Question about 1998 Honda Passport

1 Answer

Bleeding Brakes What is the proper procedure for bleeding the brakes in my 98 honda passport. The order in which to begin, anything special.

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Vice President:

    An expert whose answer gotĀ voted for 100 times.

    Sniper:

    An expert who has posted more than 50 answers, of which 90% or more were rated as helpful.

  • Expert
  • 95 Answers

NOt really start at fron driver with resivoir cap off and have another give 3 slow steady pumps on the brakes you tightening the vavle back up in the middle of the third mover yer way around the car...pump brakes well after you are donw wit hall 4, if you changed all 4

Posted on May 18, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My rear back breaks won't bleed.We have replaced master cylinder,break cylinder,front&back breaks,resivor.We have the front breaks that bleed every time.My pedal goes to the floor.Any ideas?


Jennifer, some brake systems have special procedures to bleed brake systems, some systems have to be plugged into a special scan tool which will cycle different solenoids to allow proper bleeding. You may have to get a good technician with proper equipment to bleed the brakes.

May 07, 2016 | Cars & Trucks

1 Answer

Can you bleed the brakes system from the top of the brake line


Can you bleed the brakes system from the top of the brake line Rick, No! I will post links to proper bleeding procedures, if you can not do it this way, take it in to a qualified shop. Some vehicles need to use a scan tool during the bleeding process to cycle the pump and valves.
"I hope this helped you out, if so let me know by pressing the helpful button. Check out some of my other posts if you need more tips and info."
How To Bleed Your Brakes Feature

Bleeding Brakes

How to do Complete Brake Flush and Bleed

Mar 22, 2016 | Cars & Trucks

1 Answer

ABS light and traction light and no cruise control


how on earth would the blind know what is wrong.?
scan it? yet?
btw, newer cars cut cruise feature for any signs of danger.
new laws...
the traction needs ABS to work ,so forget that and fix ABS.
ABS needs 2 things to work , brakes and ABS.

so if brakes are bad, then ABS will get upset.
after all, if it cant brake right, how can the puter save you?
if brakes are known to be ok (inspections work here)
but in this case it was BREACHED by you, with out reading the book first.
then scan the ABS. (omg? code for dead sensor?) nah, you caused it..
easy

ABS resets every key on. so...
my guess, if ABS was happy before your actions( you never said)
then you got air in to the system. and failed to follow the FSM instructions on bleeding brakes, in ABS car.

front caliper, did you block the hose with cap, so it didn't allow air to the modulator? oops... never just let them drip... or . max pain.
bleed it again, (using any or all 5 ways to do so, bleeding is skill thing) (many modulators can not just be simply bled)

now Ill quote the 2012 fSM for you , under brakes

Data: -----------------------------------------------------------------
ABS Brake Bleeding
STANDARD PROCEDURE - ABS BRAKE BLEEDING

ABS system bleeding requires conventional bleeding methods plus use of a scan tool. The procedure involves performing a base brake bleeding, followed by use of the scan tool to cycle and bleed the HCU pump and solenoids. A second base brake bleeding procedure is then required to remove any air remaining in the system.

Perform base brake bleeding, (Refer to Brakes - Standard Procedure)(Refer To List 1).

Connect scan tool to the Data Link Connector.

Select ANTILOCK BRAKES, followed by MISCELLANEOUS, then ABS BRAKES. Follow the instructions displayed. When scan tool displays TEST COMPLETE, disconnect scan tool and proceed.

Perform base brake bleeding a second time, (Refer to Brakes - Standard Procedure)(Refer To List 1).

Top off master cylinder fluid level and verify proper brake operation before moving vehicle.

Jul 31, 2015 | 2012 Jeep Liberty Sport 4dr SUV 3.7L V6...

2 Answers

How to bleed vaccum booster brakes


Shouldn't be anything different.
Hydro-boost is different as far as the boost part goes.

Dec 08, 2012 | 1992 Ford F150 SuperCab

1 Answer

How do I properly bleed the abs brakes on my honda accord 1998. The bleed nipples are on top of the brake calipers.


Bleeding ABS active brake systems requires a special tool to hold the pressure valves op3en in the ABS hydraulic control module.

Feb 02, 2012 | 1998 Honda Accord

1 Answer

98 corvette what is the proper procedure to bleeding the brakes


  1. Raise the vehicle on a suitable support.
  2. Remove all four tire and wheel assemblies.
  3. Inspect the brake system for leaks and visual damage.
  4. Inspect the battery state of charge.
  5. Install a scan tool.
  6. Turn ON the ignition, with the engine OFF. With the scan tool, establish communications with the electronic brake control module (EBCM). Select Special Functions. Select Automated Bleed from the Special Functions menu.
  7. Bleed the base brake system. Follow the scan tool directions until the desired brake pedal height is achieved.
  8. If the bleed procedure is aborted, a malfunction exists. Perform the following steps before resuming the bleed procedure:
    1. If a DTC is detected, check for the cause and repair as necessary.
    2. If the brake pedal feels spongy, perform the conventional brake bleed procedure again.

  9. When the desired pedal height is achieved, press the brake pedal in order to inspect for firmness. Remove the scan tool.
  10. Install the tire and wheel assemblies. Inspect the brake fluid level.
  11. Road test the vehicle while inspecting that the pedal remains high and firm.

  1. Raise the vehicle on a suitable support.
  2. Remove all four tire and wheel assemblies.
  3. Inspect the brake system for leaks and visual damage.
  4. Inspect the battery state of charge.
  5. Install a scan tool.
  6. Turn ON the ignition, with the engine OFF.
  7. With the scan tool, establish communications with the electronic brake control module (EBCM). Select Special Functions. Select Automated Bleed from the Special Functions menu.
  8. Bleed the base brake system.
  9. Follow the scan tool directions until the desired brake pedal height is achieved.

Jan 03, 2011 | 1998 Chevrolet Corvette

2 Answers

Replaced brake line, rotors and pads bled brakes all around and the brakes when the truck is off work but once i start the truck the brake pedal goes to the floor and have no brakes at...


Bench Bleed the M/C first, then do not let it run dry during system bleeding. Parts stores sell a kit that helps installed m/c bleeding.

Sep 29, 2010 | 2001 GMC Jimmy

1 Answer

Bleeding brakes, The front brakes will not bleed out


In order to bleed the brakes on this car u need a special tool that holds the ABS Hydraulic control units pop-it valves open, without this special tool that plugs into the ABS you can't bleed the air out of the ABS control valve module, u either have to have the dealer do this or someone who has a factory equivalent of the ABS special bleeding tool, Snap-On tools most likely makes these, they are horribly expensive.

Mar 30, 2010 | 1996 Land Rover Discovery

1 Answer

Just changed rear disc pads and one caliper on 2001 Chevy Blazer...now rear brakes are not working at all...fluid is in lines as it comes out when bleeding...help!


the problem here is in order to bleed the brakes properly u need to have a special tool to open up the ABS high pressure pop-it valves, this special tool will be avail at the dealer or in a generic form at any well equiped front end shop, u just can't bleed the brakes without it, I see this same posted problem over and over, this information is correct, u will need a shop to bleed the brakes

Feb 16, 2010 | 2001 Chevrolet Blazer

1 Answer

98 Camry brakes


I would suggest replacing the caliper hoses and following a proper bleeding procedure before replacing the master cylinder

Nov 02, 2008 | 1998 Toyota Camry

Not finding what you are looking for?
1998 Honda Passport Logo

Related Topics:

216 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...