Question about 2007 Toyota RAV4

Open Question

Need to remove parking sensor fuse

Parking sensors are permanently on.

Posted by Anonymous on

Ad

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
  • 318 Answers

SOURCE: 1992 camery

The module reads the bulb amperages, so the bulbs must be the right ones for the car. Pay close attention to the third light and its brightness....921 I believe

Posted on Jun 07, 2009

Ad
  • 1348 Answers

SOURCE: i have a 2005 toyota tundra with rear parking

check the fuse for that circuit.there is a beeper under the dash as well.put a test light on it and see if it flashes,that means the beeper is dead.remove the switch if there is one that turns it off and jumper across it,and check the circuit from the shifter wiring to it,and also the reverse lights,they may have it wired to the reverse lights.

Posted on Apr 26, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where to find fuse for relation of the reverse parking sensors in kia sedona ls 07plate


kia sportage parking sensor - ABMforum.com

abmforum.com/kia-sportage-parking-sensor.html
kia sportage parking sensor installing rear parking sensors fitting rear parking sensor strip ... the pre-drill hole on 07 sportage 2007 kia sportage lx navigation wiringparking sensors. ... I cannot see any fuse which may relate to them. ... with their rear parking sensors Even if all is clear behind I now get a continuous beep and ...

Urgent help needed - towbar electrics - Kia Forum

www.kia-forums.com/kia.../71610-urgent-help-needed-towbar-electrics....

Aug 28, 2011 - 10 posts - ‎3 authors
I'm in the middle of fitting a genuine Kia towbar (made by Witter) to my SW. ... Need help again - Does anyone know the location of the PDC Control unit (parking sensors)? ... Drives: Kia Ceed SW 1.6 MT LX A8 ... with the loom which connects to the fuse box does not seem to attach to the rear lighting loom.

[PDF]2007 Sedona Owner's Manual - Kia Canada


Jan 30, 2016 | Kia Cars & Trucks

1 Answer

What is the fuse labeled on the fuse box for park assist for 2011 chevy traverse


Parking Assist Control Module Parking Assist Distance Sensor

Parking Assist Warning Indicator

These are the components for your parking assist the fuse you are looking for is the ECM / PCM this is the main computer for the car if i had more info on ur problem I might be able to help you more




Apr 08, 2014 | 2011 Chevrolet Traverse 1LT

1 Answer

2002 yukon parking assist quit working


{: ) I wonder what quit do you mean? But anyway, there are certain conditions that can disable your park assist temporarily, like the park brakes on, park assist switch disable on, an object is attached to the rear of the vehicle, dirty sensors, overspeed, speed sensors malfunction and more.
If ever one of your sensors are not working, or maybe a module or wiring problem, then it can permanently disable the park assist system, unless the problem is quickly addressed.
The most practical and fast way of tracing the cause is to use a scan tool. It will read all the codes and datas that are relevant to the problem, it can also tell which of the four sensors are at fault, thereby reducing the time of guessing.
For the moment, you can check the VEH B/U fuse 10amp at the underhood fuseblock, and IGN 1 fuse 10amps at the IP fuseblock. Goodluck.

Jul 22, 2011 | 2002 GMC Yukon XL

1 Answer

How do I get the rear spindle off so I can replace the emergency brake shoes on my 2006 chrysler pacifica?



Adjustment

  1. Place parking brake lever in -full released- position.
  2. Raise and support vehicle.
  3. Remove plug in parking brake shoe support to access adjuster star-wheel.
  4. Through the access hole, rotate the adjuster star wheel in the following direction to expand the shoes outward against the drum:
    1. Left brake - Rotate star-wheel toward rear of vehicle.
    2. Right brake - Rotate star-wheel toward front of vehicle.
  5. Using an appropriate tool, turn adjuster star wheel until wheel will not rotate (dead lock).
  6. Back off adjuster six detents (teeth).
  7. Rotate wheel, checking for light drag. If drag is too heavy, continue to back off adjuster one detent at a time until light drag is present. Do not back off star-wheel more than 17 detents from wheel lock.
  8. Install access plug.
  9. Adjust opposite wheel parking brake shoes using same method.
  10. Lower vehicle.
  11. Apply and release parking brake lever once to ensure proper operation of parking brakes.


