Question about Cars & Trucks

1 Answer

Suzuki baleno no spark

Car have no spark and i check camshaft sensor,crankshaft sensor,bobine coils,immobiliser,fuses,releys and everyithing is ok what to do next

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Cars & Trucks Master
  • 44,657 Answers

Did you check to see if the cam shaft is turning ( broken timing belt)

Posted on Dec 27, 2013

Ad

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: 97 intrepid no spark replaced coil checked all

Check the starter...it is on the battery side by the manifold and autozone will do a free test. if thats not it, check if there is a fuze on the wire to to starter...and if that isn't it then it could be your ignition switch

Posted on May 17, 2009

  • 14036 Answers

SOURCE: 1997 Dodge Ram 1500 5.9 gas v8 engine. Lost Fire,

you have pcm problems or ASD relay problems.they both control the fuel and ignition.

Posted on Jun 05, 2009

johnjohn2
  • 5763 Answers

SOURCE: 2006 suzuki swift immobiliser light flashing and car not starting what can i do to fix it?

You may have a bad key chip, try a diffrent key in the ignition, also make sure you do not have magnet strip mini swipe cards on key chain near the ignition. this sounds like the immoboilizer system is active. this system will not allow the coils to spark.
The key would be the first thing to check. do this by using another key.if car still will not start then the key reader may be bad, this is located around the ignition . the last problem could be the module or a broken wire.The best way to check this would be with a scan tool. there will be codes stored in the anti or body module. the codes will tell you where the failure is and with some testing the problem can be found. the scan tool can help by reading the values and readings. it can tell you if the key chip is read and if the module accepts it. i think if the spare key does not start the car then it will be cheaper to have a shop diagnose the problem. this will help you from just putting parts in. also this anti theft system needs programing when certain parts are replaced.
hope this is helpful, good day

Posted on Apr 22, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

No spark from 1 ign coil on suzuki baleno 1.6


wow , no year, but did show G16 engines.
Grand, is a clue. but is not.
wiki facts: so what country is your car, we are USA here,
and we have not one Baleno here.
the Suzuki Baleno throughout Asia, Australasia, and Europe. In India where it was manufactured by Maruti Suzuki, the Cultus Crescent was sold as the Maruti Baleno

Ive not seen Every version of every G16 engine suzuki made
world wide, only OURS.

1995 to 2007
my wild guess, is your ECU is OBD1 ecu, (do you know?)
and as such, there are no scan tools so only the CEL blink codes
work.
No spark 5 places, 4 sparks dead and coil HV tower term dead.
here is the checks. for all early G16
  1. fuses good, IG-coil and "FI"????
  2. key on head lights work, good turn them off.
  3. keyon CEL glows, (not blinks) if dead fuse blown, if flashing Immobilizer is UNHAPPY.
  4. CEL glows you crank, its lost spark and all ecu cut fuel no spark.
  5. So you insert the diagnostic jumper wire. in the the DLC connnecter under hood and CEL flashes 41 or 42 DTC or?
  6. bingo? code 12 is happy code.
  7. crank for 5 full seconds to see the cause code.
here is the OBD1 year, way to get flash codes
USA until 1995
and outside USA up to 2001 or more.

http://www.fixkick.com/CEL/CEL.html#OBD1codes

no year, makes this very hard,
and no country x10 that. (fueling and spark system vary by COUNTRY !

Jul 08, 2014 | Suzuki Grand Vitara Cars & Trucks

1 Answer

2008 PT Crusier will not start. The coil is not sending power to the spark plugs. Brand New Coil, all fuses are good. New Camshaft sensor.... Still hunting the problem, any suggestions....


check that the immobiliser is operational. Check that power is getting to the coil ( ign fuse ). Check power from run position on the ignition switch to coil.

Apr 19, 2014 | 2008 Chrysler Pt Cruiser

1 Answer

Car have no spark suzuki baleno 1.6 L


fuel pump..auto shutoff relay..

