Question about 2007 Pontiac Torrent

Open Question

2007 torrent passenger window stuck in down position

What color is the wire that controls the windows

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 7 Answers

SOURCE: Key stuck in ignition of 2007 Pontiac Torrent

well to get the key out all you need to do is takeWD-40 and put the small hose on it as far as you can down the ignition the spay it and wiggle the key UP AN DOWN then take a sewing needle and wiggle it around in the ignition som anything holdin the key in there will come loose. TRUST ME I HAD THE SAME PROBLEM WITH MY 2006 SILVERADO

Posted on Jan 18, 2009

  • 97 Answers

SOURCE: My passenger window is stuck in the down position,

since your other power windows are working and if the other interior accessories are working fine I would suggest having the power window motor actuator checked and replaced if found to be defective.

Posted on Aug 19, 2009

  • 7353 Answers

SOURCE: Passenger window won't go up

At the passenger switch its the Dark Blue and Brown wires.At the Master switch its the Light Blue and Tan wires. But I think your problem is a bad Master Switch

Posted on Sep 01, 2010

airjer995
  • 5332 Answers

SOURCE: Looking for wiring diagram for

You'll need to pull the door panel and check for power and ground at the 2 wire connector located near the window motor (there should be a dark blue wire and a brown wire). With a test light there should be power on one of the two wires at any time. If there is power on both wires with the switch in the up position than the switch is bad. If the only wire powered up in the up position is the dark blue wire than try tapping the motor while holding the switch in the up position. If it starts to work than the motor is bad.

On a side note check for power with all the connectors plugged in. You can also jump the connections at the motor. Supply a ground to the brown wire and supply power to the dark blue wire and the window should go up.

Posted on Sep 24, 2010

dcramer531
  • 1654 Answers

SOURCE: Hello I need help locating the fuse/relay for my

The 2007 Pontiac G6 engine compartment fuse block is located on the driver's side of the engine compartment, near the battery. The wiring circuits in Pontiac G6 are protected from short circuits by a combination of fuses, circuit breakers and fusible links. This greatly reduces the chance of damage caused by electrical problems. Below diagram and table shows 2007 Pontiac G6 Engine Compartment Fuse Panel, Relay and the Circuit Protected.
pontiac-g6-engine-compartment-fuse-panel_thumb.png The fuse is in location 50

Posted on Nov 25, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2003 gmc envoy Windows fuse


Are all windows not working ? Two separate circuit breakers left & right . Both in rear fuse box . Fuse Block - Rear Beneath the left rear seat
Check for broken wires inside the rubber boot from body to doors.
Do you know about electronic control modules ?
The power window system consists of the following components:
?€¢
Driver door module (DDM)


?€¢
Passenger door module (PDM)


?€¢
Body control module (BCM)


?€¢
LR power window switch


?€¢
RR power window switch


?€¢
Window up and window down relays in each of the rear passenger window switches


?€¢
Window lockout switch


?€¢
Reversible power window motors in each of the doors (circuit breaker protected)


?€¢
LT DOOR CB 25A (System power for left rear window)


?€¢
RT DOOR CB 25A (System power for right rear window)


The power window system will operate anytime the retained accessory power (RAP) system is active or when the ignition switch is in the ACCY or ON position.
The DDM contains 4 power window switches which are integral components. Closing any of the normally open, rocker type switches provides the DDM with a request for power window operation. The switches for the 2 front windows have 3 positions Up, Down and Express Down, while the switches for the rear windows have only 2 positions, Up and Down. Each of these switches and their positions is a direct input into the DDM. Upon receiving a request for power window operation, the DDM, transmits a class 2 message indicating the switch and it's changed position.
The PDM contains a single power window switch that is an integral component. Closing of this normally open, rocker switch provides the PDM with a request for the front passenger power window operation. The switch for the front passenger window has 2 positions Up and Down. Each of these switch positions is a direct input to the PDM.
The 2 rear passenger doors have there own switches. Each of the switches contain a power window up and down relay. A switch activation alone can control the up and down functions of the rear windows. However the BCM, upon receiving a class 2 message from the DDM, can control the set of relays which will activate the rear window motors.