Removal & Installation NOTE The following procedure may be used to remove shoes on either side of the vehicle.

  1. Lock out automatic adjuster in parking brake lever.
  2. Raise and support vehicle.
  3. Access and remove rear hub and bearing.
  4. Remove parking brake cable bolt at knuckle.
  5. Completely back off parking brake shoe adjustment.
  6. Remove parking brake shoe adjuster spring.
  7. Remove shoe adjuster.
  8. Remove upper brake shoe hold-down clip and pin.
  9. Remove lower brake shoe hold-down clip and pin.
  10. Remove upper and lower shoes with return spring from shoe actuator.
  11. Remove return spring from shoes.

    0996b43f80204c12.jpg

    Fig. View of the actuator (1), support (2), adjuster spring (3), return spring (4), caliper adapter (5), shoes (6), hold-down clips and pins (7) and adjuster (8)

To install:
  1. Install return spring between upper and lower shoes.
    NOTE Before installing shoes on actuator, make sure actuator hooked to rear cable is positioned with word -UP- facing outward.
  2. Install upper and lower shoes with return spring on shoe actuator located on parking brake cable.
  3. Install lower brake shoe hold-down pin through rear of support and lower shoe, then install hold-down clip.
  4. Install upper brake shoe hold-down pin through rear of support and upper shoe, then install hold-down clip.
  5. Install shoe adjuster. Place end of adjuster with star wheel upward.
  6. Install parking brake shoe adjuster spring.
  7. Install bolt securing parking brake cable to knuckle and tighten bolt to 21 ft. lbs. (28 Nm).
  8. Using Brake Shoe Gauge, Special Tool C-3919, or equivalent, measure inside diameter of parking brake drum portion of rotor.
  9. Place Gauge over parking brake shoes at widest point.
  10. Using adjuster star wheel, adjust parking brake shoes until linings on both park brake shoes just touch jaws on gauge. This will give a good preliminary adjustment of parking brake shoes, before a final adjustment is made at end of this procedure.
  11. Install hub and bearing with wheel speed sensor as well as all components necessary to access it.
  12. Lower vehicle.
  13. Unlock automatic adjuster in parking brake lever.
  14. Perform final adjustment of parking brake shoes

  15. Adjustment This vehicle is equipped with permanently sealed rear wheel bearings. There is no periodic lubrication or maintenance recommended for these units.


    Removal & Installation

    1. Raise and support vehicle.
    2. Remove wheel mounting nuts, then tire and wheel assembly.
    3. If equipped with AWD:
      1. Remove cotter pin, nut lock and spring washer from half shaft.
      2. While a helper applies brakes to keep hub from turning, remove hub nut and washer.
    4. Remove brake caliper and rotor from hub and bearing assembly.

      0996b43f807cb548.jpg

      Fig. Hub assembly

    5. Disconnect vehicle wiring harness connector at wheel speed sensor connector.
    6. Unclip wheel speed sensor connector from spare tire mounting support.
    7. Disconnect two sensor cable routing clips on rear suspension crossmember.
    8. Disconnect two sensor cable routing clips along toe link.
    9. Disconnect sensor cable from bracket on brake support.

      0996b43f807cb54d.jpg
    10. Completely loosen, but do not remove four bolts fastening hub and bearing in place. Once loosened from threads in hub and bearing, push bolts up against rear of hub and bearing to keep brake support plate in place when hub and bearing is removed.