Dec 26, 2013 | Cars & Trucks

1 Answer

Car have no spark I check crank sensor,camshaft sensor,bobine,fuses and everything is ok what can be a problem


check immobiliser operation. run fault codes . check ignition fusible link near the battery

Dec 26, 2013 | 1996 Suzuki Esteem

1 Answer

2003 dodge stratus has no spark. already replaced coil pak


CHECK IGNITION COIL FUSE.IF FUSE OKAY.YOU REPLACED COIL POWER TRANSISTOR. OTHER POSSIBLE CAUSES YOU NOT GETTING SPARK COULD BE FAULTY CAMSHAFT SENSOR AND CRANKSHAFT SENSOR ALSO FAULTY PCM.BEST TO CODE SCAN CAR BEFORE BUYING NEW PARTS.

May 03, 2011 | Dodge Stratus Cars & Trucks

2 Answers

I have a 93 dodge caravan van that wont start it wants to turn over but won't.


For an engine to run, you need three things to happen inside the engine, compression, fuel and ignition, without any one of these components the engine will not run.
  • Compression - Engine compression caused by crankshaft rotation and pistons moving up and down inside the engine block. If the timing belt or timing chain fails it will cause the camshaft to become out of correlation with the crankshaft or allow the camshaft to stop rotating. Either of these conditions will cause the engine to lose compression and sometimes cause internal engine damage.
  • Fuel Delivery System - The fuel system includes: fuel pump, fuel injectors, pressure regulator, fuel filter and pressure lines. This system is used to supply fuel under pressure to the fuel injection system, the lack of fuel pressure or volume will cause the fuel delivery system to fail and the engine to stall or not start.
  • Ignition Spark Delivery System - The ignition system components include: spark plugs, spark plug wires, distributor (if applicable), crankshaft angle sensor, camshaft angle sensor, ignition coil, ignition module, knock sensor and ECM (engine control module). The engine relies on the ignition spark to be delivered to the combustion camber at the correct time. If the ignition spark stops or is delivered at the wrong time the engine will not run or run poorly.
If Your Engine Cranks but Does Not Start Follow this Troubleshooting Guide
Most vehicles operate by the same principle; basic troubleshooting procedures apply to most cars.
  • Step 1: Anytime you have a problem with electronically controlled components such as an engine, transmission, ABS brake, or SRS (supplemental restraint system, Air Bag) inspect all fuses using a test light and check the under hood power distribution center and under dash fuse panels. If all fuses test ok continue to the next step.
  • Step 2: To check for problems with electronically controlled components such as an engine, transmission, ABS brake, or SRS (supplemental restraint system, Air Bag) and the fuses test ok a trouble code scan is needed to identify any system trouble. Use a simple scanner tool to retrieve trouble codes and see if they relate to the specific problem, like a crank angle sensor failure code. If the trouble code present does not pertain to the immediate problem like an EVAP code ignore it until a later time, after the car is running. The reason we repair non-related codes after the engine is running is because sometime false codes can be triggered by the engine not running. Once the engine is running again the code present might cycle and turn itself off. You might say "if the engine doesn't run shouldn't it have a trouble code?" Sometimes conditions occur that will not be detected by the computer, example: if the fuel pump fails the computer cannot detect the failure, so the engine doesn't start and the computer thinks everything is ok with no codes. If no trouble codes are present proceed to the next step.
poster.jpg?1292981965 Scan for Trouble Codes
