Question about 2009 Chevrolet Impala LT

Open Question

Dtc p2127 - 2009 Chevrolet Impala LT

Posted by Anonymous on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Have a 2010 Chevy impala. Reduced engine power. Service traction control and stability track. and check engine light. Codes are P2138 P2122 P0455


Electronic throttle control !
DTC P2120: Accelerator Pedal Position (APP) Sensor 1 Circuit
DTC P2122: Accelerator Pedal Position (APP) Sensor 1 Circuit Low Voltage
DTC P2123: Accelerator Pedal Position (APP) Sensor 1 Circuit High Voltage
DTC P2125: Accelerator Pedal Position (APP) Sensor 2 Circuit
DTC P2127: Accelerator Pedal Position (APP) Sensor 2 Circuit Low Voltage
DTC P2128: Accelerator Pedal Position (APP) Sensor 2 Circuit High Voltage
DTC P2138: Accelerator Pedal Position (APP) Sensor 1-2 Correlation

2009 Chevy Silverado P2138 Accelerator Pedal Position


Circuit/System Description
The throttle actuator control (TAC) system uses two accelerator pedal position (APP) sensors to monitor the accelerator pedal position. The APP sensors 1 and 2 are located within the pedal assembly. Each sensor has a 5-volt reference circuit, a low reference circuit, and a signal circuit.
Two processors are also used to monitor the TAC system data. Both processors are located within the engine control module (ECM). Each signal circuit provides both processors with a signal voltage proportional to pedal movement. The processors share and monitor data to verify that the indicated APP calculation is correct.

DTC P0455: Evaporative Emission (EVAP) System Large Leak

The control module tests the evaporative emission (EVAP) system for a large leak. The control module monitors the fuel tank pressure (FTP) sensor signal to determine the EVAP system vacuum level. When the conditions for running are met, the control module commands the EVAP canister purge solenoid valve OPEN and the EVAP vent solenoid valve CLOSED. This allows engine vacuum to enter the EVAP system. At a calibrated time, or vacuum level, the control module commands the EVAP canister purge solenoid valve closed, sealing the system, and monitors the FTP sensor input in order to determine the EVAP system vacuum level. The following table illustrates the relationship between the ON and OFF states, and the OPEN or CLOSED states of the EVAP canister purge and vent solenoid valves.

Nov 03, 2017 | Cars & Trucks

2 Answers

My check engine light keeps coming on with the slippery road light...diagnostic test with code P2127...what does this mean???


code p2127 refers to accelerator pedal position sensor/switch E --low input==causes wiring short to ground-- APP sensor/switch--TP switch short to ground--TP sensor/ switch
the engine light may be from a traction control problem because of the road conditions

Mar 13, 2015 | 2012 Mazda MAZDA5

2 Answers

Car not taking the gas,code p2122 and p2127


check your aps sensor,accelarator position sensor if its bad and make sure all connector and wire from this sensor to ecu is good,.

Mar 09, 2015 | 2004 Kia Amanti

1 Answer

Hyundai trouble codes p2127


my book shows p2127 code as accelerator pedal position (APP) sensor/switch E-- low input === causes wiring short to ground--APP sensor / switch. IT depends on the manufacturer as to the definition as the TPS can be on the air inlet before the manifold and on others it is at the base of the pedal. Because of the cost I suggest speaking with a dealer service centre to find out where it is and if you can save money by getting a unit from a wrecker that handles you make of vehicle then that is the way to go. Low mileage wrecks will have good units .

Jul 24, 2014 | 2003 Hyundai Santa Fe

1 Answer

2006 chevrolet express 3500 6.6L code p2127 and p2138


Throttle/pedal position sensor recieving/sending out of range , i'd change the tps

Jun 30, 2014 | 2006 Chevrolet Express Cargo

1 Answer

Code p2122 & p2127 any solution?


