Question about Kia Amanti

1 Answer

Kia Amanti Ignition failure sensor

P0320 (Ignition falure sensor), P2138 (Accelerator Postion Sensor), and P2127 (Throttle/Peddle Position Sensor codes show. Would I (a rookie) be able to replace the Ignition Sensor for starters?? Thank you.

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Kia Master
  • 42,705 Answers

Code p0320 refers to crank shaft position (CKP) sensor/engine speed RPM sensor-circuit malfunction===causes---wiring CKP/RPM sensor ---ECM. Get your hands on an aftermarket workshop manual for the car and you should be able to replace the items

Posted on Dec 27, 2013

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 55 Answers

SOURCE: position sensor replacement

An 02 neon does not have an APP sensor only a TPS at the throttlebody. Sounds like a bogus code to me.

Posted on Oct 18, 2008

  • 840 Answers

SOURCE: how do i replace the throttle position sensor on my '95 K1500?

its just bolts and its next to the air intake/ Please rate my response thank you very much

Posted on Jan 31, 2009

  • 62 Answers

SOURCE: Throttle/Pedal Position Sensor/Switch B Circuit Range Performance

there is no adjustment on these tps's it's a drive by wire system. If you don't know the vehicle, dont post!
there's 2 sensors contained in the pedal sensor, and one on the throttle plate shaft, more often than not, it's the pedal sensor, and if you replaced that, it's the other one or a loose connection. did you reset the computer after replacing the pedal?

Posted on Feb 09, 2010

  • 67 Answers

SOURCE: 2005 Kia Sedona, Trouble Code P0320. Everything I

This is a common problem usually related to the crankshaft position sensor. Before you replace it, disconnect the electrical connector to the CPS sensor and clean it with electrical contact spray and add a dab of dielectrical grease. If the problem continues, replace the CPS sensor. It is easy to replace and is not very expensive. It just bolts to the engine block with one or two bolts. I believe the CPS sensor on the Sedona is behind the timing cover on the front of the engine.

Posted on Feb 12, 2010

wilsodfarm
  • 986 Answers

SOURCE: I have a Nissan Frontier

Throttle/Pedal Position Sensor/Switch "D" Circuit Low
P2122 - APP Sensor 1 Low Input

Probable Causes:
1 - Failed APP Sensor 1
2 - Open or short circuit condition
3 - Poor electrical connection

----------------------------

P2138 - APP Sensor Performance Condition Fault

Probable Causes:
1 - Failed APP Sensor
2 - Open or short circuit condition
3 - Poor electrical connection
I hope this helps you and thank you

Posted on Feb 14, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2006 impala 3.5 LT check engine and service traction control? Code: P2138


DTC P2138: Accelerator Pedal Position (APP) Sensor 1-2 Correlation
Electronic throttle control problem .
The throttle actuator control (TAC) system delivers improved throttle response and greater reliability and eliminates the need for mechanical cable. The TAC system performs the following functions:
• Accelerator pedal position sensing
• Throttle positioning to meet driver and engine demands
• Throttle position sensing
• Internal diagnostics
• Cruise control functions
• Manage TAC electrical power consumption
The TAC system includes the following components:
• The accelerator pedal position (APP) sensors
• The throttle body assembly
• The engine control module (ECM)

Accelerator Pedal Position (APP) Sensor
The accelerator pedal contains 2 individual accelerator pedal position (APP) sensors within the assembly. The APP sensors 1 and 2 are potentiometer type sensors each with 3 circuits:
• A 5-volt reference circuit
• A low reference circuit
• A signal circuit
The APP sensors are used to determine the pedal angle. The engine control module (ECM) provides each APP sensor a 5-volt reference circuit and a low reference circuit. The APP sensors provide the ECM with signal voltage proportional to the pedal movement. The APP sensor 1 signal voltage at rest position is less than 1 volt and increases to more than 4 volts as the pedal is actuated. The APP sensor 2 signal voltage at rest position is less than 0.6 volt and increases to more than 2 volts as the pedal is actuated.
Search P2138 on youtube ,will show diagnostic steps .

