Question about 2001 Chrysler PT Cruiser

Open Question

Seat belt is locked after airbag deployment - 2001 Chrysler PT Cruiser

Posted by on

Ad

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 323 Answers

SOURCE: driver's airbag light on 2007 PT Cruiser convertable

The first code is for "driver seat track position sensor low". The module detects that the sensor input is less than or equal to 0.3 mA. The second code is referring to the first code. I have no idea what the third code is. Basically you have two different communication systems mixed. The 2001 uses the PCI bus system and the 2007 uses the CAN bus which is much faster. The first code is a CAN bus code and the second is a PCI code. As far as the airbag deploying in the event of a collision, I don't believe it will with an active code in the system. I hope this helps.

Posted on May 13, 2009

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I turn off the airbag light after accident and unlock the seat belts?


Hi Sam!

I'm Michael from Safety Restore. Our company specializes in resetting srs airbag modules and rebuilding locked and blown seat belts after accident. We use 100% OEM parts and offer Lifetime Warranty. Visit our online store to learn more.

Post Accident Restoration We reset airbag modules and repair seat belt...

$50 SRS Airbag Module Reset
$65 Seat Belt Retractor Repair
$65 Seat Belt Buckle/Pre-Tensioner Repair
$75 Seat Belt Webbing Reaplcement

Thanks!

Oct 14, 2014 | Cars & Trucks

1 Answer

07 colbalt seat belts locked


Reset the system by detaching the positive end of the battery terminal in the trunk.

Jan 20, 2013 | 2007 Chevrolet Cobalt Coupe

1 Answer

Air bag code 33 for a 2005 lincoln town car


2005 Towncar SRS Code 33 (3 flash + 3 flash, repeat this set for twice. then Beep 5 times pause x 5 = 25 beeps every 30min).

This means you have problem with left (Driver) side pretentioner (Seat belt retract system).
It doesn't mean physical belt or retract mechanism.It is just bomb wiring which is part of airbag system.
When airbag deploy, passenger must stay tight in seat otherwise body lean to front then slam back to seat by airbag.
if belt is loose or delay to lock, passenger's body rocks back and forth.So, system use small bomb (Fire power) to lock and retract seat belt when airbag deploy.There is small bomb and igniter in part of Seat belt retractor.
Code 33 is warning for this part on 2005 Towncar.(older model is different meaning in Ford/Lincoln, it's possibly passenger side airbag system for earlier model)
Before you work for any part of Airbag system and touch any "Yellow connector", * *Disconnect battery (negative side is good enough) and wait at least 5 min to clear all power in system**.(Airbag store back up power for few minutes to be able to deploy even in case if power disconnected)
by the way, you should move your driver seat most forwarded position before you disconnect battery to make it easy to work with seat belt.
locate driver side seat belt retractor (in center pillar between front and rear door, you may have to fight with weather strip)

Locate Yellow connector on bottom of Seat belt retractor (it's called "Pretensioner")it is located on very bottom of rear side of retractor.
only one yellow connector. (make sure your battery is disconnected)
Check its physical connection or looseness.if connection looks fine, you may have to replace whole seat belt ($180-$200 in Lincoln dealer)
You can check if pretensionor is good or bad by regular tester, but unless you know how, I won't tell (because I don't wan't you to blow out pretentionor).








Jul 19, 2012 | 2005 Lincoln Town Car

1 Answer

Air bag deployed and horn sets off is there a way I can stop that and reuse the horn.. I took the fuse out to stop it but I would like my horn back


Sounds like the horn switch in the steering wheel is mashed flat in the closed position. This would be part of replacing the SRS in the steering wheel.

Additionally if the airbag deployed, the pyro loads in the seat belt retractors are most likely locked in place, and also need to be replaced, to have use the seat belts again. The seat belt locked in place is not a good operational usage of them, it is not like a 5 point harness, and can cause an injury if it is locked.

Mar 30, 2011 | 2002 Ford F150 Regular Cab

1 Answer

I have a 2001 ford escape that was in a fender bender. minor visual damage but both airbags deployed. I bought new steering wheel and passanger airbag and hooked up. I was told i now need new sensors which...


this may sound crazy but this is what they say (manufactor) when ever airbags are deployed ,the following must be replaced,the deployed bags. the airbag module,crash sensors,clock spring, the belt buckles and seat belts should be inspected and checked.

Mar 08, 2010 | 2001 Ford F150 Styleside SuperCrew

1 Answer

Front seatbelt jammed


If the seat belt has jammed, you may just need to replace the mechanism- you want it to do its job correctly when you need it
For your information,--You may need to replace the mechanism for the seat belt. If the impact restraint system has encountered what they refer to as a stage one deployment due to a minor accident, the seat belt locks up, and even though the airbag(s) hasn't deployed, there are frame sensors that may need replacing reset.
We encountered this with my daughter's 05 Focus and needed to replace the belt assembly, and a couple sensors on the frame..


Dec 13, 2009 | Ford Taurus Cars & Trucks

1 Answer

The seatbelts locked up after i crashed and the airbags deployed. how do i get them to unlock?


most new cars have seat belt pretensioners that fire with air bag deployment these must be replaced.

Nov 15, 2009 | 2001 Honda Accord

1 Answer

Srs light always on in my mitsubishi eclipse


Did you change the seat belt holder. When airbags are deployed the seat belts automaticly open they still work ok but need changed

Aug 07, 2009 | 1996 Eagle Talon

1 Answer

Seat belts on both driver and pass. won't extract


Unfortunately, Yes, You will need new Seat Belts also. Once the Seat Belts and the AirBags are Deployed in a Crash, There is no Reset for the Belts. Please Rate My Response! Thanks!

Feb 01, 2009 | 1999 Toyota Tacoma PreRunner

1 Answer

Ford Focus seatbelt locked


There is a gas cylinder that tightens the belt in a minor collision, it is a one time use part it is independent of the air bag deployment system, you will have to replace the seat belt gas cylinder, that may mean a new belt assembly, not sure on focus.

Aug 22, 2008 | 2001 Ford Focus

Not finding what you are looking for?
2001 Chrysler PT Cruiser Logo

Related Topics:

33 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8514 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...