Question about 2004 Nissan Quest

1 Answer

Check engine,tcs and slip light are on?

I got a code for bank 1 cam shaft sensors i have replaced both and crank shaft position sensor the lights came back on i have full engine power but every now and then i have problems starting my van, what else could be wrong?

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 94 Answers

A lot of vehicles have special tools that are needed to install the Camshaft Position Sensors. Where if you don't have the tools you can still put the sensor in but it might not be installed correctly. Also double check to make sure that the Crank Sensor is still tightly secured.

Posted on Dec 26, 2013

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

NismoMaster
  • 146 Answers

SOURCE: no heat sensor 1 bank 1 did back probe is there a relay or fuse

There is a fuse (fuse #4) for the heated O2 sensor. Make sure the fuse is good and that there is not an open circuit to the power source.

Posted on Jul 26, 2009

jimmybrown67
  • 835 Answers

SOURCE: 1st error: p0136 oxygen sensor circuit bank 1

around 300.00 -400.00 est. at dealer garage maybe little cheaper not much more

Posted on Nov 02, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

P0016 and P0017 check engine pop up after i run for 10 to 15 miles?


the common causes for code P0017 are as follows:
  • A faulty cam or crank sensor
  • The cam or crank circuit is open or shorted
  • The timing belt/chain is out of time
  • The cam or crank tone ring is slipped/broken
  • A problem in the VVT system P0016 Crankshaft Position - Camshaft Position Correlation (Bank 1 Sensor A) P0017 Crankshaft Position - Camshaft Position Correlation (Bank 1 Sensor) God Bless! Hope this helps you.

Mar 08, 2016 | Cars & Trucks

1 Answer

03 Chevy 2500HD 6.0 Gas I have no power to the 10A fuse for the crank with the key on or off truck does start. A P0342 code keep coming up


code p0342 refers to cam shaft position (CMP) sensor A bank 1 --low input===causes--wiring short to ground---CMP sensor---ECM
Check for wiring shorting out on the engine /body, replace the cam sensor on bank 1

Jan 31, 2015 | Cars & Trucks

2 Answers

Pcm?


PCM= Powertrain Control Module. It is the brains of the car, it reads the sensor in put from all sensors including the cam shaft position sensor

May 14, 2014 | 2004 Toyota 4Runner

1 Answer

What else could be the problem?


did you reset the light after change of sensers as some require reset to come out of limp mode

Dec 26, 2013 | 2004 Nissan Quest

1 Answer

Tcs light flashes and p0340 code


P0340 code means "Something" is wrong in the timing...
from CMP (Camshaft Position sensor) to the crankshaft bolt.

Very first thing, verify connectors are clean and shiny.
clear all codes, even hard codes.

57f2e883-ce32-4061-b04b-ae0890f2c653.gif
612c4a6c-208f-43b8-8645-8318e85f9e48.gif
9e0c3051-1208-49b3-95d5-de3ff545fd3a.gif

Nov 23, 2013 | 2005 Mazda 6

1 Answer

Camshaft position sensor correlation bank 1 code


timing belt is off by a tooth or two. you probably didn\'t have to replace the coolant sensor; that code sets whenever the sensor is disconnected and the ignition is turned on; and it needs to be reset by disconnecting the battery or with a code reader. anyway, the crank/ cam sensors are out of sync. if you\'ve got the twin cam engine, they are a royal pain to get the belt to lay properly on the two cams.

Apr 15, 2013 | 2007 Chrysler PT Cruiser Touring Hatchback

1 Answer

I have the code p0340 for slip n tcs is telling me is a sensor but it show2


I am not sure what "slip n tcs" means but on the 2005 nissan maxima the code P0340 is for the camshaft position sensor circit on bank 1, which is in the rear of the engine compartment. Code P0345 is for camshaft position on bank 2, which is in the front of the engine compartment. The images show the Cyl banks and a cam sensor.6_29_2012_3_38_07_am.gif6_29_2012_3_40_48_am.gif

Jun 29, 2012 | 2005 Nissan Maxima

1 Answer

I have 2008 Dodge Caliber and the engine light came on with codes P0017 Crank Shaft Position Cam Shaft Position Correlation - Bank 1 Sensor B can you tell me what this means as i cannot afford to...


Sounds like your crank sensor or cam sensor is malfunctioning. Their positions are not correlating which means they are not in perfect alignment according to the computer. I don't think the parts are very expensive and probably not that hard to replace. I replaced both on my 99 Ford Explorer, and I don't recall it that difficult. Anyway, hope this helps.