Aug 19, 2017 | Cars & Trucks

2 Answers

Car not taking the gas,code p2122 and p2127


check your aps sensor,accelarator position sensor if its bad and make sure all connector and wire from this sensor to ecu is good,.

Mar 09, 2015 | 2004 Kia Amanti

1 Answer

If i switch on ignition tank motor does not runs


Possible causes Faulty Accelerator Pedal Position Sensor
Accelerator Pedal Position Sensor harness is open or shorted
Accelerator Pedal Position Sensor circuit poor electrical connection
Faulty Electric Throttle Control Actuator


Read more: http://engine-codes.com/p2138_chevrolet.html#ixzz3OUJO7vFr

Jan 11, 2015 | Cars & Trucks

1 Answer

2006 chevrolet express 3500 6.6L code p2127 and p2138


Throttle/pedal position sensor recieving/sending out of range , i'd change the tps

Jun 30, 2014 | 2006 Chevrolet Express Cargo

1 Answer

Accelerator pedal sensor


there is no pedal sensor... there is a throttle position sensor located on the throttle body (near the MAF). Replacing it is simple and self explanatory once you locate it.

Feb 07, 2014 | 2004 Kia Amanti

1 Answer

Accelerator pedal position sensor


have the throtthle body cleaned and then decide if you need it replaced may be dirty

Oct 08, 2013 | 2004 Dodge Durango

1 Answer

Check engine light sensor


DTC P2138: Accelerator Pedal Position (APP) Sensor A/B (Throttle Position Sensor D/E) Incorrect Voltage Correlation.

Accelerator pedal position (APP) sensor A and accelerator pedal position (APP) sensor B are potentiometers, and they are installed in the engine compartment.

The APP sensors A and B are operated via the throttle cable to determine the accelerator opening value when the driver presses the accelerator pedal. The accelerator pedal opening value is converted to a signal in APP sensors A and B and transmitted to the engine control module (ECM)/powertrain control module (PCM) to compute the target position. The target position signal is then transmitted to the throttle actuator control module.

APP sensor A is for the primary control, and APP sensor B is a back-up of APP sensor A in case it malfunctions. Both sensors compare their output voltage to each other for malfunction detection.

When the voltage difference of APP sensor B is out of a fixed range for a set period of time, the ECM/PCM detects a malfunction, and a DTC is stored.

Sep 15, 2013 | 2007 Honda Accord Sedan

3 Answers

Error code p2138


Here is the definition. You may need to have someone check the accelerator pedal position sensor and the circuit.

P2138 NISSAN Description The Accelerator Pedal Position (APP) sensor is installed on the upper end of the accelerator pedal assembly. The sensor detects the accelerator position and sends a signal to the Engine Control Module (ECM).
Accelerator pedal position sensor has two sensors. These sensors are a kind of potentiometers which transform the accelerator pedal position into output voltage, and emit the voltage signal to the ECM.
In addition, these sensors detect the opening and closing speed of the accelerator pedal and feed the voltage signals to the ECM. The ECM judges the current opening angle of the accelerator pedal from these signals and controls the throttle control motor based on these signals.
Idle position of the accelerator pedal is determined by the ECM receiving the signal from the accelerator pedal position sensor. The ECM uses this signal for the engine operation
such as fuel cut.
Read more: http://engine-codes.com/p2138_nissan.html#ixzz26J3D2x8s

Sep 12, 2012 | 2010 Nissan Versa 1.8

2 Answers

Code p2138


P2138 is Throttle Pedal Position Sensor/ Switch D / E Voltage Correlation. Replace the Throttle Pedal Position Sensor/Switch.Remember to have the set code Cleared from the cars computer, this will turn off the check engine light and reset it. Good Luck and have a good XMASS.

Dec 17, 2010 | 2006 Nissan Altima

2 Answers

Kia Amanti 2004 trouble Codes


the p2127 code is an Accelerator position sensor (low input) as is the p(2138) could be moisture or debris in harness plugs. Try using dielectric grease.

Jan 23, 2009 | 2004 Kia Amanti

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

432 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kia Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

yadayada
yadayada

Level 3 Expert

76132 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Kia Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...