Question about Cars & Trucks

Open Question

1987 toyota pickup oil pressure sending unit wiring


Posted by Anonymous on

6 Suggested Answers

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

  • 233 Answers

SOURCE: 1994 toyota 22re 4x4 pickup fuel injector wiring diagram

the color of the plastic plug does not matter... You will have two injector plugs with white/red and yellow wires - those two go to cyl#'s 1 and 3.
the other two plugs will have white and blur wires.. those two plugs go to injectors # 2 and 4.

Posted on Jan 14, 2009

  • 78 Answers

SOURCE: oil pressure sending unit

Hi there;

Your looking foer the oil pressure sensor on the 2004 8.1L.
You will find it located directly behind the EGR valve threaded into the block just to the drivers side of the center bolt for the transmission to block connection.


Posted on Mar 17, 2009

  • 1 Answer

SOURCE: 01 grand cherokee fan relay/oil pressure

I don't know if this will help anyone, but i had a issue with my jeep running hot and check engine light coming on as well. After alot of trips to different shops - the last one found that there were two senors in the engine for the fan that need to be changed. Everyone would aways fine the one up top but not the second one. After that, have not had any other problems like it since.

Posted on Mar 23, 2009

  • 323 Answers

SOURCE: Oil sender not working, Location

The oil sender is at the back of the engine beside the distributor.

Posted on Apr 28, 2009

  • 1050 Answers

SOURCE: Buick Regal dying

You have a problem in the fuel pump relay circuit for sure then. I'm betting the relay, but it could be that dropping resistor.

Posted on May 11, 2009

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

87 Toyota pickup 22r M/t Starter relay wire connector diagram 28300-35010

Visit the on-line store, know as reliable-store, they have the repair manuals. I'm sure you will get the solution of your problem.
1987 Toyota Pickup Workshop Service Manual

Dec 27, 2016 | Toyota Cars & Trucks

1 Answer

Starter relay gone bad on my 90 toyota, have a new 12 volt, four point 30 amp univerisale relay with numbers reading 85,86,87,30..what color of wire goes to number on relay?

If you look at the relay it has a wiring diagram on the side of it, showing the power wires (recall 87 being one of them) and the control wires. Can't tell you color, perhaps a Toyota tech could but in my experience they vary.

Nov 22, 2013 | 1990 Toyota Pickup

1 Answer

When cold, my 87 camry puts out 60-65 psi oil pressure. After it heats up, this pressure drops to 15psi and the oil light comes on. There is only about 70,000 miles on a rebuild with a new oil pump. C

If the sending unit is working correctly, I would say the oil pump or engine is failing.
You can replace the sending unit or have the oil pressure checked with a mechanical gauge to verify.
Its also possible the engine oil is being diluted by gasoline or other liquids.

Aug 31, 2012 | 1987 Toyota Camry

1 Answer

Need wiring diagram for radio on 87 toyota pickup


Hope help (remember comment and rated this post).

Apr 12, 2010 | 1987 Toyota Pickup

2 Answers

My gas gauge goes to full when i fill it up but in the middle of driveing 60 miles it always falls to empty and stays there theres no inbetween help please......... this problem is on my 87 toyota 4x4...

The fuel sending unit in the tank is going bad,it is a float,and it is failing,to repair,it must be replaced,removal of the tank is required.

Mar 14, 2010 | 1987 Toyota Pickup

1 Answer

I need to find the wiring that goes to the oil pressure sensor on a 1993 Chevrolet Silverado diesel pickup that has been converted to gas. Where do I find a schematic of this? When the pickup was converted...

Take all remaining wires and "flash" them to a good ground with the ignition on. when you find the one that makes the oil pressure gauge move, that's your wire. Do not make a solid connection when doing this or you can damage systems served by the "wrong" wires. First look for the wire near the sending unit location...generally the wire leads coming out of the main harness are not very long. The problem with most schematics is that often they get the color wrong or they tell you a wire is there but don't say where "where" is. Also, if a fuse blows when flashing the wires, make a note of what wire went to that fuse (system) it will help with later wiring.

Aug 02, 2009 | 1991 Chevrolet Silverado 2500

2 Answers

New fuel pump wont work either

Look under hood some ware around left fender well there should be a red wire with a plug on it that looks like it should be pluged to something but its not, that wire goes directly to fuel pump, run a hot lead to that and see if pump runs. Also chk. grounds and hot leads and all fuses and the relay. If you can't find the wire, and your sure fuses and relay and connections are functioning, you may have to run your own hot wire to pump to see if it will run. Be aware its possible to have gotten a defective pump.

Feb 17, 2009 | 1987 Chevrolet S-10 Pickup

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

49 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts


Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides