Question about 1992 Ford F150 SuperCab

Open Question

How to bleed the clutch on a 92 ford f150 4.9 liter

Posted by Anonymous on

Ad

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: 1996 Ford Ranger XLT Clutch Bleeding

The problem is up at the Master Cyl............It comes ou of the firewall and points DOWN at about a 45 deg angle.....The reservoir is remote and the hose is set to the lowest point of the cyl...........The tube TO the slave is 180 deg around facing bottom...........
Take the master cly OFF the firewall.......tilt it so that both inlet and outlet are the HIGHEST point of the cyl........Gravity bleed or vacula the slave.........then reinstall the master
I know it sounds like a lot of work but it's the easiest way to clear the air out of Ranger/Explorer hydraulics

Posted on Sep 18, 2008

Ad
co7196
  • 3433 Answers

SOURCE: how to bleed hydraulic clutch on 92 ford ranger

If there is no bleedr, the loosen the lie and get fluid to at lest that point. The bleeder, not having onwe is unlikely, no offemce, just make sure. If the bleeder is anywhere it dhould or would be at a point higher than the line on the slave cylinder down on the bell housing. Open it and let gravity takr over unti the fluid drips steasdy. Slowly depress clutch once to get fluid moving.If long term non usem The cylinders, master and slave, good luck may have leakage needing replacement.l good luc and be careful. be sure brakes are set and vehicle is in neutral when underneath. Engine need not be running.

Posted on May 14, 2009

emissionwiz
  • 77520 Answers

SOURCE: how do i bleed a clutch a on a 92 ford ranger

U will need to buy a Mityvac brand suction bleeding tool to **** the fluid from the master to the bleed port on the slave cylinder at the trans.
this is the only easy way I have found. u can buy this tool at NAPA and Carquest stores

Posted on Jun 25, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Trying to bleed clutch on 92 ford f150. Have done gravity bleed and everything eles. Get relly good peddel until i start truck and then the peddle is gone till i shut truck back off.


bleeding a clutch is a 2 person or pressure bleed job
have a mate pump the clutch pedal the hold it down while you open the bleeder nipple
close the nipple and repeat the pump action
hold down and open the bleed nipple
repeat the operation until you have a solid pedal and no air coming out
keep an eye on the fluid level in the reservoir

Feb 18, 2017 | Ford F-150 Cars & Trucks

1 Answer

92 ford taurus 3.0 liter belt diagram


Here is a link to an image of a 92 Ford Taurus w/ 3.0 L V6:

https://www.bing.com/images/search?q=92+ford+taurus+3.0+liter+belt+diagram&view=detailv2&qpvt=92+ford+taurus+3.0+liter+belt+diagram&id=1506A7C7D19C3D2C363E9CB094A7FE868F24704A&selectedIndex=10&ccid=tXftPJPP&simid=608017299768673961&thid=OIP.Mb577ed3c93cfb5b8471497c5056eeedco0&ajaxhist=0

Aug 07, 2016 | Ford Cars & Trucks

1 Answer

What is the proper procedure for bleeding a hydrolic clutch on a 92 Ford Ranger?


open the bleeder when somebody press the peddle to the floor then close the bleeder then let peddle up repeat till no air comes out it is some times hard to get to start to bleed

Feb 26, 2016 | Ford Cars & Trucks

1 Answer

Bleed hydraulic clutch


If that is the case you must replace the leaking part.

Feb 28, 2014 | Ford F-150 Cars & Trucks

1 Answer

3/4 tonne ford 4x4 93 clutch has no give can't


Had a 92 Ford 3/4 ton 4x4. And the same problem. I changed the clutch master cylinder, slave cylinder (inside of bellhousing), Disc. pressure plate, & throwout bearing. Cost some money but it was worth it. Never had another problem.

Aug 23, 2013 | Cars & Trucks

2 Answers

I have a 92 acura the pedal clutch sticks to floor and have no clutch


Clutch fluid...check the lines for leaks and what not. In my experience, the clutch is blow....prob need new pressure plate!

Sep 16, 2012 | 1992 Acura Integra Hatchback

2 Answers

I Have a 92 ford probe lx 3.0 v-6 5-speed and everytime i press on the clutch the pedal doesnt come back up any ideas why


hi, you may run out of fluid, find the clutch pump container and fill it up with brake fluid, if you see that is getting better then you have to bleede it out, hope it helps.

Dec 21, 2010 | 1992 Ford Probe

1 Answer

How do i bleed a clutch a on a 92 ford ranger


U will need to buy a Mityvac brand suction bleeding tool to **** the fluid from the master to the bleed port on the slave cylinder at the trans.
this is the only easy way I have found. u can buy this tool at NAPA and Carquest stores

Jun 25, 2009 | 1992 Ford Ranger

2 Answers

Changed clutch master cyl. and clutch still goes to floor


try to gravity bleed the system..............leave the master cap off and open the bleeder screw....sometimes this can take a while.epically if you don't bench bleed the new master.(some clutch masters Ive seen (ford especially) take a lot of pumping literally hundreds of pumps)
hope this helps.Good luck!

Dec 21, 2008 | 1992 Ford Escort 4 Door

2 Answers

92 accord clutch bleed


This system has to be pressure bleed.

Dec 11, 2008 | 1994 Acura Integra

Not finding what you are looking for?
1992 Ford F150 SuperCab Logo

Related Topics:

55 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

77514 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

fordexpert

Level 3 Expert

5627 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...