Question about Cars & Trucks

Open Question

How to install clutch cable bantum 1600 cvh motor

Posted by on

Ad

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 227 Answers

SOURCE: did the ford cvh 1600 have a magneto

No, they have an alternator

Posted on Jun 17, 2013

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I set the timing on a Ford 1600 cvh bantam motor?


Hi
check timing marks on flywheel and crankshaft/pulley.
Remove no.1 plug to check it is just before tdc

Apr 10, 2016 | Ford Cars & Trucks

1 Answer

I have a ford cvh 1600 what backfire through carborator only when it is hot and then lose its power


Ford Escort carb backfire Questions & Answers - Fixya

www.fixya.com > Forum > Tags > carb backfire > Cars & Trucks > Ford
Ford Escort cars & trucks carb backfire questions and answers. ... Backfire throughcarborator and engine stopped upon returning from store. ... Turbo conversion from 1995 on a CVH engine - engine cuts out ... I have a xr3 ford escort 1600 with a weber carb,itbackfires and spits fuel up Clean the Carburator completely.

I have a xr3 ford escort 1600 with a weber carb,it backfires ...

www.fixya.com/cars/t10838117-xr3_ford_escort_1600_weber_carb
Nov 17, 2011 - I have a xr3 ford escort 1600 with a weber carb,it backfires and spits fuel up ... Turbo conversion from 1995 on a CVH engine - engine cuts out.

All comments on Ford Escort CVH Straight-through exhaust ...

https://www.youtube.com/all_comments?v=1yA5blCpTLM

Jan 05, 2016 | Ford Cars & Trucks

1 Answer

1990 ford bantam 1.6 cvh W carb adjustments fuel consumption very high and smoking a lot and when I accelerate quickly in gear or still standing it sounds like a miss and it dies


the cvh has a weber carb. these usually need a service every now and then. the smoke suggests there is a over fuelling problem and the dying of the motor sue to some flooding, i fixed a cvh this past weekend with the same problems. make sure that all the air hoses are also connected to the various ports

Feb 26, 2015 | Ford Cars & Trucks

1 Answer

How many degrees BTDC do I set my Ford 1.6 CVH motor


Most computer controlled engines have a base setting . the computer has to be uncoupled to set this , your manual will show this ,as most models differ.

Feb 22, 2015 | Ford Escort Cars & Trucks

2 Answers

Where do i get clutch master cylinder in my ford bantum


Try a used auto parts place. Try Denton Auto Salvage at 785-437-2223

Jan 03, 2014 | 2006 Ford Bantam 1.3i

1 Answer

My 92 nissan nx 1600 is very hard to shift. the shop told me its the clutch bearings. is that correct?


Very possibly. It could also be worn clutch plates, a stretched clutch cable or a loose shift lever.

Jul 24, 2013 | Cars & Trucks

1 Answer

Turbo conversion from 1995 on a CVH engine - engine cuts out


Check the auto choke to be sure its not getting stuck.

May 10, 2010 | 1983 Ford Escort Gt

1 Answer

Info on do it tyour self clutch removal on 2001 mustang 3.8


REMOVAL:
  1. Lift clutch pedal to uppermost position to disengage clutch and brake pedal pivot shaft.
  2. Push clutch and brake pedal pivot shaft forward and unhook clutch release lever cable from clutch and brake pedal pivot shaft and allow it to slowly swing rearward.
  3. Raise and support vehicle.
  4. Remove clutch release lever dust shield.
  5. Disconnect clutch release lever cable from clutch release shaft.
  6. Remove retaining clip, then clutch release lever cable from flywheel housing.
  7. Remove starter motor from flywheel housing, then engine rear plate to front lower flywheel housing bolts.
  8. Remove transmission.
  9. Remove flywheel housing back just far enough to clear clutch pressure plate, then remove housing.
  10. Remove clutch release shaft from flywheel housing by pulling it through window in flywheel housing until retainer spring disengages from pivot.
  11. Remove clutch release hub and bearing from clutch release shaft.
  12. Loosen six clutch pressure plate bolts evenly to release spring tension gradually and avoid distorting clutch pressure plate. If same clutch pressure plate is to be installed, mark plate and flywheel so pressure plate can be installed in its original position.
  13. Remove clutch pressure plate and clutch disc from flywheel.
INSTALLATION:
  1. Position clutch disc and pressure plate assembly on flywheel, noting following:
    1. Three flywheel housing to block dowels on flywheel must be properly aligned with clutch pressure plate.
    2. Bent, damaged or missing flywheel housing to block dowels must be replaced.
    3. tart clutch pressure plate bolts but do not tighten.
    4. Avoid touching clutch disc face, dropping parts or contaminating parts with oil or grease.
    5. Align clutch disc using suitable alignment tool inserted in pilot bearing.
    6. To avoid clutch pressure plate distortion, alternately tighten bolts a few turns at a time, until they are all tight, then tighten to specifications.

  2. Install transmission to flywheel housing.
  3. Install engine rear plate to flywheel front lower housing bolts, then connect clutch release cable to flywheel housing and connect retaining clip.
  4. Connect clutch release lever cable to clutch release shaft, then install clutch release lever dust shield.
  5. Install starter motor.
  6. Lower vehicle, then install clutch release lever cable as follows:
    1. Lift clutch pedal to disengage clutch and brake pedal pivot shaft.
    2. Push clutch and brake pedal pivot shaft forward and hook end of clutch release lever cable over rear of clutch and brake pedal pivot shaft.

  7. Cycle clutch pedal several times to adjust clutch release lever cable

Aug 08, 2009 | 2001 Ford Mustang

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

23 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...