Question about Cars & Trucks

Open Question

Replace rear axle shaft in a 2009 nissan titan four wheel drive

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 78 Answers

SOURCE: four wheel won't engage

Theres a vacume dash pot under the battery box. It pulls a cable that engages the front diff. Put the vacume line and you'll have lights and four wheel drive. (it happened to my blazzer)

Posted on Dec 29, 2008

Ad
  • 1 Answer

SOURCE: 4 wheel drive not working

when you engage it in 4 wheel make sure you are getting vacuum to the acuator just pull the hose off and feel to see if there is vacuum if not check all vacuum hoses

Posted on Jan 25, 2009

  • 2 Answers

SOURCE: problems with 4 wheel drive on 04 Nissan Titan

2004 Nissan Titan when using the kick down and the accelerator pedal is about 75% depressed the RMP go into the red zone then drop to about 25K and comes close to stalling. Why?

Posted on Mar 04, 2009

F.U.B.A.R.
  • 19 Answers

SOURCE: two broken lug studs. 07 Nissan titan 4X4.

They should be replaceable w/o pulling the axle. Imagine a common nail; you have the shank of the nail with its point and the flat head on the other end. Your lug stud looks a little like that except the part that comes through the axle flange. It is a little larger than the threaded part and has "lateral lines" machined into it to grip inside the flange. Otherwise it would spin either way when you tried to tighten or remove it. To get the broken ones out, use a high quality flat end punch and a hammer to drive them backwards (toward the center of your differential) and eventually out of the flange. Look for the area that will give you the most room so they will not hit aything while they are backe out of the flange. The new studs can be installed in the reverse manner. When you get them just barely started through the flange, use your fingers to twist them back and forth to "feel" for the grooves where the old stud was seated. Once you get it barely started in the grooves, grease the threads, slip an old 1/2 inch drive socket over the new stud (make sure it doesn't fit tight) slip on a thick flat washer or 2--3 thin ones, turn your lug nut around backwards so the tapered end faces out and begin to tighten it. Go slow, make sure the new stud pulls through the flange evenly. Take the nut, washers and socket off every now and then and look at your progress. When the back side of the stud is seated on the back of the flange, you're finished. Now, always grease the studs. ALL OF THEM, EVERY WHEEL. The monkeys that put on tires these days use impact wrenches and if you just have to let them do it, grease will help you loosen the nut if you have to and it will help prevent future failures. A DRY stud and nut causes a twisting motion to take place in the body of the stud when its tightened. This leads to premature metal fatigue.

Posted on May 03, 2009

gladys_neal
  • 334 Answers

SOURCE: I have a 2001 Chevy 2500 4X4. Four wheel drive not

Sounds like the chain in the transfer case has broke or the linkage is out of adjustment

Posted on Dec 08, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

3 Answers

My front driver side axle popped out. Can i drive it?


Yes, you can replace the front axle on a Mercury Grand Marquis. All cars have two axles whether they are front wheel or rear wheel drive.------------------------------------------------------------------------------------
Tacho Pro 2008

Feb 22, 2013 | 2004 Nissan Titan

1 Answer

1998 ford explorer 2 wheel drive rear wheel bearing replacement


what about it?

conventional axle or limited slip? Get axle code off door sticker.