Check

Oct 21, 2016 | 2003 GMC Envoy

1 Answer

Right side windows does not work from drivers door or pass.and rear door 2007 Silverado new body


What's with the 1994 C/K 2500 above an 2007 Silverado ? 07 on 94 frame ? New body have all the 07 electronics ?
Power Window System Controls (RPO A31/AN3/DL3)
The power window system will operate anytime the Retained Accessory Power (RAP) system is active or when the ignition switch is in the ACCY or ON position.
The driver master control switches are integrated into the DDS. When a power window switch is activated in the up or down positions the DDS supplies power and ground to the window motor control circuits to drive the window motor in the required direction. Prior to activating a power window motor the DDS will supply the control circuit with a low current bias voltage in order to determine that a short to ground condition does not exist and during window motor operation the DDS continues to monitor the motor current to verify proper window motor operation.
The DDS controls the passenger window through a GMLAN message to the PDS. When a power window switch is activated in the up or down positions the PDS supplies power and ground to the window motor control circuits to drive the window motor in the required direction. Prior to activating a power window motor the PDS will supply the control circuit with a low current bias voltage in order to determine that a short to ground condition does not exist, and during window motor operation the PDS continues to monitor the motor current to verify proper window motor operation. (Scan tool support is available for this system)
Do you know what GMLAN is ? serial data communication network
How to Diagnose Controller Area Network CAN GMLAN is general motors C.A.N
Passenger Power Window Inoperative
  1. Ignition OFF, disconnect the C1 harness connector at the PDS.
  2. Test for less than 1 ohm between the ground circuit terminal 6 and ground.
  3. ?‡'
    If greater than the specified range, test the ground circuit for an open/high resistance.

  4. Ignition ON, verify that a test lamp illuminates between the B+ circuit terminal 2 and ground.
  5. ?‡'
    If the test lamp does not illuminate, test the B+ circuit for a short to ground or an open/high resistance.

  6. Ignition OFF, reconnect the harness connector at the PDS.
  7. Ignition ON, observe the scan tool Passenger Window Switch parameters while using the passenger power window switch. The reading should change between Off/Up/Down/Express Down.
  8. ?‡'
    If the parameter does not change, replace the PDS.

  9. Ignition OFF, disconnect the harness connector at the passenger window motor.
  10. Connect a test lamp between control circuit terminal A and control circuit terminal B.
  11. Ignition ON, command the passenger window UP and DOWN by using the passenger window switch. The test lamp should illuminate when commanding the UP and DOWN states.
  12. ?‡'
    If the test lamp is always OFF during either of the commands, test for a short to ground or open/high resistance on either control circuit. If the circuits test normal, replace the PDS.


    ?‡'
    If the test lamp is always ON, test for a short to voltage on either control circuit. If the circuits test normal, replace the DDS.

  13. If all circuits test normal, test or replace the passenger window motor.

Sep 08, 2016 | 1994 Chevrolet C/K 2500

2 Answers

Driver door will not work lock or windows


They hooked into wiring they shouldn't have >
Power Window System Components
The power window system consists of the following components:
?€¢
Driver door module (DDM)


?€¢
Passenger door module (PDM)


?€¢
Body control module (BCM)


?€¢
LR power window switch


?€¢
RR power window switch


?€¢
Window up and window down relays in each of the rear passenger window switches


?€¢
Window lockout switch


?€¢
Reversible power window motors in each of the doors (circuit breaker protected)


?€¢
LT DOOR CB 25A (System power for left rear window)


?€¢
RT DOOR CB 25A (System power for right rear window)

Power Window System Controls
The power window system will operate anytime the retained accessory power (RAP) system is active or when the ignition switch is in the ACCY or ON position.
The DDM contains 4 power window switches which are integral components. Closing any of the normally open, rocker type switches provides the DDM with a request for power window operation. The switches for the 2 front windows have 3 positions Up, Down and Express Down, while the switches for the rear windows have only 2 positions, Up and Down. Each of these switches and their positions is a direct input into the DDM. Upon receiving a request for power window operation, the DDM, transmits a class 2 message indicating the switch and it's changed position.
The PDM contains a single power window switch that is an integral component. Closing of this normally open, rocker switch provides the PDM with a request for the front passenger power window operation. The switch for the front passenger window has 2 positions Up and Down. Each of these switch positions is a direct input to the PDM.
The 2 rear passenger doors have there own switches. Each of the switches contain a power window up and down relay. A switch activation alone can control the up and down functions of the rear windows. However the BCM, upon receiving a class 2 message from the DDM, can control the set of relays which will activate the rear window motors.