      0996b43f807cb54e.jpg

      Fig. Rear hub and bearing mounting bolts

    11. Pull hub and bearing off knuckle and half shaft (if equipped with AWD), then thread wheel speed sensor cable through hole in brake support plate as it is removed with hub and bearing.
      0996b43f807cb54f.jpg
    To install:
    1. Position hub and bearing bolts though rear of knuckle and parking brake support just enough to hold support in place as hub and bearing is installed.
    2. Install hub and bearing by first feeding end of wheel speed sensor cable through hole in bottom of parking brake support. As this is being done, if equipped with AWD, slide hub and bearing onto half shaft. Place hub and bearing through brake support, onto knuckle, lining up mounting bolt holes with bolts and placing wheel speed sensor head at bottom.
    3. Install four bolts fastening hub and bearing in place. Tighten mounting bolts to 60 ft. lbs. (81 Nm).
    4. Place wheel speed sensor cable routing grommet into bracket on parking brake support.
    5. Route wheel speed sensor cable along toe link and rear suspension crossmember connecting routing clips where shown.
    1. Connect vehicle wiring harness to wheel speed sensor connector.
    2. Install brake rotor and caliper.
    3. If equipped with AWD:
      1. Install washer and hub nut on end of half shaft.
      2. While a helper applies brakes to keep hub from turning, tighten hub nut to 180 ft. lbs. (244 Nm).
      3. Install spring washer, nut lock and cotter pin on end of half shaft.
    4. Install tire and wheel assembly. Install and tighten wheel mounting nuts to 100 ft. lbs. (135 Nm).




May 18, 2011 | 2006 Chrysler Pacifica

1 Answer

I have a 2006 explorer with the rear sensing system RSS my warning does not work and there is a warning on the dash stating to check rear backup system? The fuse should be good as my heated seat and 4x4...


Have the RSS module checked for DTC'S - diagnostic trouble code's . That should always be the first step . An it is
Reverse sensing system Parking Aid The parking aid system consists of the:
  • parking aid sensors
  • parking aid speaker
  • parking aid module
The parking aid system is activated when the parking aid module receives a network messages from the instrument cluster indicating that the vehicle is in reverse. The parking aid system sounds a warning to alert the driver of stationary objects near the rear bumper when REVERSE is selected. The parking aid system assists the driver in detecting certain objects while the vehicle moves in reverse at speeds less than 4.8 km/h (3 mph). The parking aid system may not detect angular or moving objects.

  1. Visual Inspection Chart Electrical
    • Smart junction box (SJB) fuse 18 (10A)
    • Circuitry
    • Connector(s)
    • Parking aid sensors
    • Parking aid speaker
    • Parking aid module
Do you know what DTC'S are .

Parking Aid Module Diagnostic Trouble Code (DTC) Index DTC Description Source Action B1299 Power Supply Sensor Circuit Short to Ground Parking Aid Module Go To Pinpoint Test C . B1342 ECU is Faulted Parking Aid Module CLEAR the DTCs. REPEAT the parking aid module self-test. If DTC B1342 is retrieved again, INSTALL a new parking aid module. REFER to Parking Aid Module in this section. CLEAR all DTCs. REPEAT the self-test. B2477 Module Configuration Failure Parking Aid Module REFER to Section 418-01 . C1699 Left Rear Sensor Circuit Short to Battery Parking Aid Module Go To Pinpoint Test D . C1700 Left Rear Sensor Circuit Failure or Blockage Parking Aid Module Go To Pinpoint Test C . C1701 Left Rear Sensor Circuit Fault Parking Aid Module Go To Pinpoint Test E . C1702 Right Rear Sensor Circuit Short to Battery Parking Aid Module Go To Pinpoint Test D . C1703 Right Rear Sensor Circuit Failure or Blockage Parking Aid Module Go To Pinpoint Test C . C1704 Right Rear Sensor Circuit Fault Parking Aid Module Go To Pinpoint Test E . C1705 Left Rear Center Sensor Circuit Short to Battery Parking Aid Module Go To Pinpoint Test D . C1706 Left Rear Center Sensor Circuit Failure Parking Aid Module Go To Pinpoint Test D . C1707 Left Rear Center Sensor Circuit Fault Parking Aid Module Go To Pinpoint Test E . C1708 Right Rear Center Sensor Circuit Short to Battery Parking Aid Module Go To Pinpoint Test D . C1709 Right Rear Center Sensor Circuit Failure Parking Aid Module Go To Pinpoint Test C . C1710 Right Rear Center Sensor Circuit Fault Parking Aid Module Go To Pinpoint Test E . C1742 Rear Sounder Circuit Failure Parking Aid Module Go To Pinpoint Test F . C1743 Rear Sounder Circuit Short to Battery Parking Aid Module Go To Pinpoint Test F . Your best bet , take it to a qualified repair shop . Ford

Jan 02, 2018 | Ford Explorer Cars & Trucks

1 Answer

Park assist shut off intermittantly and now display reads "service park assist" permanantly. Dealer will not fix even tho' was warranty repair in Dec(less than 6 mos later problem was brought to their...