  • Step 3: The spark plugs in your engine are used to ignite the compressed fuel air mixture. If the condition of the spark plugs are fouled by excessive fuel or carbon the engine will not start, backfire or run rough. Remove all spark plugs to inspect their condition. Please use this spark plug condition reference guide to see how the spark plugs are operating.
  • Step 4: Determine if the engine has compression, this can be done a number of ways but the most complete method is to perform a compression check. Remove the spark plugs and perform a compression test on one cylinder. If one cylinder has compression then the remaining cylinders usually will be close to the same. Crank the engine over about 5 seconds, normal compression readings should be between 125 psi and 160 psi on each cylinder. If no or little compression exists additional tests will be needed. The most common reason for an engine to lose compression is a timing belt or timing chain failure. If low or no compression exists remove the oil fill cap and observe camshaft rotation when the engine is cranked over. If no rotation exists the timing belt or chain has failed. If your engine has a timing belt and you cannot see the camshaft easily remove the upper bolts to the timing cover and gain visual access to the belt, recheck cam rotation by cranking the engine over. Sometimes a timing belt or chain can jump causing the camshaft to lose correlation with the crankshaft and therefore causing low compression. The best test for this condition is to remove the timing belt/chain cover and inspect timing marks. If the compression is ok proceed to next step.
  • Step 5: Test the ignition system output, ignition systems can vary in configuration but operate on the same principal. Ignition systems can consist of a coil, pick up coil, crank angle sensor, cam angle sensor, spark plugs, spark plug wires, distributor cap, ignition rotor and a distributor and any variations of these components. An ignition coil is a voltage stepper coil that transforms a low voltage (12 volts) signal into tens of thousands of volts needed to jump the gap of the spark plug. This coil is activated by an ignition module triggered by using the camshaft/crankshaft angle sensor; timing is adjusted by the ECM (computer).
    This primary electrical signal is generated by the ECM which calculates spark timing by using a variety of sensors including coolant temperature, mass air flow, and oxygen sensors. To perform a basic ignition output test you must have a test light and follow this ignition system output test video.
    crank_trigger_ignition_system.jpg
    Distributor less Ignition System Configuration
    Some ignition systems have a coil for each spark plug. This is called Direct Ignition (DI) system; there are no plug wires in this system just individually controlled ignition coils. The amount of coils or spark plugs depend on the number of cylinders the engine is designed with, example: four cylinders, six cylinders etc. To perform a basic ignition output test you must have a test light follow this ignition system output test video and substitute the ignition coil for the plug wire (Note: leave the coil trigger wires connected).
    coil_over_plug.jpg
    Coil Over Spark Plug
    If the ignition system test is weak or non-existent test the car fuses, both under hood power distribution center and the fuse panel under dash. This test is performed with a test light tool. The test light should illuminate on both sides of the fuse, if not the fuse has failed and needs to be replaced. If the fuses are ok a manufacturer specific repair procedure is required and an online auto repair manual is needed to continue. If the ignition system tests ok proceed to the next step.
poster.jpg?1292969781 Test Ignition System Video