Jan 10, 2016 | 2004 GMC Envoy

1 Answer

My power seats and only the power windows on right side quit working on my 2007 silverado classic lt1500 I replaced the circuit breakers already and it did not fix the problem


Does you truck have Memory Seats ? There are 2 options of power seat systems available in full size trucks. The first is 6 way driver and passenger power seats without memory. The second is an 8-way driver seat plus 4-way lumbar with memory, heat and optional cool function.
If you replaced the circuit breaker , did you check for B+ voltage at the switch ? If you have memory seats there is a control module that is in the mix.
For the power windows same thing here ,the BCM - body control module is involved .A factory Tech 2 scan tool is still the best tool to use ,checking data parameters .
The switch for the front passenger power window has 2 positions UP and DOWN, and it's position is a direct input into the PDS. Upon receiving a request for power window operation (switch activation), the PDS supplies voltage to the power window motor right front up or down circuit and grounds the opposite and the power window motor runs to drive the window UP or DOWN.
The front passenger power window can also be operated from the driver master control. The front passenger window switch on the driver master control has 2 positions UP and DOWN and it's position is a direct input into the DDS. Upon receiving a request for front passenger power window operation, the DDS transmits a GMLAN message indicating the changed switch position. When the PDS receives this message, the PDS supplies voltage to the power window motor right front up or down circuit and grounds the opposite and the power window motor runs to move the window UP or DOWN.
GMLAN - is a data bus communication network that vehicle modules talk together on.
Rear Passenger Power Window Operation (RPO A31/AN3/DL3)
The body control module (BCM) monitors the window UP/DOWN command from the DDS. When the rear window UP or DOWN command is received, the BCM sends a signal to the appropriate rear window switch. The rear window switches continuously monitor the up and down signal circuits, if no function is being commanded, the signal voltage is at approximately B+ voltage. If the UP or DOWN function is commanded, the BCM signal voltage drops approximately 5 volts and the appropriate rear window switch will then command the window in the UP or DOWN direction.
Your best bet would be to take your truck to a GM dealer !
Your best bet

If

Nov 04, 2015 | Cars & Trucks

1 Answer

I have a saturn ion 06 coupe, neither of my windows are working! I have checked the fuse replaced both motord\regulators and the switches. They're still not working!! Plz help


Please do these check and let me know.

Diagnostic Fault Information

Perform the Diagnostic System Check - Vehicle prior to using this diagnostic procedure.

Circuit/System Description

The power window system will operate any time the ignition is the ACC or RUN position. The power window system will also operate whenever the body control module (BCM) is in retained accessory power (RAP) mode. The driver power window switch contains individual window switches for each of power windows. All windows may be controlled up and down from the driver power window switch. The individual passenger power window switches will only control the up and down operation of their respective power window.
Each power window contains a reversible power window motor. The direction the window travels is dependent upon the polarity of the supply voltage. By reversing polarity of the supply voltage the window motor will move up or down. Each power window motor is internally circuit breaker protected.
Battery voltage is supplied to the power window switch through the accessory voltage supply circuit. The power window switch also receives a constant ground source. The power window motor control circuits are connected to ground through the normally closed up and down contacts of the power window switch. When the power switch is placed in the down position, the power window motor down control circuit is switched to 12 volts and is applied to the down side of the power window motor. Since the other side of the power motor is connected to ground through the normally closed contacts of the up switch, the window travels down. By placing the power window switch in the up position, the polarity of the power window motor is reversed and the window travels up.

Reference Information

Schematic Reference Power Window Schematics
Connector End View Reference Power Door Systems Connector End Views
Description and Operation Power Windows Description and Operation
Electrical Information Reference

Circuit/System Verification

Ignition ON, command the appropriate door window UP and DOWN by pressing the appropriate Window switch. Observe the operation of the appropriate door window.

