Question about 1999 Toyota RAV4

Open Question

I need torque settings on a cylinder head for Toyota rav 4 2.0

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
joecoolvette
  • 5660 Answers

SOURCE: need the cylinder head torque settings on a toyota

Tighten in several passes to 44 foot pounds.

I just wanted to add. Since this is an aluminum cylinder head, I hope you loosened the head in the loosening torque pattern. The pattern opposite of the torque tightening pattern. If not, you stand the chance of warping the head.

Again, since it's an aluminum head, it needs to be checked for flatness. Most aluminum heads need to be surfaced before re-installing.

Tightening torque pattern is as follows:

1.The Drivers side of the engine is the Left side.
From the Front going towards the back; the bolts are numbered 10, 6, 1, 3, and 7.
From the Front going towards the back on the Passenger side; the bolts are numbered 8, 4, 2, 5, and 9.

The Exhaust and Intake Camshaft Bearing Cap bolts go to 9 foot pounds. Tighten gradually. One bolt to the other with so many foot pounds, work back, and forth up to 9lbs.

Camshaft Timing Pulley bolts go to 43 foot pounds. (In a tightening sequence, and gradually)

Posted on Jul 25, 2009

Ad
  • 1779 Answers

SOURCE: need torque settings for 1985 4A corolla cylinder head

hey, torque must be done in 3 steps:
1st 22 ft lbs
2nd 43 ft lbs
final 47 ft lbs
use this sequence of tightening:

9 - 3 -1 -6 -8
7 - 5 - 2 -4 - 10

Posted on Jan 14, 2009

  • 7 Answers

SOURCE: Looking for the cylinder head torque settings for



  1. tighten all the bolts down to about 46 lbs ppt in the right order specified by manufactorer
  2. then about another 1/2 -5/8 of a turn for the final tightening


Thats about standard throughout engine rebuilding

Posted on May 05, 2009

  • 115 Answers

SOURCE: cylinder head torque settings for a toyota 1493cc

If you have a vehicle application for the motor you can get a Haynes or Chilton manual from your local auto parts store. They usual run around $30.

Posted on Sep 04, 2009

Pelukes01
  • 52 Answers

SOURCE: what are the cylinder head torque settings for a

0900c1528006efe6.jpgUmiformilly tighten each of the ten head bolts in several passes, in the sequence shown. Tighten them to 44 ft. lbs. (60 Nm).

Posted on Jul 23, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I need to know torque specs for rav 4 1az engine


Cylinder Head
stg 1 = 40NM
stg 2 = 79NM
stg 3 = 90^
Main bearing
stg 1 = 20NM
stg 2 = 40NM
stg 3 = 90^
Big end bearing 25NM then 90^

Sep 22, 2014 | Toyota RAV4 Cars & Trucks

1 Answer

Toyota 2c. I need cylinder head and flywheel Torque settings


Toyota 2c ...
USE NEW BOLTS...
Torque sequence:
You're driving a diesel single cylinder head engine. Engine head torque has to be done in specific order and stages if not can warp head or break bolts. Suggest you get torque sequence and torque specs from your Toyota dealer, they can give you correct answer. Don't trust answers on here, if you choose wrong specs. could end up messing up head.


Flywheel - Use a Sealer on bolt, Manual Transmission 88nm/65 ft lb... Auto Transmission 74nm/55 ft lb

Aug 06, 2014 | Cars & Trucks

1 Answer

Hi I need the torque settings for both the cylinder head and the bottom end bearings for a 1997 Toyota Prado (3.4litre petrol). Thanks


1997 Toyota Prado 5VZ-FE
Cylinder head bolts:

Tighten the cylinder head bolts in criss cross manner inside out, in four stages as under:
Stage 1. Torque the bolts up to 17 Nm.
Stage 2. 34 Nm.
Stage 3. Rotate all the bolts 90 degrees.
Stage 4. Finally rotate all the bolts further 90 degrees.

Main Bearings:
Tighten the main bearing bolts in two stages, as under:
Stage 1. 61 Nm.
Stage 2. Rotate the bolts further 90 degrees.

Big end bearings:
Tighten the big end bolt of connecting rods in two stages as under:
Stage 1. 25 Nm.
Stage 2. Rotate the bolts further 90 degrees.

Feb 27, 2014 | Toyota Land Cruiser Cars & Trucks

1 Answer

I need torque settings for engine 15B/F 4104cc


Check out the help links mentioned below:----
Cylinder Head Torque Setting http://schematicsdiagram.blogspot.com/2012/10/cylinder-head-torque-setting.html
----------- Lexus LS400: Transmission or Torque Converter? http://technoanswers.blogspot.in/2012/04/lexus-ls400-transmission-or-torque.html

----------
For more help.keep updated.
Thanks.

Oct 15, 2012 | Toyota Cars & Trucks

1 Answer

1999 toyota rav 4 engine oil cooler bolt torque setting


INSTALL OIL COOLER
-clean the oil cooler contact surface on the oil cooled mounting
-install a new O-ring to the oil cooler.
-temporarily install the oil cooler with the nut
-apply a light coat of engine oi on the threads and under the head of the relief vale
-install the plate washer and union bolt. torque 78Nm (800kgfcm, 58 ft lbs.)
-tighten the nut,torque 8.8Nm (90kgfcm, 78 inch lbs.)
-connect the 2 water bypass hoses to the oil cooler.

HOPE THIS CAN HELP.

Apr 26, 2010 | 1999 Toyota RAV4

1 Answer

Head bolt tourqe settings on a toyota cressida


Cylinder head bolt removal sequence


Removal sequence: Front 3 7 11 13 10 6 2 1 5 9 14 12 8 4

***CAUTION*** The above sequence must be followed during removal as to avoid warpage of the cylinder head unit

Reverse sequence to install, Step 1: Torque to 10 Ft/Lbs Step 2: Torque to 18 Ft/Lbs Step 3: Torque to 25 Ft/Lbs Step 4: Turn an additional 90 degrees Step 5: Turn an additional 90 degrees Step 6: Torque the 2 recessed 8mm bolts to 13 Ft/Lbs *** CAUTION *** engine uses Torque To Yield head bolts (TTY) that permanently stretch during the initial installation. New head bolts must be used when cylinder head is replaced or re-installed to obtain proper Torque

Don't forget to rate this answer, Good Luck

Apr 24, 2010 | 1992 Toyota Cressida

1 Answer

Toyota windom v6 head bolts torque settings


INSTALL CYLINDER HEAD if any bolts broken or deformed , replace it.

7------2-----4--------6
5------3-----1--------8
FRONT sequence head bolts
8-------1-----3-------5
6-------4-----2-------7

CYLINDER HEAD bolts are tightened in three progressive steps
1. 34 Nm ( 25 ft.lb)
2. 90 degree
3. another 90 degree.

double check everythings before install the head,
be sure to install the GASKET correctly.

Hope this can help.

Apr 19, 2010 | 1993 Toyota Camry V6

2 Answers

Torque setting cylinder head bolt 4 cylinder KIA sportage


I need the torque settings and pattern for a Kia Sportage 2.2

Nov 24, 2009 | 2001 Kia Sportage

1 Answer

Need torque settings for 1985 4A corolla cylinder head


hey, torque must be done in 3 steps:
1st 22 ft lbs
2nd 43 ft lbs
final 47 ft lbs
use this sequence of tightening:

9 - 3 -1 -6 -8
7 - 5 - 2 -4 - 10

Jan 14, 2009 | 1985 Toyota Corolla 2 Door

Not finding what you are looking for?
1999 Toyota RAV4 Logo

Related Topics:

379 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

77169 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22258 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8725 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...