The pedal position sensor is throwing a code. could be ECM may need to updated

Mar 18, 2014 | Honda Odyssey Cars & Trucks

2 Answers

Reduced engine power, service traction control, service stabilitrak


First of all a scan tool is need for this not a code reader, you need to view scan data after you find what code is stored in the PCM. It could have a problem with the powertrain control module, wiring, or the Accelerator Pedal Position (APP) Sensors. Here are a few codes that could set .
DTC P2120: Accelerator Pedal Position (APP) Sensor 1 Circuit

DTC P2122: Accelerator Pedal Position (APP) Sensor 1 Circuit Low Voltage

DTC P2123: Accelerator Pedal Position (APP) Sensor 1 Circuit High Voltage

DTC P2125: Accelerator Pedal Position (APP) Sensor 2 Circuit

DTC P2127: Accelerator Pedal Position (APP) Sensor 2 Circuit Low Voltage

DTC P2128: Accelerator Pedal Position (APP) Sensor 2 Circuit High Voltage

DTC P2138: Accelerator Pedal Position (APP) Sensor 1-2 Correlation

Oct 02, 2012 | 2008 Chevrolet Tahoe LS

1 Answer

Received code P1400 engine light on what would cause this code?


GMC Truck Envoy - 2WD ' Envoy, Rainier, TrailBlazer, Ascender (VIN S/T) Service Manual ' Document ID: 1655997

DTC P1400
Diagnostic Instructions
• Perform the Diagnostic System Check - Vehicle prior to using this diagnostic procedure.
• Review Strategy Based Diagnosis for an overview of the diagnostic approach.
• Diagnostic Procedure Instructions provides an overview of each diagnostic category.

DTC Descriptor:
DTC P1400: Cold Start Emission Reduction Control System

Circuit/System Description
The catalytic converter must be warmed to efficiently reduce the emissions. The cold start strategy is to reduce the amount of time it takes to warm the catalytic converter. During a cold start, the engine idle speed is elevated and spark timing is retarded to allow the catalyst to warm quickly. This diagnostic monitors the following to build an exhaust energy model:

• Engine speed
• Spark advance
• Throttle position
• Engine airflow
• Engine coolant temperature
• Engine runtime
• Park/neutral position
• Vehicle speed

The actual model is then compared to the expected exhaust energy model.

Conditions for Running the DTC
• A cold start has been detected.
• The vehicle speed is less than 2 km/h.
• The engine is at idle with no input from the accelerator pedal.
• The airflow per cylinder is greater than 80 mg/cylinder.
• DTCs P0101, P0102, P0103, P0106, P0107, P0108, P0112, P0113, P0116, P0117, P0118, P0120, P0121, P0122, P0123, P0220, P0222, P0223, P0201, P0202, P0203, P0204, P0205, P0206, P0300, P0335, P0336, P0351, P0352, P0353, P0354, P0355, P0356, P0502, P0506, P0507, P0601, P0602, P0603, P0604, P0606, P0607, P062F, P0641, P0651, P1101, P1516, P1682, P2101, P2119, P2120, P2122, P2123, P2125, P2127, P2128, P2135, P2138, P2176, P2610 are not set.
• This DTC runs for 15 seconds within the first 70 seconds of start up. This diagnostic runs once per trip when a cold start has been determined.

Conditions for Setting the DTC
The actual exhaust energy model does not match the expected exhaust energy model.

Action Taken When the DTC Sets
• The control module illuminates the malfunction indicator lamp (MIL) when the diagnostic runs and fails.
• The control module records the operating conditions at the time the diagnostic fails. The control module stores this information in the Freeze Frame/Failure Records.

Conditions for Clearing the MIL/DTC
• The control module turns OFF the malfunction indicator lamp (MIL) after 3 consecutive ignition cycles that the diagnostic runs and does not fail.
• A current DTC, Last Test Failed, clears when the diagnostic runs and passes.
• A history DTC clears after 40 consecutive warm-up cycles, if no failures are reported by this or any other emission related diagnostic.
• Clear the MIL and the DTC with a scan tool.

Diagnostic Aids
Any loading of the engine that lowers engine RPM, such as with partial application of the clutch, during the first 70 seconds of engine run time may set this DTC.
Circuit/System Verification
Allow the engine to cool. Monitor the Cold Startup parameter. This should indicate Yes. Start and idle the engine for at least 2 minutes. DTC P1400 should run and pass.

Circuit/System Testing
• Inspect the air intake system for the following:
- If any other DTCs are set, diagnose them first. Refer to Diagnostic Trouble Code (DTC) List - Vehicle.
- Modified, damaged, or restricted
- Dirty or deteriorating air filter element
- Crankcase ventilation system for correct operation--Refer to Crankcase Ventilation System Inspection/Description.
- Water intrusion
- Vacuum leak and other un-metered air downstream of the mass air flow (MAF) sensor
- Intake manifold leak

• Inspect the exhaust system for the following:
- Water intrusion
- Exhaust leak
- Damaged, restricted, modified or enhanced exhaust system--Refer to Symptoms - Engine Exhaust .


