Chevrolet S-10 Blazer

Not finding what you are looking for?
1998 Chevrolet S-10 Pickup Logo

Related Topics:

51 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7754 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...