SECTION 205-02: Rear Drive Axle/Differential - Ford 8.8-Inch Ring Gear 1998 Explorer/Mountaineer Workshop Manual
IN-VEHICLE REPAIR Rear Wheel Bearing and Axle Shaft Oil Seal -4.0L SOHC and 4.0L EI, Conventional
Special Tool(s) swn~us~en~file=st1514a.gif~gen~ref.gif Axle Seal Replacer
T83T-1175-A swn~us~en~file=st1283a.gif~gen~ref.gif Axle Wheel Bearing Puller
T83T-1225-A swn~us~en~file=st1322a.gif~gen~ref.gif Axle Wheel Bearing Replacer
T83T-1225-B swn~us~en~file=st1326a.gif~gen~ref.gif Driver Handle
T80T-4000-W swn~us~en~file=st1185a.gif~gen~ref.gif Impact Slide Hammer
T50T-100-A
Removal
  1. Remove the axle shaft; refer to Axle Shaft in this section.
Axle Shaft Removal
  1. swn~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not use heat to loosen a seized lug nut. Heat can damage the wheel (1007) and the rear wheel bearings (1225).
    Loosen the lug nuts (1012).
    1. Remove the center cap.
    1. With the weight of the vehicle on the wheels, loosen the lug nuts.
  1. Raise and support the vehicle.
  1. Remove the wheel and tire assembly.
    1. Remove the lug nuts.
    1. Remove the wheel and tire assembly.
  1. Remove the axle housing cover (4033).
    1. Loosen the axle housing cover bolts (4346) and drain the rear axle (4001).
    1. Remove the axle housing cover bolts.
    1. Remove the axle housing cover.
  1. Remove the rear disc brake rotors (2C026); refer to Section 206-04 .
  1. swn~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Once the differential pinion shaft (4211) has been removed, turning the differential case (4204) or an axle shaft (4234) will cause the differential pinion gears (4215) to fall out of the assembly. This could result in chipped or damaged components.
    Remove the differential pinion shaft.
    1. Remove the differential pinion shaft lock bolt.
    1. Remove the differential pinion shaft.
  1. swn~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not damage the rubber O-rings in the U-washer grooves.
    Remove the U-washers (4N237).
    1. Push the axle shafts inboard.
    1. Remove the U-washers.
  1. Reinstall the differential pinion shaft.
    1. Install the differential pinion shaft.
    1. Install the differential pinion shaft lock bolt finger-tight.
  1. swn~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not damage the inner wheel bearing oil seal (1177).
    Remove the two axle shafts.
Installation
  1. Lubricate the lip of the inner wheel bearing oil seal.
    • Use Premium Long-Life Grease XG-1-C or equivalent meeting Ford specification ESA-M1C75-B.
  1. swn~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Once the differential pinion shaft has been removed, turning the differential case or an axle shaft will cause the differential pinion gears to fall out of the assembly. This could result in chipped or damaged components.
    Remove the differential pinion shaft.
    1. Remove the differential pinion shaft lock bolt.
    1. Remove the differential pinion shaft.
  1. swn~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not damage the inner wheel bearing oil seal.
    Install the two axle shafts.
  1. swn~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not damage the rubber O-rings in the U-washer grooves.
    Install the U-washers.
    1. Position the two U-washers on the button end of the axle shafts.
    1. Pull the axle shafts outward.
  1. Install the differential pinion shaft.
    1. Align the hole in the differential pinion shaft with the differential pinion shaft lock bolt hole.
    1. Install the differential pinion shaft lock bolt.
  1. Install the rear disc brake rotors; refer to Section 206-04 .
  1. Install the axle housing cover and fill the rear axle housing (4010) with 2.4 liters (5.5 pints) of specified lubricant; refer to Axle Housing Cover in this section.
  1. swn~us~en~file=ani_caut.gif~gen~ref.gif WARNING: Always remove any corrosion, dirt or foreign material that may be present on the mounting surfaces of the wheel or the surface of the wheel hub or rear disc brake rotor that contacts the wheel. Installing wheels without proper metal-to-metal contact at the wheel mounting surfaces can cause the lug nut to loosen and the wheel to come off while the vehicle is in motion, causing loss of control.
    Clean the wheel hub and mounting surfaces.
  1. Install the tire and wheel assembly.
    1. Position the tire and wheel assembly.
    1. Install the lug nuts and lower the vehicle.
    1. Tighten the lug nuts.
    1. Install the center cap.