Jan 12, 2011 | 1993 Dodge Caravan

3 Answers

The engine turnes but it wont start.


Free Auto Repair Advice by Professional Mechanics




Troubleshooting / Car Engine Cranks but Will Not Start / Engine Crank But Wont Start 2

* Why does my engine stall at idle?
* How do I change my spark plugs?
* Why does my engine stall?
* Why does the engine stall after replacing the battery?
* Why won't my engine crank over?
* How to retrieve trouble codes
* How to test fuel delivery system
* Engine cranks excessively
* Engine has excessive smoke
* Rapid ticking sounds when engine is cranked
* How to tune up your engine
* How to jump start your engine
* How to test an oxygen sensor
* How to open a car hood
* How a flywheel - flex plate works

Engine Cranks But Will Not Start

For an engine to run, you need three things to happen inside the engine, compression, fuel and ignition, without any one of these components the engine will not run. Follow the repair guide below:


Engine Configuration with Camshaft Operation

*

Compression - Engine compression caused by crankshaft rotation and pistons moving up and down inside the engine block. If the timing belt or timing chain fails it will cause the camshaft to become out of correlation with the crankshaft or allow the camshaft to stop rotating. Either of these conditions will cause the engine to lose compression and sometimes cause internal engine damage.
*

Fuel Delivery System - The fuel system includes: fuel pump, fuel injectors, pressure regulator, fuel filter and pressure lines. This system is used to supply fuel under pressure to the fuel injection system, the lack of fuel pressure or volume will cause the fuel delivery system to fail and the engine to stall or not start.
*

Ignition Spark Delivery System - The ignition system components include: spark plugs, spark plug wires, distributor (if applicable), crankshaft angle sensor, camshaft angle sensor, ignition coil, ignition module, knock sensor and PCM (engine control module). The engine relies on the ignition spark to be delivered to the combustion camber at the correct time. If the ignition spark stops or is delivered at the wrong time the engine will not run or run poorly.

If your engine cranks but does not start follow this troubleshooting guide:
* Step 1 - Anytime you have a problem with electronically controlled components such as an engine, transmission, ABS brake, or SRS (supplemental restraint system, Air Bag) inspect all fuses using a test light and check the under hood power distribution center and under dash fuse panels. If all fuses test ok continue to the next step.
* Step 2 - To check for problems with electronically controlled components such as an engine, transmission, ABS brake, or SRS (supplemental restraint system, Air Bag) and the fuses test ok a trouble code scan is needed to identify any system trouble. Use a simple scanner tool to retrieve trouble codes and see if they relate to the specific problem, like a crank angle sensor failure code. If the trouble code present does not pertain to the immediate problem like an EVAP code ignore it until a later time, after the car is running. The reason we repair non-related codes after the engine is running is because sometime false codes can be triggered by the engine not running. Once the engine is running again the code present might cycle and turn itself off. You might say "if the engine doesn't run shouldn't it have a trouble code?" Sometimes conditions occur that will not be detected by the computer, example: if the fuel pump fails the computer cannot detect the failure, so the engine doesn't start and the computer thinks everything is ok with no codes. If no trouble codes are present proceed to the next step.
* Step 3 - The spark plugs in your engine are used to ignite the compressed fuel air mixture. If the condition of the spark plugs are fouled by excessive fuel or carbon the engine will not start, backfire or run rough. Remove all spark plugs to inspect their condition. Please use this spark plug condition reference guide to see how the spark plugs are operating.
* Step 4 - Determine if the engine has compression, this can be done a number of ways but the most complete method is to perform a compression check. Remove the spark plugs and perform a compression test on one cylinder. If one cylinder has compression then the remaining cylinders usually will be close to the same. Crank the engine over about 5 seconds, normal compression readings should be between 125 psi and 160 psi on each cylinder. If no or little compression exists additional tests will be needed. The most common reason for an engine to lose compression is a timing belt or timing chain failure. If low or no compression exists remove the oil fill cap and observe camshaft rotation when the engine is cranked over. If no rotation exists the timing belt or chain has failed. If your engine has a timing belt and you cannot see the camshaft easily remove the upper bolts to the timing cover and gain visual access to the belt, recheck cam rotation by cranking the engine over. Sometimes a timing belt or chain can jump causing the camshaft to lose correlation with the crankshaft and therefore causing low compression. The best test for this condition is to remove the timing belt/chain cover and inspect timing marks. If the compression is ok proceed to next step.
* Step 5 - Test the ignition system output, ignition systems can vary in configuration but operate on the same principal. Ignition systems can consist of a coil, pick up coil, crank angle sensor, cam angle sensor, spark plugs, spark plug wires, distributor cap, ignition rotor and a distributor and any variations of these components. An ignition coil is a voltage stepper coil that transforms a low voltage (12 volts) signal into tens of thousands of volts needed to jump the gap of the spark plug. This coil is activated by an ignition module triggered by using the camshaft/crankshaft angle sensor; timing is adjusted by the ECM (computer).

Hope helps (remember rated and comment this).

Aug 11, 2010 | 1999 Chevrolet Blazer

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

152 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76691 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...