Question about BMW X5 Series

Open Question

Reset after battery replacement - X5 Series BMW Cars & Trucks

Posted by on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Reset after battery replacement


What battery and what are you reseting?? if you changed the actual battery that cranks the car and now the VDC light is on, you will have to go to NISSAN dealer and have the "steering angle sensor" re-calibrated. If you changed your battery in the remote, then there is no reset. it should work just fine after the battery is replaced, unless the remote is NG.

Jul 04, 2013 | Nissan Frontier Cars & Trucks

1 Answer

My keyless entry system does not work. I replaced the battery,but it did'nt help. flbob72@aol.com


It may not be the battery, however, if the battery went bad, you must reset the system after replacing battery. Read the owner's manual for instructions on resetting or go to your local GM dealer.

Feb 15, 2010 | 1995 Cadillac Eldorado

2 Answers

2004 bmw 545i dead battery had dealer install new battery now i have 2nd gear jerking with my autotransmission


LMAO take it back to the dealer and tell him to reset the ECM since he was stupid enough to onhook the battery and not reset it!

Jan 13, 2010 | 2004 BMW 5 Series

1 Answer

My 05 tiburon battery was dying so i replaced it then my stereo stopped working its not the fuse is there a reset


Radio 'resets' automatically when power is removed -- so, since you replaced the battery, the time lapse between removal of the old battery and installation of the new battery automatically did it.

Oct 30, 2009 | 2005 Hyundai Tiburon

2 Answers

How do you reset ABS light\system after replacing


take the positive cable off the battery for 10 minutes. then replace it to reset it. if this does not work then take it to ford they have a reset machine.

Jul 27, 2009 | 2000 Ford Focus

2 Answers

Lambda Sond light is on. I can replace the O2 sensor, don't know how to reset the light.


First disconnect the battery and the reset switch is located just beneath the dashboard just above the throttle pedal. un-clip the casing via screws and open it and press the switch. Re fasten case and replace back into position. Reconnect the battery and you're set

May 10, 2009 | 1984 Volvo 240 Series

2 Answers

Replacing sending unit in float tank of 2003 Pontiac Sunfire


HI. please remove the negative battery post before you being this repair. Make sure you have depressurized the tank as well.

Replace the negative battery post after you have finished the sending unit repair.

The cpu will automatically reset once the negative battery post is reattached and the engine fuel pressure builds back up to its normal pressure.

Please rate and have a great day:)

Apr 25, 2009 | 2003 Pontiac Sunfire

1 Answer

Battery Change


Try disconnecting and connecting back battery, it reset the ECU, it can be a problem with the computer, but also a sensor that had gone faulty when replacing battery.
It can also be a short or some open contact caused by moving some wire or connector when the battery has been replaced.
If you cannot reset the ECU by disconnecting battery for a while go to a garage to check what the fault is.


Jul 14, 2008 | 2002 Jaguar X-Type

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

15 people viewed this question

Ask a Question

Usually answered in minutes!

Top BMW Experts

Frankie B

Level 2 Expert

65 Answers

Fred Sops

Level 2 Expert

272 Answers

Doberman

Level 2 Expert

254 Answers

Are you a BMW Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...