How do you know it's a sensor problem ? DTC - diagnostic trouble code ? Take's professional type scanner to read these DTC'S
DTC B0958 01: Parking Aid Rear Sensor 1 Left Corner Circuit Short to Battery
DTC B0958 06: Parking Aid Rear Sensor 1 Left Corner Circuit Short to Ground or Open
DTC B0958 08: Parking Aid Rear Sensor 1 Left Corner Circuit Signal Invalid
DTC B0958 21: Parking Aid Rear Sensor 1 Left Corner Circuit Incorrect Period
DTC B0959 01: Parking Aid Rear Sensor 1 Left Middle Circuit Short to Battery
DTC B0959 06: Parking Aid Rear Sensor 1 Left Middle Circuit Short to Ground or Open
DTC B0959 08: Parking Aid Rear Sensor 1 Left Middle Circuit Signal Invalid
DTC B0959 21: Parking Aid Rear Sensor 1 Left Middle Circuit Incorrect Period

Could have other codes
DTC B0967 02: Parking Aid Switch Circuit Short to Ground
DTC B1008 42: Calibration Data Not Programmed
DTC B1E3A 03: Sensor Power Circuit Voltage Below Threshold
DTC B1E3A 07: Sensor Power Circuit Voltage Above Threshold

There are a lot of other qualified repair shop's besides the Dealer .

Nov 05, 2017 | 2007 Chevrolet Avalanche LTZ

1 Answer

Rear parking sensors


does the version come equiped with rear park sensors????????
Does your vehicle have or could have parking aid ? Yes . Free wiring diagrams here
http://www.bbbind.com/free-tsb Enter vehicle info year , make , model an engine size . Under system click on interior & driver Amenity ,then under subsystem click on parking Aid . Click the search button then the blue link. The parking aid module is located behind right rear trim panel
Parking Aid Module CAUTION: Electronic modules are sensitive to electrical charges. If exposed to these charges, damage may result.
  1. Remove the RH interior trim. For additional information, refer to Section 501-01 .
  1. Remove the parts in the order indicated in the following illustration and table.
Inspection and Verification
  1. Verify the customer concern.
  1. Visually inspect the following for obvious signs of electrical damage.

    Visual Inspection Chart Electrical
    • Central junction box (CJB) fuse 26 (7.5A)
    • Circuitry
    • Parking aid sensors
    • Parking aid disable switch and LED
    • Parking aid speaker
    • Reversing lamps
  1. If an obvious cause for an observed or reported concern is found, correct the cause (if possible) before proceeding to the next step.
  1. If the cause is not visusally evident, connect the diagnostic tool to the data link connector and select the vehicle to be tested from the diagnostic tool menu. If the diagnostic tool does not communicate with the vehicle:
    • check that the program card is correctly installed.
    • check the connections to the vehicle.
    • check the ignition switch position.
  1. If the diagnostic tool still does not communicate with the vehicle, refer to the diagnostic tool operating manual.
  1. Carry out the diagnostic tool data link test. If the diagnostic tool responds with:
    • SCP+, SCP-, UBP or ISP circuit fault; all electronic control units no response/not equipped, refer to Section 418-00 .
    • No response/not equipped for parking aid module, Go To Pinpoint Test BC .
    • System passed, retrieve and record the continuous diagnostic trouble codes (DTCs), erase the continuous DTCs and carry out self-test diagnostics for the parking aid module.
  1. If the DTCs retrieved are related to the concern, go to the Parking Aid Module Diagnostic Trouble Code (DTC) Index.
  1. If no DTCs related to the concern are retrieved, GO to Symptom Chart to continue diagnostics

spacer-jjzrvpdgjl5rqz4khjnkbnrz-2-0.gif

Feb 18, 2018 | 2003 Ford Explorer

2 Answers

Porsche cayenne 2005 - inoperable parking sensors and mirrors


did you ever solve this problem, have the same issue myself :-(

Jun 09, 2009 | 2005 Porsche Cayenne

Not finding what you are looking for?
2007 Toyota RAV4 Logo

Related Topics:

74 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

80637 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8841 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...