Question about Cars & Trucks

Open Question

Front bumper removal peugeot 3008

How do you remove bumper

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1596 Answers

SOURCE: replacing front bumper on 1999 buick regal

7/16th or 10mm Sheetmetal nuts All over Behind the Bumper Thak Bumper off first

Posted on Jan 16, 2009

  • 840 Answers

SOURCE: Trouble removing 1999 Solara Grille

sorry to tell you that but you must take the bumper off and its pretty easy there are retainers up top remove them remove the bottom of the bumper ones and they may have bolts now for the last part its 100 mm at the fender edge and bumper just slide off and then you can take and change the grille

Posted on Jan 27, 2009

nyrtist
  • 5 Answers

SOURCE: I neede to remove the

Here's some instructions for removing bumper and headlights.

E-Class W211 front bumper removal (standard body style).

Tools needed:
- Automotive wheel ramps (Rhino ramps from Autozone).
- 1/4" drive socket set with 8mm and 10mm sockets.
- #20 torx bit.
- Floor jack, optional but useful.
- Flat blade screwdriver.

Instructions for bumper removal:

1) Turn front wheels full right to remove push-pin fastener at lower front corner of left wheel well plastic splash guard. It's difficult to remove this fastener once the car is up on the wheel ramps.

2) Turn front wheels full left to remove push-pin fastener at lower front corner of right wheel well plastic splash guard.

3) Drive car up on wheel ramps. Block rear tires. Open hood.

4) Remove lower mesh plastic grille. There are five attachment points on the top edge of the grille. You can get to three of them with your hand by reaching between the radiator and the back side of the grille. The two outer ones can be released with a screwdriver also reaching in between the grille and radiator. Once the plastic tabs are released, you can remove the grille by pulling it out from the front of the car.

5) Remove the plastic panel located immediately behind the bumper from the bottom of the engine compartment. This panel is held in place with nine sheet metal screws with a 8mm hex head. Five screws are on the bottom of the car and there are two screws in each wheel well at the inner lower edge. After removing all nine screws you can work the panel free.

6) Disconnect the cable from each fog light and remove both fog lights. They are held in place by two sheet metal screws with a #20 torx head.

7) Remove the side marker bulbs. The one on the passenger side turns clockwise to remove and the one on the driver side turns counter-clockwise.

8) Remove the temperature sensor from its socket on the driver side.

9) If you have a floor jack, raise the car at the jack point on the cross member below the engine. You do not want to raise it off the wheel ramps. But it helps to have more clearance above the tires to work in the front wheel wells.

10) Remove three of the plastic nuts holding the forward half of the plastic wheel well liner in place. It's not necessary to remove the plastic liner. You just need to loosen it up so that you can pull it away from the fender to gain access to the screw and bracket securing the bumper to the fender.

11) Pull back the wheel well liner and remove the sheet metal screw from the rear end of the metal bracket . There is only one sheet metal screw (#20 torx head) holding this bracket in place. Don't attempt to remove the bracket yet. I used a #20 torx bit in a 1/4" socket with a 6-inch extension for a 1/4" drive wrench. The head of the screw faces the ground.

12) Remove the 5mm bolts (8mm hex head) holding the bumper to the headlight assembly between the small lens and large lens (both sides).

13) Remove the two 6mm bolts (10mm hex head) on either side of the large grille area opening.

14) Remove the two 6mm bolts (10mm hex head) securing the bumper to the bottom edge of the crashbar. You can access these bolts through the front where you removed the plastic mesh grille.

15) Remove the three 5mm bolts (8mm hex head) holding each headlight assembly in place. Two longer bolts are on top. One at the rear outer corner and one at the front inner corner. The third bolt is accessed from the bottom. It's in the area above the fog lamps. You don't need to disconnect the headlight cables and remove the assembly. But it helps to allow the headlight assembly to "float" freely while you disengage the bumper from the fender.

16) At this point all of the fasteners holding the bumper in place have been removed. The only thing left to do is to remove the two brackets "clamping" the bumper cover to the lower front edge of the front fenders. Before you do this, position some cardboard boxes, bags of packing material, six packs of paper towels, or other suitable items to protect the bumper in case it falls off the car.