Circuit/System Testing

  1. Ignition OFF, disconnect the B+ harness connector at the Driver Window Switch.
  2. Ignition OFF, test for less than 1.0 ohm of resistance between the ground circuit terminal D and ground.
  3. ?X If greater than the specified range, test the ground circuit for an open/high resistance.
  4. Ignition ON, verify that a test lamp illuminates between the B+ circuit terminal E and ground.
  5. If the test lamp does not illuminate, test the B+ circuit for an open/high resistance. If the PWR WNDW fuse is open, test the circuit terminal C for a short to ground.
  6. If all circuits test normal, test or replace the Driver Window Switch.
  7. Ignition OFF, connect the harness connector at the Driver Window Switch.
  8. Ignition OFF, disconnect the Passenger Window Switch.
  9. Ignition ON, verify that a test lamp illuminates between the B+ circuit terminal and ground.
  10. ?X If the test lamp does not illuminate, test the B+ circuit for an open/high resistance.
  11. Ignition OFF, test for less than 1.0 ohm of resistance between the control circuit terminal H and ground.
  12. ?X If greater than the specified range, test the control circuit for a short to voltage or an open/high resistance. If the circuit tests normal, replace the Driver Window Switch
  13. Ignition OFF, test for less than 1.0 ohm of resistance between the control circuit terminal D and ground.
  14. ?X If greater than the specified range, test the control circuit for a short to voltage or an open/high resistance. If the circuit tests normal, replace the Driver Window switch
  15. Connect a test lamp between control circuit terminal H and control circuit terminal D.
  16. Ignition ON, command the passenger door window UP and DOWN by pressing the passenger window control on the Driver Window Switch. The test lamp should illuminate during either of the commands.
  17. ?X If the test lamp remains OFF, test for a short to ground or open/high resistance on either control circuit. If all circuits test normal, test or replace the Driver Window Switch.
  18. Ignition OFF, reconnect the Passenger Window Switch.
  19. Ignition OFF, disconnect the harness connector at the appropriate Window Motor.
  20. Ignition OFF, test for less than 1.0 ohm of resistance between the control circuit terminal A and ground.
  21. ?X If greater than the specified range, test the control circuit for a short to voltage or an open/high resistance. If the circuit tests normal, test or replace the appropriate window switch.
  22. Ignition OFF, test for less than 1.0 ohm of resistance between the control circuit terminal B and ground.
  23. ?X If greater than the specified range, test the control circuit for a short to voltage or an open/high resistance. If the circuit tests normal, test or replace the appropriate window switch.
  24. Connect a test lamp between control circuit terminal A and control circuit terminal B.
  25. Ignition ON, command the appropriate window UP and DOWN by pressing the appropriate Window Switch. The test lamp should turn ON when commanding the UP and DOWN states.
  26. ?X If the test lamp remains OFF during either of the commands, test for a short to ground on either control circuit. If all circuits test normal, test or replace the appropriate Window Switch
  27. If all circuits test normal, test or replace the appropriate Window Motor.

Component Testing

    Driver Window Switch
  1. Ignition OFF, disconnect the harness connector at the Driver Window switch.
  2. Test for infinite resistance between the signal terminals A and B and the B+ circuit terminal E with the passenger window switch in the INACTIVE position.
  3. ?X If less than infinite resistance, replace the Driver Window switch.
  4. Test for less than 2 ohms of resistance between the signal terminal A and the B+ circuit terminal E with the passenger window switch in the UP position.
  5. ?X If greater than 2 ohms, replace the Driver Window switch.
  6. Test for less than 2 ohms of resistance between the signal terminal B and the B+ circuit terminal E with the passenger window switch in the DOWN position.
  7. ?X If greater than 2 ohms, replace the Driver Window switch.
  8. Test for infinite resistance between the signal terminals F and H and the B+ circuit terminal E with the driver window switch in the INACTIVE position.
  9. ?X If less than infinite resistance, replace the Driver Window switch.
  10. Test for less than 2 ohms of resistance between the signal terminal F and the B+ circuit terminal E with the driver window switch in the UP position.
  11. ?X If greater than 2 ohms, replace the Driver Window switch.
  12. Test for less than 2 ohms of resistance between the signal terminal H and the B+ circuit terminal E with the driver window switch in the DOWN position.
  13. If greater than 2 ohms, replace the Driver Window switch
    Passenger Window Switch
  1. Ignition OFF, disconnect the harness connector at the Passenger Window switch.
  2. Test for infinite resistance between the signal terminals G and F and the B+ circuit terminal with the switch in the INACTIVE position.
  3. ?X If less than infinite resistance, replace the appropriate passenger Window switch.
  4. Test for less than 2 ohms of resistance between the signal terminal G and the B+ circuit terminal with the switch in the UP position.
  5. ?X If greater than 2 ohms, replace the appropriate passenger Window switch.
  6. Test for less than 2 ohms of resistance between the signal terminal F and the B+ circuit terminal with the switch in the DOWN position.
  7. ?X If greater than 2 ohms, replace the appropriate passenger Window switch.
      Window Motor
    1. Install a 30-amp fused jumper wire between the control terminal A and 12 volts. Momentarily install a jumper wire between the control terminal B and ground. The appropriate Window Motor should perform the UP or DOWN function.
    2. ?X If the function does not perform as specified, replace the appropriate Window Motor.
    3. Reverse the jumper wires; the appropriate Window Motor should perform the DOWN or UP function.
    4. ?X If the function does not perform as specified, replace the appropriate Window Motor

Mar 25, 2015 | 2006 Saturn ION

1 Answer

I need the wiring schematics for driver door panel and all switches in a 2003 Chevy Tahoe. My window won't go down on that side and I'm sure I have a short somewhere because my switch works with all other...


