Question about 1998 Ford Crown Victoria

1 Answer

I am trying to replace the fuel pump on my 1998 Crown Victoria and cannot remove the fuel lines to drop the gas tank to get to the pump...is there any tricks? They are stuck on there and I have the tool they suggest you use to remove them! What do I do?

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 105 Answers

These fittings tend to cake up with dirt and rust try to flush out the connectors with a good penatrating oil like pb blaster o wd40 and try to twist tool in connector while trying to remove them usally takes some work but will get them to release aslo you may have to push in as though you are installing the connectors to get locks to fully release

Posted on May 18, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

My 1992 crown vic is not getting any gas to the injectors i think its my fuel pump i dont know how to take the pump off wat can i do and how do i take the pump off


fuel pump is in the gas tank. Have to drop the gas tank. Make sure that u run all tghe gas out before u drop the tank. Also make sure that u mark how the old pump comes out and put back the same way so the float will work. Watch for the wires on the pump that u do not break any of them.

Mar 25, 2011 | 1992 Ford Crown Victoria

1 Answer

How to access 1995 crown victoria fuel pump


The fuel pump is attached to the fuel tank on these models. It will be necessary to drop the fuel tank to gain access to it.
  1. Disconnect the battery
  2. Remove the the fuel tank flange and bolts supporting the tank
  3. Carefully lower the tank (this is much easier if the tank is empty as the tank can be very heavy)
  4. Remove all the fuel lines and connectors
You now have access to the fuel pump.
If you want to be unconventional about it you could access it by cutting through your trunk to get at it. Just be careful not to puncture any vital parts.

Feb 17, 2011 | 1995 Ford Crown Victoria

1 Answer

My problem is in the fuel pump for ford crown victoria model 2004\r\npleas tell me all the solution and causes


You haven't told us anything
Drivability issues,stalling,no starts?
The fuel pump is in the gas tank,
it has to come down to replace pump
if that is necessary

A pump can bind mechanically
The armature can wear out
The volumn and pressure can drop

Jan 31, 2011 | 2004 Ford Crown Victoria

2 Answers

Need to replace fuel pump, does gas tank have to be removed, or is there a access plate?


No access panel, the fuel tank will have to be remove, to install fuel pump.

Sep 01, 2010 | 1994 Ford Crown Victoria

1 Answer

How to change a fuel pump on 1998 ford crown


you have to remove the fuel tank- it is located inside the tank

Feb 16, 2010 | 1998 Ford Crown Victoria

2 Answers

How to drop fuel tank


purge the pressure at the fuel rail on the engine to relieve the pressure.remove the two bolts near the rear axle at the gas tank straps,lower slowly and unplug the lines and sender wires.that simple.

Oct 31, 2009 | 1999 Ford Crown Victoria

1 Answer

Do you need to remove gas tank to change fuel pump on 99 crown vic the pump is on the front side of the tank and is held in with like 6 bolts also where is the wiring connector


YOU SHOULDNT HAVE TO DROP THE TANK REMOVE 6 BOLTS ON TOP OF FUEL PUMP MODULE.YOUR WIRING CONNECTOR IS ALSO ON TOP OF THE PUMP MODULE.

Sep 22, 2009 | 1999 Ford Crown Victoria

1 Answer

99 Crown Victoria fuel pump replacement


Use lots of wd40 on tank strap bolts. If they bigin to bind tighten them up and losen again to get rust out of threads. If you remove the straps, why not remove the fill neck and lower tank? Much easier to work that way!!!

Mar 28, 2009 | 1999 Ford Crown Victoria

1 Answer

94 CROWN VICTORIA FUEL PUMP


Yes you can replace it. It is in the fuel tank. You will need to drain the tank and remove it to gain access to the fuel pump. A floor jack will help when lowering the fuel tank. If you fo to a dealer to do this you will be looking probably around $700.00 to replace the pump.

Feb 17, 2009 | 1994 Ford Crown Victoria

Not finding what you are looking for?
1998 Ford Crown Victoria Logo

163 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75744 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

fordexpert

Level 3 Expert

5495 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...