Hope helps; keep us updated

Jun 30, 2011 | 2006 Chevrolet Trailblazer Ext

1 Answer

Check engine lite is on, power lost lite is on. code p1276comes up. replaced throttle body, but no change. volts at vac fuse 14 both sides. will not accelerate over 1800 rpm's. 2004 trailblazer with 6cyl.


Your CODE P1276 refer to the Acelerator Pedal Position, Sensor 1 Circuit Range Performance.

Probable cause: Wiring, APP or ECM


GM - P1271 Accelerator Pedal Position Sensor 1-2 Correlation

I also found this... though its for Trailblazers... but may give you a clue:
Reduced Engine Power Message and/or Check Engine Light with any Combination of the following DTCs: P0107 P0112 P0122 P0452 P1120 P1220 P1221 P1271 P1275 P1280 P1481 P1515 P1540 P1633 P1635 P1639 P1682 #PIP3192 - (Oct 18, 2004)

Reduced Engine Power Message and/or Check Engine Light with any Combination of the Following DTCs: P0107 P0112 P0122 P0452 P1120 P1220 P1221 P1271 P1275 P1280 P1481 P1515 P1540 P1633 P1635 P1639 P1682 PCM Repeat.

The following diagnosis might be helpful if the vehicle exhibits the symptom described in the PI.

Condition/Concern:
Reduced engine power message and/or check engine light with any combination of the following DTCs: P0107 P0112 P0122 P0452 P1120 P1220 P1221 P1271 P1275 P1280 P1481 P1515 P1540 P1633 P1635 P1639 P1682

Recommendation/Instructions:
If the SI diagnostics did not isolate a concern, the following information may be helpful:
- Inspect the main engine wiring harness between the PCM and the generator assembly for a potential short to ground. There is a metal wiring harness retainer in this area that secures the main engine harness. If the harness conduit is mispositioned, some of the wiring may become exposed and chaff on the harness retainer. This may eventually cause the exposed circuit to short to ground.

- Inspect the 3 harnesses that connect to the PCM for potential shorts to ground on the metal PCM mounting bracket, just below the PCM. There are plastic harness retainers on the PCM bracket that secure the harnesses to the PCM bracket. If the harness conduit is mispositioned, some of the wiring may become exposed and chaff on the PCM bracket. This may eventually cause the exposed circuit to short to ground.

- If a chaffed circuit is found in either of the above locations, repair the circuit using the necessary SI procedures. Once the circuit is repaired, tape the area of the affected area of the harness to prevent the wires from becoming exposed in the future and secure the harness using the original harness retainer.

This applies to 04:
- 4.2L 5.3L LL8 LM4 Engine with DTC - P2120 or P2122 or P2123 or P2125 or P2127 or P2128 - kw low MIL pedal power reduced #PI01746 - (Feb 17, 2004)
- 4.2L 5.3L LL8 LM4 Engine with DTC - P2120 or P2122 or P2123 or P2125 or P2127 or P2128.

When servicing the vehicle with the VIN you entered, the following diagnosis might be helpful if the vehicle exhibits the described symptoms.

Condition/Concern:
MIL light on. Reduced Power message on DIC. Possibles DTCs P2120 and/or P2122, P2123, P2127, and P2128.

Recommendation/Instructions:
The APP harness is clipped to the accelerator pedal bracket. The harness may chaff on the upper portion of the accelerator pedal causing a short to ground. Verify the harness is not chaffing on the accelerator pedal. After repairing the short, reposition the harness to ensure no contact between the harness and the accelerator pedal.

Hope helpes.

Feb 09, 2010 | 2004 Chevrolet TrailBlazer

2 Answers

Kia Amanti 2004 trouble Codes


the p2127 code is an Accelerator position sensor (low input) as is the p(2138) could be moisture or debris in harness plugs. Try using dielectric grease.

Jan 23, 2009 | 2004 Kia Amanti

Not finding what you are looking for?
2009 Chevrolet Impala LT Logo

Related Topics:

21 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8514 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...