Question about 1989 Ford F 150

1 Answer

89 ford bronco tranny problems

I have 1989 ford bronco.i just put a new clutch,pilot bearing,line into it.Now i was out 4 wheeling with some friends,and it made bang type sound.i lost all gears,the clutch did not seam to be working. i looked under the truck saw that the pilot bearing was still moving when u put the clutch in, but did not have any gear when running.if its off goes into gear. also if the truck is cold and u start it works great till it warms up...

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 532 Answers

When you try to put it in gear engine off,does it roll either way when you push it?it could be a broken chain in the transfer case,or input shaft in the transfer case

Posted on May 20, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

89 bronc 4wd driver side front wheel leaning in more than left, wheel bearing?


could be are totally out of adjustment camber caster . even saw a bent axle once

Feb 15, 2017 | 1989 Ford Bronco

1 Answer

CHANGE FLY WHEEL ON 1987 FORD BRONCO 11


Changing the fly wheel means dropping the trany pulling the clutch. First remove both drive shafts then unhook the clutch line to the slave on the top of the bellhouse this should be a small U shaper pin you have to pull out a piece of wire can be looped through and make it easier to pull it out.

Once that is out of the way take the tanny cross member out and the exhaust Y pipe needs to come out unless you have a body lift and put a jack or something under the transfercase then take out the bottom bell housing bolts and then the top bell housing bolts then you should be able to work the tranny back mind the bolts on the radius arm cross member you may need to back them down sometimes.

Once it is out then you will have 6 of 13mm bolts on the clutch and 6 of 16 or 17mm bolts holding the fly wheel on there should be blue locktight on the flywheel bolts.

Things to note make sure the fly you your putting on has been machined if it is used put a new pilot bearing in the fly your putting on unless it is new put new clutch on or at the very least a new clutch disk trust me it is worth it.

The bolts on the drive shaft can be a pain spray them with WD-40 or equivalent the night before put never sieze on these when you put them back. When your putting the trany back in watch the clutch line it wants to be down there and it is easy to get it caught.

When you take the thin aluminum plate off take care of it with out that plate you can't start your truck right.

Additional details could find in Autozone.com. Hope this helps.

Dec 21, 2010 | 1987 Ford Bronco II

1 Answer

Hello, I have an 89 ford bronco II with a 2.9


Could be that you have one or more brake lines rotting internally and plugging the line. Check for a soft spot in the brake lines.

Jul 04, 2010 | 1989 Ford Ranger

2 Answers

1989 Bronco: 89 ford bronco i put a new starter new battery new...


Check the battery cables for corrosion near the battery terminal end. Sometimes it builds up under the rubber insulation. I would check the ground wire that runs from the battery to the engine block.

May 16, 2010 | 1989 Ford Bronco

1 Answer

Which 5 speed transmissions will work with an 89


all the early rangers up to the genII and maybe even more will work in you bronco....join the ranger station forums for a lot of insight on your bronco...

Mar 01, 2010 | 1989 Ford Bronco II

2 Answers

Clutch has suddenly gone out on our Ford Bronco II. What do we need to do to get this repaired?


remove the tranny driveline , and shift linkage and speed sensor wires and shifter top and clutch line

Jan 14, 2010 | 1989 Ford Bronco II

1 Answer

Need directions to bleed slave cylinder on '89 bronco 2 4x4


brakes or clutch??,if clutch get assistant to work pedal ,pump a few times then hold down ,you push the clutch arm in with a bar and open the bleed nipple at the same time then close the nipple and repeat ,after about 3/4 goes it should have pressure

Dec 22, 2009 | 1989 Ford Bronco II

1 Answer

Bronco fuel pump 89 to 88


i dont think they will. you would be better off finding the right one versus trying to make something work and then you might have even more problems to deal with

Jan 05, 2009 | 1989 Ford Bronco

1 Answer

Tranny clutch problems in Geo Tracker


well i have test.

if you have 1inch free play in pedal it clutch slips ,
clutch is bad , or the 89 93 bell housings are diffr.

was disk put in not backwards?
is it a new clutch.




Nov 19, 2008 | 1992 Geo Tracker

1 Answer

Bronco tranny wont shift out of first


sounds like you burnt it up. how long did u drive it like that?

Nov 04, 2008 | 1989 Ford Bronco

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

158 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5501 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...