Mar 17, 2011 | Dodge Caliber Cars & Trucks

2 Answers

05 kia amanti with diagnostics codes p0350,p0320,p0300,p0302,p0303,p0304,p0305,p0306.skipping at times.when it does skip & misfire the rpm gauge goes crazy.this problem is not consitant


Generic OBD II Diagnostic Trouble Codes

DTC CODES P0300 to P0399

P0300....Random/Multiple Cylinder Misfire Detected

P0301....Cylinder 1 Misfire Detected

P0302....Cylinder 2 Misfire Detected

P0303....Cylinder 3 Misfire Detected

P0304....Cylinder 4 Misfire Detected

P0305....Cylinder 5 Misfire Detected

P0306....Cylinder 6 Misfire Detected

P0307....Cylinder 7 Misfire Detected

P0308....Cylinder 8 Misfire Detected

P0309....Cylinder 9 Misfire Detected

P0310....Cylinder 10....Misfire Detected

P0311....Cylinder 11 Misfire Detected

P0312....Cylinder 12 Misfire Detected

P0313....Misfire Detected with Low Fuel

P0314....Single Cylinder Misfire (Cylinder not Specified)

P0320....Ignition/Distributor Engine Speed Input Circuit

P0321....Ignition/Distributor Engine Speed Input Circuit Range/Performance

P0322....Ignition/Distributor Engine Speed Input Circuit No Signal

P0323....Ignition/Distributor Engine Speed Input Circuit Intermittent

P0324....Knock Control System Error

P0325....Knock Sensor 1 Circuit (Bank 1 or Single Sensor)

P0326....Knock Sensor 1 Circuit Range/Performance (Bank 1 or Single Sensor)

P0327....Knock Sensor 1 Circuit Low Input (Bank 1 or Single Sensor)

P0328....Knock Sensor 1 Circuit High Input (Bank 1 or Single Sensor)

P0329....Knock Sensor 1 Circuit Input Intermittent (Bank 1 or Single Sensor)

P0330....Knock Sensor 2 Circuit (Bank 2)

P0331....Knock Sensor 2 Circuit Range/Performance (Bank 2)

P0332....Knock Sensor 2 Circuit Low Input (Bank 2)

P0333....Knock Sensor 2 Circuit High Input (Bank 2)

P0334....Knock Sensor 2 Circuit Input Intermittent (Bank 2)

P0335....Crankshaft Position Sensor A Circuit

P0336....Crankshaft Position Sensor A Circuit Range/Performance

P0337....Crankshaft Position Sensor A Circuit Low Input

P0338....Crankshaft Position Sensor A Circuit High Input

P0339....Crankshaft Position Sensor A Circuit Intermittent

P0340....Camshaft Position Sensor 'A' Circuit (Bank 1 or Single Sensor)

P0341 Camshaft Position Sensor 'A' Circuit Range/Performance (Bank 1 or Single Sensor)

P0342....Camshaft Position Sensor 'A' Circuit Low Input (Bank 1 or Single Sensor)

P0343....Camshaft Position Sensor 'A' Circuit High Input (Bank 1 or Single Sensor)

P0344....Camshaft Position Sensor 'A' Circuit Intermittent (Bank 1 or Single Sensor)

P0345....Camshaft Position Sensor 'A' Circuit (Bank 2)

P0346....Camshaft Position Sensor 'A' Circuit Range/Performance (Bank 2)

P0347....Camshaft Position Sensor 'A' Circuit Low Input (Bank 2)

P0348....Camshaft Position Sensor 'A' Circuit High Input (Bank 2)

P0349....Camshaft Position Sensor 'A' Circuit Intermittent (Bank 2)

P0350....Ignition Coil Primary/Secondary Circuit

Nov 17, 2010 | Kia Amanti Cars & Trucks

2 Answers

Toyota ipsum 2002 check light comes on with code P1346.


Definition of Diagnostic Trouble Code P1346 Audi: Ignition Coil Power Output Stage 3 Short to B+ BMW: Misfire During Start Cylinder 3 Buick: Intake Camshaft Position [CMP] Sensor System Performance Cadillac: Intake Camshaft Position [CMP] Sensor System Performance Chevrolet: Intake Camshaft Position [CMP] Sensor System Performance Ford: Fuel Level Sensor B Circuit GMC: Intake Camshaft Position [CMP] Sensor System Performance Lexus: VVT Sensor Rang/Performance Problem (Bank 1) Lincoln: Fuel Level Sensor B Circuit Mazda: Fuel Level Sensor B Circuit Mercury: Fuel Level Sensor B Circuit Oldsmobile: Intake Camshaft Position [CMP] Sensor System Performance Pontiac: Intake Camshaft Position [CMP] Sensor System Performance Saturn: Intake Camshaft Position [CMP] Sensor System Performance Toyota: VVT Sensor /Camshaft Position Sensor Circuit Range/ Performance Problem (Bank 1) Volkswagen: Ignition Coil Power Output Stage 3 Short to B+

Mar 12, 2010 | 2001 Toyota Sienna

Not finding what you are looking for?
2004 Nissan Quest Logo

188 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

726 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...