17) The bracket holding the bumper cover to the fender has a "pin" that slips into a slot at the front edge of the bumper cover. There is a matching slot near the front edge of the fender. It's not possible to see this pin from the bottom of the car. Use a flat blade screwdriver to pry the bracket away from the bumper/fender and towards the center of the car. The bracket will "hinge" on the pin at the front end of the bracket. After you swing the bracket away from the bumper, you need to slide it forward to remove it from the slot in the bumper cover and fender. You will probably scratch some paint off of this bracket with the screwdriver. I recommend repainting the scratched areas of the bracket before reinstalling it.

18) After removing the bracket from each side of the car you need to deal with the small plastic "hook" holding the bumper cover to the very front tip of the fender. This hook is an integral part of the bumper cover. Disengaging this hook from the fender is probably the most difficult step of removing the bumper. Simultaneously raise the head light assembly slightly, push the leading edge of the fender outward slightly, and push the bumper cover inward toward the headlight assembly. Don't get too aggressive with the fender. It's aluminum and you will make a real mess if you apply too much pressure on the fender. It took me about 20 minutes to free each side from this hook. It should take you less time, since you now know that the hook exists!

19) Gently pull the bumper forward and away from the car. This is one step where a second person would be helpful. But I did manage to do this step alone. There is a "pulley" like attachment point on each side just below the fender/bumper seam.

To re-install the bumper, reverse the order of the steps above. When re-installing the bracket between the bumper cover and fender, I smeared a thin coating of car wash soap on the bracket to facilitate snapping the bracket back into place.




Posted on Oct 09, 2009

  • 83 Answers

SOURCE: front bumper on my 2001 xterra is rusting. I want

Grab a factory service manual it will make it much easier, plus you may need to remove other parts as well. Here is link to a factory service manual for your 2001 Nissan Xterra.

Posted on Oct 10, 2009

Testimonial: "Thanks, will do."

  • 2 Answers

SOURCE: removal of front bumper

The bumper is secured using four 13mm nuts.

a) Open the bonnet and look for one 13mm nut on the lower inside of each headlight.
b) Remove the towing eye covers on the lower section of the bumper and you will find one 13mm nut in each.

Hope this helps.
Shane

Posted on Apr 09, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to remove the front bumper"?"


To remove you will have to use air tools as it cuts the time to minutes instead of hours. Remove front tires and unplug lights in fiberglass bumper. Then remove all the screws and remove fiberglass .bumper. I will supply and DIY email address so you can follow step by step. Subaru wrx sti remove bumper TUTORIAL DIY

May 06, 2014 | 2006 Subaru Legacy

Tip

How to remove a bumper off a ford puma


How to Remove a front bumper off a ford puma

Removal
1. Remove the radiator grille.
2. Remove the left-hand front wheel.
3. Detach the fender splash shield from the bumper cover and fender (both sides).
4. Remove the air cleaner intake pipe retaining clip.
5. Detach the air cleaner intake pipe from the air cleaner housing.

1 Rotate the pipe clockwise.

2 Detach the pipe.
6. Detach the bumper cover from the fender and support bracket (both sides).
7. Remove the left-hand side bumper retaining nut.
8. Remove the right-hand side bumper retaining nut.
9. Remove the bumper.

Installation
1. To install, reverse the removal procedure.

on Jan 31, 2010 | Ford Focus Cars & Trucks

1 Answer

How to remove bumper


1. Remove rear combination light assembly. A. Remove two mounting screws. B. Disconnect electrical connector from rear side of light assembly.

2. Remove bumper assembly. A. Remove four fasteners and four retaining screws from top of bumper assembly. B. Remove mud flap from bumper assembly. C. Remove two screws from bottom of bumper assembly. D. Remove two screws from side of bumper assembly. E. Remove four bumper mounting bolts from under of vehicle.
3. Install rear bumper in reverse order of removal.

Dec 22, 2013 | 2004 Kia Sedona

1 Answer

How you take off the front bumber


have 96, 95 similar

Section 01-19: Bumpers 1996 Villager Workshop Manual
REMOVAL AND INSTALLATION Bumper and Bumper Cover Front
Removal
  1. Raise and support the vehicle.
  1. Remove the RH and LH front wheel (1007).
  1. Remove the RH and LH front fender splash shield screws. Remove the RH and LH front fender splash shields (16102).




  1. Remove the four front fender brace screws.




  1. Remove the two front fender brace nuts.
  1. Remove the two plastic screws.
  1. Remove the seven clip buttons located under the front bumper cover (17D957).




  1. Remove the RH and LH front turn signal lamps (13369). Refer to Section 17-01 for the removal procedure.
  1. Remove the four front bumper cover brace bolts.




