Question about 2007 GMC Yukon

1 Answer

How do the wiper arms come off a 2007 GMC Yukon? I just see a round button where the nut should be.

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 73 Answers

I think you will find the nut under that button,get in there and dig that button out!

Posted on May 18, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

HOW DO YOU REPLACE THE REAR WIPER MOTOR ON A 2007 chevrolet uplander


1. Remove the rear wiper arm 2. Remove the wiper driveshaft nut( nut behind wiper arm) and the washer and seal from the driveshaft 3. Remove liftgate trim pannel 4. Dissconect electrical conn and retaining screws from the motor. Reverse to install. But my advice is put the motor in but leave arm off, run the wiper motor to make sure it is working and to make sure it is at its resting spot. Then put the arm back on.

Nov 26, 2013 | 2007 Chevrolet Uplander

1 Answer

Where is the wiper motor on my 1999 GMC Yukon?


Windshield Wiper Motor
Removal & Installation
To Remove:


  1. Remove wiper arms.
  2. Remove weatherstrip from cowl.
  3. Remove two cowl vent grille panel screws.
  4. Remove windshield nozzles and hoses.
  5. Remove three cowl vent grille panels.
  6. Disconnect windshield wiper motor electrical connector.
    NOTE: Do not remove crank arm from windshield wiper motor.

  7. Loosen nuts that attach the drive link brackets to the crank arm.
  8. Remove wiper motor crank arm brackets.






    gm-06-00-1079.gif



  9. Remove three bolts and windshield wiper motor from vehicle.

To Install:


  1. Install windshield wiper motor and three bolts.

    • Torque to: 62 in lbs. (7 Nm)

  2. With right side linkage closest to the windshield wiper motor, install drive
    link brackets to wiper motor crank arm.

    • Torque nuts to: 44 in lbs. (5 Nm)

  3. Connect electrical connector.
  4. Install nozzles and windshield washer hoses to cowl vent grille.
  5. Install three cowl vent grille panels and screws to vehicle.
  6. Install weatherstrip to cowl.
  7. Install wiper arms.


prev.gif next.gif

Oct 30, 2010 | 1999 GMC Yukon

1 Answer

With the windshield wipers on a 2007 gmc yukon are you supposed to replace just the blade


most all you can buy now is the whole arm autozone or oreilys will replace these when you buy them at no charge if you are having trouble

Dec 27, 2009 | 2007 GMC Yukon

1 Answer

Need to remove the wiper arms to replace a cracked cowl on a 2005 GMC Yukon. How do they come off?


on most g.m. products they're on a spline you need to pry them upward and away from the linkage,they can be tough so hold other parts so you dont bend or break anythinf,also if you can get some penetrating oil up there it may help too, lots of dirt and corrosion in that area,good luck

Jul 10, 2009 | 2005 GMC Yukon

2 Answers

Trouble replacing wiper blades on 2004 GMC Yukon


hi from uk re wiper blade you only have to swivel blade enough to access the press clip that holds the swivel mount of the blade then while pressing clip pull wiper blade down out of the wiper arm U type hook replacement is in reverse make sure you note the old blade fits so you fit new one same way ?

Mar 27, 2009 | 2004 GMC Yukon

1 Answer

Remove wiper blade


Do you mean the wiper blade or the wiper arm?

The wiper blade should have a small tab or lever on the underside of the hinge where it attaches to the arm. Use a small screwdriver or a pick (etc..) to gently pry the lever upwards to pull the locking tab out of its corresponding hole on the wiper arm. Once the tab is up, firmly grasp the wiper blade and pull towards the base of the wiper arm. Sometimes they stick a little, just be careful not to bend the wiper arm.
If you are looking to remove the wiper arm, remove the plastic cap at the base of the wiper arm to gain access to the nut below. Using either a 13mm (1/2 inch) or 15mm socket (depending on the model) remove the nut by turning counter-clockwise. Once the nut is off, place your hand in the middle portion of the wiper arm and firmly push downward, being careful not to bend the arm. What you are trying to do is rock the arm off of the wiper motor stud. Be sure to mark where the wiper blade rests on the windshield before removing it, so you can reassemble it in the same spot when you put it back together. Use a grease pencil or something else that you can clean off later.
Hope this helps!

Mar 26, 2009 | 2006 GMC Yukon Denali

1 Answer

Windshield wiper arm


These are a tight fit...Spray a little penetrating lubricant onto it and let it sit for about 20 minutes. You will notice there are splines that match up from the drive unit to the base of the wiper arm...sometimes these can get a little corroded and becasue of the relative surface area it makes them a real pain to get off. You may need to just pry against it gently with a flat head scredriver after you spray on the lubricant. Pray at it from all different sides of the base so that it doesn't bind up and get crooked.

Hope this helps! Good Luck!

Feb 12, 2009 | 2002 GMC Yukon XL

2 Answers

Wiper Linkage question...2002 Yukon Denali XL


BINGO you need to flip the wiper arm end cover up or off and tighten the nut, 13mm usually

your wiper arm just needs to be tightened up

but align them or it as you tighten it

Jan 27, 2009 | 2002 GMC Yukon Denali

1 Answer

99 Yukon windshield wipers sometimes won t turn on and other time stop after working


We had the same problem and sometimes they wouldn't turn off. The intermittent wipers were random. We replaced the wiper motor. Be sure to get the motor with two balls on the wiper shaft (one for each wiper arm). If you can't find it, you'll have to change the part out on the new motor. Keep the wiper arms in the same location on removal, or it will jam and you'll have to start over.

Jul 14, 2008 | 1999 GMC Yukon

Not finding what you are looking for?
2007 GMC Yukon Logo

Related Topics:

121 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...