You don't know what your getting into , The door switches have electronic control modules incorporated ,DDM- Driver door module an PDM passenger door module .
The power window system consists of the following components:
?€¢
Driver Door Module (DDM)


?€¢
Passenger Door Module (PDM)


?€¢
Body Control Module (BCM)


?€¢
RR power window switch


?€¢
Window up and window down relays in each of the rear passenger window switches


?€¢
Window lockout switch


?€¢
Reversible power window motors in each of the doors (circuit breaker protected)


?€¢
LT DOOR CB 25A (System power for left windows)


?€¢
RT DOOR CB 25A (System power for right windows)


The DDM contains four power window switches which are integral components. Closing any of the normally open, rocker type switches provides the DDM with a request for power window operation. The switches for the two front windows have three positions UP, Down and Express Down, while the switches for the rear windows have only two positions, UP and Down. Each of these switches and their positions is a direct input into the DDM. Upon receiving a request for power window operation, the DDM, transmits a Class 2 message indicating the switch and it's changed position.
The PDM contains a single power window switch that is an integral component. Closing of this normally open, rocker switch provides the PDM with a request for the front passenger power window operation. The switch for the front passenger window has two positions Up and Down. Each of these switch positions is a direct input to the PDM.
The two rear passenger doors have there own switches. Each of the switches contain a power window up and down relay. A switch activation alone can control the up and down functions of the rear windows. However the BCM, upon receiving a Class 2 message from the DDM, can control the set of relays which will activate the rear window motors.
You need a scan tool to diagnose these systems
Power Window Inoperative - Driver Door

1

Did you perform the Door Systems Diagnostic System Check?
Go to Step 2
Go to Diagnostic System Check - Door Systems

2

Operate the driver power window in the UP and DOWN directions.
Does the driver power window operate properly?
Go to Testing for Intermittent Conditions and Poor Connections in Wiring Systems
Go to Step 3

3

  1. Install a scan tool.
  2. Monitor the driver window status data parameter in the driver door inputs list.
Does the driver window status data parameter display an active state?
Go to Step 11
Go to Step 4

4

  1. Monitor the driver window status data parameter in the driver door module inputs list.
  2. Activate the driver power window switch in the up and down positions.
Does the driver window status data parameter change accordingly?
Go to Step 5
The data link connector (DLC) allows a scan tool to communicate with the class 2 serial data line. The serial data line is the means by which the microprocessor-controlled modules in the vehicle communicate with each other. Once the scan tool is connected to the class 2 serial data line through the DLC, the scan tool can be used to monitor each module for diagnostic purposes and to check for diagnostic trouble codes (DTCs). Class 2 serial data is transmitted on a single wire at an average of 10.4 kbps.

You

Mar 24, 2015 | Cars & Trucks

1 Answer

The passenger, right and left rear windows will not go down when controlled from the drivers master window switch. Any thoughts?


Obviously either there is a loose connection with a wire at a terminal or the wires were mixed up and connected to the wrong terminals.

Jul 18, 2014 | 2007 Land Rover Range Rover Supercharged

1 Answer

04 Lincoln ls passenger front window control module


Might be engaging from the drivers side

May 01, 2014 | 2004 Lincoln LS

1 Answer

My passenger window is stuck in


Not a fuse,Most likely a grounding issue with the switch or maybe switch needs replaced. This is a common problem with power windows and 9 times out of 10 it is in the one on the drivers side even though its the passenger window giving the problem...driver side controls all power supply....may be loose connection. Check that first...hope this helps and if so Please leave a rating on this post..

Aug 14, 2012 | Cars & Trucks

1 Answer

Passenger side window stuck in down position. How


sometimes u can bang on lower door panel while pushing on window up button it may work

Jan 31, 2010 | 1988 Chevrolet C1500

Not finding what you are looking for?
2007 Pontiac Torrent Logo

Related Topics:

26 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pontiac Experts

yadayada
yadayada

Level 3 Expert

75744 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8123 Answers

Are you a Pontiac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...