Question about 2003 Mazda Mazda6

1 Answer

Low beam on 79 el camino

My high beam is stuck how can i get it back to low beam?

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 20 Answers

Your switch (prob on the floor, to the left) may be depressed or need to be replaced.

Posted on Oct 17, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Heater won't work on high


I just had a question like this the other day, also on an El Camino.
We talked about the high blower relay being the possible cause.

Sep 20, 2012 | 1982 Chevrolet El Camino

1 Answer

2000 Chevrolet S-10 low beam lights won't come on. High beam works.


sounds like the high beam switch is bad, it controls the power for low and high beams

Sep 22, 2011 | 1982 Chevrolet El Camino

1 Answer

2001 Ford Focus - High beam / low beam problem with headlights


just replace the dimmer switch under the column its wore out on the low beam side

Jan 17, 2010 | 2005 Ford Focus

1 Answer

I removed the tilt steering colum housing to instal a new cruise


The plastic piece goes between the steel rod and cruise/wiper lever. You will have to remove the wheel and the upper bearing housing to get it back where it goes. If you put some wheel bearing grease on it then it will stay in place during reassembly.. Good Luck

May 15, 2009 | 1986 Chevrolet El Camino

1 Answer

My 1981 chevy El Camino V6 3.8L 229 idle gets high when engine is hot and when engine gets cold idle drops not sure why can i have any suggestions


Sounds like a problem with your choke. It may just need to be cleaned (linkages and all). If the choke doesn't close after reaching operating temperature, the engine will rev high. This indicates a choke stuck in the open position. Also, you may need to look for a vacuum leak if cleaning it doesn't fix it. On a 1981 GM product, I'd expect the vacuum hoses to be stiff and cracking.

May 02, 2009 | 1982 Chevrolet El Camino

1 Answer

Diagram for high beem switch on a 1981 El Camino


my car is choking and dieing coming to a stop its a 81 elco wit 89 tuneport motor vinf i changed the throttle pisition sensor /egr valve/sender/the owner said he change the fulepump. i notice a few times not all the time wen u rev the motor and let off the gas the idle drops then sets itself? and wen u put it in drive to take off if u hit the gas it hessitate a little? i need some help!!! marvin

Jan 14, 2009 | 1982 Chevrolet El Camino

1 Answer

Headlight switch 1982 el camino


I had the same problem. the switch broke. So i took apart the whole steering wheel until i looked under the dash near the pedals. if you look under the dash then you will find that there is a small white square looking thing with rod connected to it. thats the one you want to change. hope this helps

Dec 28, 2008 | 1982 Chevrolet El Camino

1 Answer

Hi low hiead light switch 82 el camino wher does the rod hook up


should be a switch mounted to the top lower steering column that the rod fits into that operates the high/low beams

Dec 28, 2008 | 1982 Chevrolet El Camino

1 Answer

New carburetor installed on 79 el camino


I am familiar with these, a manual choke carb works off of a bimetal coil in the manifold exhaust crossover on the passenger side of the intake, Make sure it is hooked up, then while the car is cold, on the rockchester carbs, use an 1/8 in drillbit to set choke. You have to loosen the three screws on the choke to set, when the choke flap, the very top one on the carb touches the drillbit, set it there and lock down screws, pump once or twice and it should start and idle, as the bimetal coil heats up it should open the top flap. if you try to accelerate before it is wam it will disconnect from the auto choke. I hope this helps if not please do not rate me at all, if it does help you fix your problem then please give me a fixya,

Dec 22, 2008 | 1987 Chevrolet El Camino

Not finding what you are looking for?
2003 Mazda Mazda6 Logo

Related Topics:

117 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

76848 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8582 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...