Question about Cars & Trucks

Open Question

Vauxhall fault codes

Code 21 vauxhall meriva 1.4 turbo se 2013

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

chiquititas
  • 1010 Answers

SOURCE: saab 93 engine fault codes p1230 and p1260 ?

What? that's crazy! why wont you take advises from several mechanics? this is the best solution.

Posted on Jun 19, 2008

TwinTurboZ
  • 78 Answers

SOURCE: non start,self diagnosis on the control unit code 21 no ign signal

Distributor is at fault

Posted on May 21, 2009

  • 21 Answers

SOURCE: MY VW POLO SHOWS FAULT CODE ; P0106 ABSOLUTE MANIFOLD PRESSURE SE

this a map sensor, probably just need the sensor replaced, it measurese intake vaccum and adjusts air/fuel mixture accordingly

Posted on Oct 07, 2009

Testimonial: "MANY THANKS TO HONDABOY 47. SPOT - ON. PROBLEM SOLVED!"

  • 1 Answer

SOURCE: suzuki grand vitara fault code

I guess you have an HDI engine (possibly RHZ) as this fault is very common on that model. Quite possibly it will just disappear. It is not likely to be the turbo. Swap the electrovalve (pneumatic solenoid) which controls the turbo with one of the others (there are three beside each other on the inside of the wing, and see what happens. If the fault moves elsewhere that confirms electrovalve fault - so replace valve it.
If not check the vacuum hoses and test things such as the EGR for vacuum leaks. Another possibility is a faulty (or even just dirty) MAF. This is very easy to remove- it is on air intake - so remove and clean with wWD40 or similar.

Posted on Oct 27, 2010

emissionwiz
  • 75822 Answers

SOURCE: where is the fuel pump relay on a 2004 vauxhall meriva

It is on the passenger side of the engine compartment under the wiper panel. its deep in because of the body design. you'll see a relay box. It should click on and then quickly off when the key is turned to run without starting the engine

Posted on Sep 13, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a vauxhall meriva 1.7cdti and yester day i lost power and when i try toget up to full power when moving it go no get up and go


the system is probably in limp mode setting
run the fault codes and fix what is found to be faulty
reset the ECM using a scan tool when the fix is completed

Sep 29, 2016 | Vauxhall Cars & Trucks

1 Answer

What are the torque settings and sequence for a Meriva B 1.4 turbo


What components are you trying to fit? My advice would be to buy a good workshop manual and go from there Vauxhall Opel Meriva Petrol Diesel 03 May 10 03 to 10

Jan 15, 2016 | Vauxhall Cars & Trucks

1 Answer

What does code 258 mean on my Vauxhall meriva?


This is not a Fault Code as such, but a Message Code. Message code are listed in the owners Handbook. Message 258 is telling you that the Park Assist Function is OFF. So don't go backing into anything. You will need to turn On the Park Assist to extinguish the message.

Aug 17, 2015 | Vauxhall Cars & Trucks

1 Answer

My vauxhall meriva will not start garage cannot find anything wrong gave it a full service. someone says it could be my key.


If it is indeed the key, you will see the engine management light flashing rapidly as you try to start it. If it aint flashing,,,it aint the key.Could be numerous things...garage need to use computer to find fault codes / check live data...not a complex car.

Feb 20, 2015 | Vauxhall Cars & Trucks

1 Answer

Vauxhall meriva 1.4 se 2011 engine is missing when warm at 30mph and bringing abs warning light up which then stays on and engine warning light flashers a few times and goes off no faults found what t


check your coil pack,remove both the screws ,disconnect the wiring plug and pull the coil pack up, have a look down each plug cap, there will probably be corrosion on the contacts or on the top of the plugs,this doesent always record a DTC

Feb 16, 2015 | Vauxhall Cars & Trucks

1 Answer

Just bought 1.4t 2010 meriva showing code21 any answers


You need a code reader(expensive) or a Vauxhall/Opel specialist unless anybody reading this knows what the code means. Have you tried the owners club forums?

Nov 14, 2014 | 2010 Opel Meriva 1.4

1 Answer

2004 corsa c auto wont start when warm fault codes u2103 u2104 u2105 u2107


i have a meriva and battery light comes on and spedometer drops to zero then flickers i have changed alternator and still same problem sometimes car wont start fault codes are u2105 u2103 b1484 u2104 i have been told i need repair done on ecu

Nov 20, 2013 | Vauxhall Cars & Trucks

1 Answer

I have a warning light on my vauxhall


Emisions related can be a lot of things. It would have logged a fault code to the computer. You need the vehiclescomputer scaned to reveal the fault. Could be lots of things (O2 sensor in the exhaust, airflow sensor, vacume leak, misfire, etc...) the only way to know will be to have the code extracted.

Sep 28, 2012 | Opel Meriva Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

436 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...