Question about 2000 Ferrari Enzo

1 Answer

Pto will not engage on an auto machinic trash truck

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Ferrari Master
  • 40,701 Answers

If cable engagement check cable for failure . If air servo engagement check for broken air line to servo. Check that the pump is actually engaged but the drive pin in the gear is not broken and not driving the pump shaft.

Posted on Dec 26, 2013

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

What is the push button on the dash of a Cub Cadet 582 riding mower


I think it engages the PTO clutch for the mower deck

May 29, 2017 | Cars & Trucks

1 Answer

Where is pto over temp relay or sensor located on x495 john deere diesel engine


I worked for Kubota for 10 years and I am not familiar with a PTO temp sensor, John Deere or otherwise. The PTO function has nothing to do with engine other than slight increase in coolant temp when the PTO is under a load. Check for correct Hydraulic oil level(dipstick or sight glass in transaxel) and make sure grass or trash is not packed around the hydraulic oil cooler in front of the radiator. Remove the screen and use compressed air to clean it often. Change hydraulic oil filters every 100 hours

May 21, 2017 | Cars & Trucks

1 Answer

It's a 95 landini tractor and the tiller stops when it hits the ground


pto not properly engaged
spline stripped
sacrificial pin sheared

Jun 01, 2016 | Cars & Trucks

1 Answer

How do gears to drive pto go in the manual transmission


If your transmission is PTO ready, there will be a plate on the side of the tans where the PTO bolts to it. The PTO will have a gear that goes into the transmission that is driven off of a gear on the input shaft. You will be able to engage and disengage the PTO by a slip gear in the PTO itself.

Nov 24, 2015 | Cars & Trucks

1 Answer

3 pointg hookup wont raise or lower


ensure the gear to drive the pto pump is engaged
check oil level for the pump check controls

Jun 25, 2015 | Cars & Trucks

2 Answers

Odd experience: engine powered down going up hill, then almost stalled. PTO will not engage, now engine will not start or even turn over.


I had a similar experience and I had to replace the PTO.
What size motor do you have and what brand is it?

Apr 21, 2015 | Cars & Trucks

1 Answer

Just had a new p.t.o to a 07 mack vison it wont lift the tipper so i fitted a dummy hose the p.t.o engages and does pump but very slowly im talking like under 20litres a minute?


if you have a mack tri shaft box then check that the pto pump has been fitted to the correct hole. Some pto pumps run directly onto the counter shaft and others use an adaptor to increase the pump rpms or run from a larger gear in the box that runs the pump at higher rpms. . I suspect that the installation of the pump is incorrect and not in accordance with the fitting instructions for the pump.
Pto pumps fitted to road ranger box can be either on the side or underneath and each position connects with a different gear to drive it.

Feb 26, 2015 | Cars & Trucks

2 Answers

Case 685XL. This machine was working fine before rested in barn for the winter months. But now, fwd/reverse, H/L, 1,2,3,4 gear has some difficulties moving the machine. Have to really put the foot down...


check hydrallic fluid level in case some of it leaked out. Also check for air in lines by revving it up and trying to engage it under a load. After that, check hydrallic fluid level again.

Jan 05, 2015 | Cars & Trucks

1 Answer

2000 F550 7.3 LITER HIGH IDLE DOES NOT WORK ON COLD START OR PTO ENGAGEMENT


Have you checked the idle control sensor? Have you adjusted the idle? It may be a bad map sensor. Usually, if it is a map sensor, it will dies occasionally.

Feb 23, 2011 | 2001 Ford Super Duty F 450

1 Answer

On the fly four wheel drive goes in and out ...decides on its own when it wants to work or not - makes growly noise when going rom 2 wheel to four (regular four-not low four)


I am thinking the shifter linkage on the PTO has slipped. It is probably sitting between the two selection areas of the switch that controls the front hub engagement.

Dec 01, 2010 | 2003 Chevrolet Blazer

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

43 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ferrari Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

ROBERT GARCIA
ROBERT GARCIA

Level 3 Expert

874 Answers

yadayada
yadayada

Level 3 Expert

75005 Answers

Are you a Ferrari Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...