  1. Remove the front bumper cover from the vehicle.




  1. Remove the two front turn signal lamp wire harnesses from the front bumper (17757).



  2. Remove the eight front bumper bolts.




  1. Remove the front bumper from the vehicle.

Mar 02, 2010 | 1995 Mercury Villager

1 Answer

How to replace the rear bumper cover on a Chrysler Pacifica


1. Open liftgate. 2. Remove both taillight assemblies by removing 2 hex-head bolts located in the area revealed when the liftgate is opened. 3. Remove 4 plastic retainers on the very bottom of the bumper cover in the rear. 4. Remove 2 phillips head screws in the wheel well rear lip. 5. Remove 4 pop-up plastic retainers in liftgate area. Use two screw drivers to lift the head and then pull the entire retainer out. 6. Remove a hex-head bolt from each side in the area revealed when the taillight assembly was removed. 7. Bend the bumper cover outward on each side to clear the wheel well lip and remove the bumper. Have a blanket or carpet on the ground to protect the bumper. 8. Remove metal clips from tabs that connect the upper bumper cover to the lower bumper cover. 9. Drill out pop-rivets that connect upper bumper cover to lower bumper cover. 10. Push tabs out of slots to separate the upper and lower bumper covers. 11. Release tab locks on chrome trim pieces and remove from upper bumper cover. 12. Reverse this process to replace the bumper cover.

Feb 16, 2010 | 2006 Chrysler Pacifica

1 Answer

How do you take bumper off a ford puma?


Front Bumper (434230)

Removal
1. Remove the radiator grille.
2. Remove the left-hand front wheel.
3. Detach the fender splash shield from the bumper cover and fender (both sides).
4. Remove the air cleaner intake pipe retaining clip.
5. Detach the air cleaner intake pipe from the air cleaner housing.

1 Rotate the pipe clockwise.

2 Detach the pipe.
6. Detach the bumper cover from the fender and support bracket (both sides).
7. Remove the left-hand side bumper retaining nut.
8. Remove the right-hand side bumper retaining nut.
9. Remove the bumper.

Installation
1. To install, reverse the removal procedure.

Jan 01, 2010 | 2007 Ford F

2 Answers

Need step by step instructions on how to remove a rear bumper cover on a 2007 nissan altima


Rear Bumper: Service and Repair
REAR BUMPER
Removal and Installation
REMOVAL
1. Remove the LH and RH rear combination lamps.
2. Remove both the rear wheels and tires.
3. Remove the LH and RH splash shields.
4. Remove the rear bumper fascia clips and screws, then remove the rear bumper fascia.
5. Remove the rear energy absorbing foam.
6. Remove the rear bumper reinforcement.
7. Remove the rear bumper supports.
INSTALLATION
Installation is in the reverse order of removal.

c674cde.jpg

Nov 12, 2009 | 2007 Nissan Altima 3.5 Sedan

1 Answer

How to remove the rear bumper on a 2005 Kia Sedona


1. Remove rear combination light assembly. A. Remove two mounting screws. B. Disconnect electrical connector from rear side of light assembly. bs6d007a.gif 2. Remove bumper assembly. A. Remove four fasteners and four retaining screws from top of bumper assembly. bs6d007d.gif B. Remove mud flap from bumper assembly. C. Remove two screws from bottom of bumper assembly. bs6d007e.gif D. Remove two screws from side of bumper assembly. bs6d007b.gif E. Remove four bumper mounting bolts from under of vehicle. bs6d007c.gif 3. Install rear bumper in reverse order of removal.

Nov 09, 2009 | 2005 Kia Sedona

2 Answers

Saab 93 bumper removal


It depends on what year your car is,

If it's the pre 02 car then inside the boot there are 2 M10 nuts near the tie down eyes, remove these and then pull the bumper tips outwards whilst pulling the bumper rearwards.

If its the post 02 car then remove the torx screws inside the wheelarch 2each side, remove screw from bottom edge of bumper near to wheel arch each side, remove 2 plastic nuts from lower bumper near spare wheel well, remove rear light clusters then remove the screws behind them, unclip ends of bumper from bodywork and pull rearwards.

May 22, 2009 | 2008 Saab 9-3

1 Answer

I need to know how to remove the font bumper on a 1990 honda civic hatchback.


remove screws from ends of bumper x4,
remove bolts from under bumper x2
remove indicaters from bumper x2
remove 10mm head bolts from behind where indicater were x4
lift bumper up and out

May 02, 2009 | 1990 Honda Civic

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

365 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...