Question about 2004 Chevrolet Silverado

1 Answer

WIPER PROBLEM DRIVER WIPER STUCK TO WINDSHIELD WHEN I STARTED WIPERS. NOW DRIVER WIPER GOES TOO FAR TOM THE RIGHT.

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 30 Answers

There should be an adjustment where the linkage attached to the motor. Loosen the two nuts and slide the linkage one way or the other an eighth of an inch or so. Snug it back up and check it.

Posted on Dec 26, 2013

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
emissionwiz
  • 76848 Answers

SOURCE: Timing Venture wipers

disconnect the wiper transmission from the motor, then run the motor and turn the motor off with the wiper switch, this will park the motor, re-attach the wiper trans linkage so the wipers are parked/down

Posted on Dec 05, 2008

  • 1 Answer

SOURCE: my driver side windshield wiper

I just solved this problem last night with my '05 Impala, and ultimately the solution was what newton5083 stated above.  Yet, it may also be this (I found it online somewhere):
You have bent or broken the "park tab" on the windshield wiper motor bracket. The correct way to fix this is to remove the wiper arms, wiper linkage and wiper motor from the wiper motor bracket, and install a new bracket.
I just bent the tab back into place a couple times for our daughters 2005 Impala but it kept getting bent down again when they didn't take the time to make sure the wipers were not frozen to the windshield, or tried running the wipers to remove heavy snow on the windshield. So yesterday I fabricated a small piece of metal and bolted that to the bracket in the same place the tab stop was.
If someone wants to access this bracket and tab-
1. Use a ½ inch or 13mm socket & ratchet or wrench to remove nuts on wiper arms.
2. They may make a special tool to remove the arms, I used a screwdriver and hammer to tap bottom of the arm to wedge them apart from the spindle.
3. Two small button-looking clips hold the drivers side cowl cover in place under the windshield. These are two-piece clips, pry up the center, than the outer piece.
4. Unclip the washer hose from cowl cover, than pull out plastic cover.
5. There is a smaller plastic cover with on plastic button head holding that cover in place. Gently pry under that clip to remove that cover.
6. Now you can see the wiper trans and bracket. You should see a small tab on that bracket that looks pushed down and bent or possible a square small hole with some torn off metal where the tab broke off.
7. Remove small plastic cover over the wiper transmission and you can see a small spring-loaded arm underneath the wiper transmission assembly.
8. You need to find something to pry that tab back up so when the wipers are running that spring loaded little arm just snaps past the tab running clockwise. It's when you shut off the wipers that the wiper transmission assembly reverses rotation counter clockwise and the small spring loaded arm underneath hits that tab stop, than the wipers will go all the way down and shut off as they should.
Once that tab stop gets bent out of the way the little spring loaded arm has nothing to stop the wiper transmission assembly so it keeps traveling counter clockwise until some other stop shuts the wipers off straight up on the windshield.

There is a revised bracket part # which is supposed to be more durable, GM part #12368639. Here is a copy of the TSB which points out this problem:
Bulletin No.: 05-08-43-003A
Date: March 10, 2005
TECHNICAL
Subject:
Windshield Wipers Park in Up Position (Replace Windshield Wiper Motor Bracket)
Models:
2005 Chevrolet Impala, Monte Carlo
Supercede:
This bulletin is being revised to make a correction to the Parts Information. Please discard Corporate Bulletin Number 05-08-43-003 (Section 08-Body and Accessories).

Condition
Some customers may comment that the windshield wipers park in the out wipe (vertical) position.
Cause
This condition may be caused by a bent park tab on the windshield wiper motor bracket.

Correction
To correct this condition, replace the wiper motor bracket. It will be necessary to transfer the following parts listed below to the new bracket.
^ Wiper transmission
^ Wiper motor crank arm
^ Wiper motor
1. Remove the windshield wiper motor drive system module.
2. Remove the windshield wiper transmission from the windshield wiper motor bracket.
3. Remove the wiper motor crank arm from the windshield wiper motor.
4. Remove the windshield wiper motor from the bracket.
5. Install the windshield wiper motor to the new bracket.
6. Install the wiper motor crank arm to the windshield wiper motor.
7. Install the windshield wiper transmission to the windshield wiper motor bracket.
8. Install the windshield wiper motor drive system module.

A TSB is not a recall, if vehicle is still under warranty the dealer should be repaired for free. If not, you'll have to pay for the repairs. 

Posted on Jan 08, 2009

  • 1 Answer

SOURCE: Windshield wipers not parking

The problem could be a bent parking pall bracket. This is usually caused when you wipe snow from windshield using the wipers instead of brushing off. You need to remove both wipers and the cover from the drivers side. Remove the cover over the wiper motor assembly (held by a plastic button). On the right side of the wiper mechanism is a small tab (part of the wiper bracket). This tab needs to be straight for the wiper park pall to rest against.Carefully hammer this tab straight (or you may have to replace bracket, big job) Then cycle the wiper and you will see the assembly return to park position. Re-install all parts in reverse order.
Hope this works for you.

Posted on Feb 28, 2009

juncro
  • 467 Answers

SOURCE: Wipers stop in the middle of windshield when turned off

check to make sure the wipers are at its right angle on the vehicle, loose the nuts and place both wipers close to the bottom of the wind screen

Posted on Jul 29, 2009

  • 1 Answer

SOURCE: I have a 2003 Chevy Trailblazer Windshield Wiper problem.