  1. swn~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Never remove the axle shaft oil seal by itself. Always remove the rear wheel bearing and the axle shaft oil seal at the same time.
    NOTE: If the axle shaft oil seal is leaking, the axle housing vent may be plugged with debris.
    Use Impact Slide Hammer and Axle Wheel Bearing Puller to remove the rear wheel bearing and the axle shaft oil seal.
Installation
  1. Lubricate the new rear wheel bearing.
    1. Use Thermally Stable Rear Axle Lubricant XY-80W90-QL or equivalent meeting Ford specification WSP-M2C197-A.
  1. Use Axle Wheel Bearing Replacer with Driver Handle to install the rear wheel bearing.
  1. Lubricate the lip of the new axle shaft oil seal.
    • Use Premium Long-Life Grease XG-1-C or equivalent meeting Ford specification ESA-M1C75-B.
  1. Use Axle Seal Replacer with Driver Handle to install the axle shaft oil seal.
  1. Install the axle shaft; refer to Axle Shaft in this section.

May 18, 2011 | Ford Explorer Cars & Trucks

1 Answer

I have a nissan xtrail 2004 model and have just had a front right wheel bearing replaced, now i'm told by the mechanic he wasn't able to remove the bearing so instead he had to replace the drive shaft, is...


It doesn't seem like it should have been all that bad with a 2004.Please tell me a couple things though.Are you in an extreme weather environment?Fairly hot summer,fairly cold winter,cars rusty within 5 years?Did he call it a drive shaft?If it is front wheel drive,it is more likely a CV axle,however,I am not familiar with the setup of 4 wheel drive vehicles.There may be different interpretations between the 2 countries but to me,a drive shaft connects the transmission to the rear axle.The axle is what the rear tires of a front wheel drive are held together by.A CV axle is what goes from the transmission to each of the front two tires,each tire having one CV axle and joint.I would get a second opinion.Good luck mate!

Aug 05, 2010 | Nissan Xterra Cars & Trucks

2 Answers

I would like to know if the wheel bearing is in the shaft or the hub?


The Constant Velocity (CV) joints are located on the inner and outer edges of the axle shaft. The axle shaft runs through the hub and bearing in the spindle.

Jun 16, 2010 | 1999 Daewoo Nubira

1 Answer

My brake, slip and VDC indicators stay on.


Check brake fluid level, add fluid from sealed container if needed.

Also check for leaking rear axle seals. Look for oil on the inside of rear wheels.

May 06, 2010 | 2004 Nissan Titan

1 Answer

I am going to change my rear diff. in my 2005 nissian titan with a tru trac. do i have to take off my rear tires and and pull out my axle shafts


If you're changing the complete differential housing.
No. You can leave them on if you like. Hope this helps.

Mar 31, 2010 | 2005 Nissan Titan

1 Answer

95 nissan 4x4 truck. four wheel drive light comes but does'nt en


the front axles have pinon gear box that the shaft from the transfer case goes to, it has a vacuum hose to it or a solenoid actuator check these for proper function this is how the power is turned on to the wheels.

Feb 13, 2010 | 1990 Nissan Hardbody King Cab

1 Answer

Truck will not go into four wheel drive when the slip or abs light is on


This is designed that way so that you don't damage the transfer case. All four tires need to be going the same speed in order to shift into 4 wheel drive. If you're spinning a tire then one axle is going faster than the other and it would destroy your t-case if it did try to shift. Same for when you're braking. You want to be off the throttle when you shift into 4 wheel drive. Idealy you want to be stopped, it's much easier on the transfer case if you are.

Nov 09, 2009 | 2006 Nissan Titan

2 Answers

Need to get axles off a 2005 Nissan Titan


Two choices. Find an axle assy from a wrecked truck, or if your ring/pinion gears are OK, install Detroit Locker TrueTrac to replace spider gears. Good luck.

Mar 18, 2009 | 2005 Nissan Titan

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

34 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76070 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...