As it turns out, there is a recall On 2002-2003 Chevy Trail Blazer's
Windshield Wiper/washer
NHTSA No. 04V046000
Recall Date: Feb, 4th, 2004
Call your dealer to see if this is still under the recall to be fixed.
RECALL: 2002 - 2003 Chevrolet Trailblazer NHTSA Campaign Number: 04V046000 www.nhtsa.dot.gov
Manufacturer GENERAL MOTORS CORP. Recall Date: FEB 02, 2004 Potential Number Of Units Affected: 581394 Description VISIBILITY:WINDSHIELD WIPER/WASHER Summary CERTAIN SPORT UTILITY VEHICLES HAVE WINDSHIELD WIPER SYSTEMS THAT WILL NOT TURN ON, CEASE OPERATION WHILE IN USE, FAIL TO TURN OFF/ON BY THEMSELVES (MOISTURE SENSITIVE WIPER SYSTEM), OR HAVE CONTINUOUS WINDSHIELD WASHER PUMP OPERATION BECAUSE THE PRESENCE OF WATER WITHIN THE WIPER MODULES CAN EITHER CAUSE A SHORT CIRCUIT OR CAN LEAD TO THE CORROSION OF COMPONENTS WITHIN THE MODULE. Consequence DEPENDING ON THE OCCURRENCE AND WEATHER SITUATION, DRIVER VISIBILITY COULD BE REDUCED, WHICH COULD RESULT IN A CRASH. Remedy DEALERS WILL COVER THE WINDSHIELD WIPER MODULE VENT HOLE WITH A PATCH. ALSO, THE WIPER MOTOR, CIRCUIT BOARD, AND ELECTRICAL CONNECTOR WILL BE INSPECTED TO SIGNS OF WATER INTRUSION AND/OR CORROSION AND BE REPLACED AS REQUIRED. THE RECALL BEGAN JULY 6, 2004. OWNERS SHOULD CONTACT CHEVROLET AT 1-800-630-2438; OLDSMOBILE AT 1-800-630-6537; OR GMC AT 1-866-996-9463.

Posted on Feb 06, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1994 Integra LS 4dr, Wipers range is too far!


remove the wiper arm, and reposition the arm to another position, then try it out to see where it lands. Keep doing that until you find the optimal position. ALSO, On my "teg, the driver's side wiper is 1 inch longer than the passenger side, so be sure you are using the correct length wiper.

Mar 30, 2014 | Acura Integra Cars & Trucks

1 Answer

1999 plymouth voyager van windshield wipers


Either the wiper arms are loose or stripped on the pivots or the wiper linkage is broken. Try tightening the arm to pivot bolt. If that doesn't work, remove the plastic cowling and examine the linkage. You can buy new linkage for it.

Sep 23, 2017 | Cars & Trucks

1 Answer

1998 Porsche Boxster windshiled wiper stopped working


Could be loose wiper arm. Are the blades heavy. Too big of wiper blade will cause problems

Nov 15, 2012 | 1998 Porsche Boxster

1 Answer

How To Install Replace Windshield Wiper motor on a Honda Odyssey


Put the right side wiper on only. Turn on wipers. When the wiper moves all the way to the left and starts to go back to the right turn off the ignition with the wiper switch still on. Remove the right wiper arm and install the left wiper arm in the far left of the wiper movement. Turn on ignition and allow the left wiper to go all the way back to it's rest location at the bottom of the windshield. Turn off ignition and install the right side wiper arm. This will give you a start to properly set the wiper arms.

Apr 12, 2012 | 2003 Honda Odyssey

1 Answer

Driver side windshield wiper


Hi check if the nut is is tight on the wiper handle to the linkage and also check that it did not strip before tightening good luck

Sep 02, 2009 | 2005 Saturn ION

1 Answer

Windshield wipers won't work right


The windsheild wiper relay might be stuck or broken. Try tapping it with something or replace it. Could also be the the switch (lever that you control the wipers with) i hope this helps and good luck with diagnosing your problem.

Feb 21, 2009 | Ford Taurus Cars & Trucks

1 Answer

Wipers on 2000 Jeep Cherokee travel too far


hello, this sounds like your wiper transmission got out of alignment possibly due to ice on windsheild.don't really know.short of replacing you could loosen the nut under the cover and move wiper arm back possibly.

Jan 25, 2009 | 2000 Jeep Grand Cherokee

2 Answers

Windshield wipers not parking


The problem could be a bent parking pall bracket. This is usually caused when you wipe snow from windshield using the wipers instead of brushing off. You need to remove both wipers and the cover from the drivers side. Remove the cover over the wiper motor assembly (held by a plastic button). On the right side of the wiper mechanism is a small tab (part of the wiper bracket). This tab needs to be straight for the wiper park pall to rest against.Carefully hammer this tab straight (or you may have to replace bracket, big job) Then cycle the wiper and you will see the assembly return to park position. Re-install all parts in reverse order.
Hope this works for you.

Jan 15, 2009 | 2003 Chevrolet Impala

1 Answer

Windshield wiper


Is there a little cap covering where it attaches to pivot at base of windshield. If so, pry/flip it up, forward from bottom or end, & you'll probably see a nut to tighten underneath it. Do it when wipers off & in parked position so you can move the arm where you remember it goes, then tighten. Don't reef too ******* it, they aren't that strong and will snap if you go too far with wrench, just real snug. Unless you've stripped spline real good, this should do it.

Dec 21, 2008 | 2001 Hyundai Elantra

Not finding what you are looking for?
2004 Chevrolet Silverado Logo

66 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76848 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...