Question about 2007 Toyota Tacoma

1 Answer

Air pump with switching valve

Is the air pump with the switching valve assembly the only air pump that i have on this pick-up ?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Toyota Master
  • 20,706 Answers

Are you talking, 4wd axle locks , or A/T internals. or ?
is there a symptom or curious.?
the FSM covers it all, buy one.
or of the lighter version, use alldata.com
what system?

Posted on Dec 26, 2013

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My 2008 Trailblazer has OBD-II code P2430. How do I replace the secondary air injection pump?


This code doesn't mean to replace the air pump ,
DTC P2430 : Secondary Air Injection (AIR) System Pressure Sensor Circuit
Circuit/System Description
The secondary air injection (AIR) system aids in the reduction of hydrocarbon emissions during a cold start. The system forces fresh filtered air into the exhaust stream in order to accelerate the catalyst operation. An electric air pump, the secondary AIR injection pump, provides filtered air on demand to the AIR control solenoid valve/pressure sensor assembly. The AIR control solenoid valve/pressure sensor assembly controls the flow of air from the AIR pump to the exhaust manifold. The AIR solenoid relay supplies the current needed to operate the AIR control solenoid valve/pressure sensor assembly. A pressure sensor is used to monitor the air flow from the AIR pump. The engine control module (ECM) supplies the internal pressure sensor with a 5-volt reference, an electrical ground, and a signal circuit.
This is a pressure sensor problem . What this video on testing !
Chevrolet Malibu P2432 Secondary Air Injection System

May 11, 2017 | Cars & Trucks

1 Answer

P0412 valve a problem where is valve a located on a 2002 buick rendezvous


This is the electrically driven secondary air injection air pump. Please read all the information at the link before you buy or replace any parts. In most cases the entire air injection pump assembly must be replaced.
P0412 Secondary Air Injection System Switching Valve Circuit Malfunction

Jul 06, 2016 | 2002 Buick Rendezvous

1 Answer

Find the sensor code P2430


DTC P2430 : Secondary Air Injection (AIR) System Pressure Sensor Circuit
Circuit/System Description
The secondary air injection (AIR) system aids in the reduction of hydrocarbon emissions during a cold start. The system forces fresh filtered air into the exhaust stream in order to accelerate the catalyst operation. An electric air pump, the secondary AIR injection pump, provides filtered air on demand to the AIR control solenoid valve/pressure sensor assembly. The AIR control solenoid valve/pressure sensor assembly controls the flow of air from the AIR pump to the exhaust manifold. The AIR solenoid relay supplies the current needed to operate the AIR control solenoid valve/pressure sensor assembly. A pressure sensor is used to monitor the air flow from the AIR pump. The engine control module (ECM) supplies the internal pressure sensor with a 5-volt reference, an electrical ground, and a signal circuit.

Sep 14, 2015 | 2008 Chevrolet Chevrolet Cobalt LT

1 Answer

Signs a fuel pump is failing


Ford fuel pymps are notorious for the check valve in the fuel pump assembly to fail. The check valve keeps the fuel lines and fuel rail full of pressurized fuel. Borrow a fuel,pressure gauge. The pressure should stay up when you shut the,engine down. If it drops to 0 right away, replace the pump module

Sep 02, 2014 | 2004 Ford Ranger

1 Answer

2002 isuzu rodeo cylinder head torque lbs. for 2.2


Print


Removal & Installation

2.2L Engine

  1. Before servicing the vehicle, refer to the Precautions section.
  2. Drain the cooling system.
  3. Relieve the fuel system pressure.
  4. Remove or disconnect the following: Negative battery cableIntake Air Temperature (IAT) sensor connectorPositive Crankcase Ventilation (PCV) valve and hoseAir intake assemblyUpper radiator hoseAccessory drive beltExhaust front pipeAlternator and bracketsCrankshaft Position (CKP) sensor connectorKnock sensor connectorHeater hosesWater bypass hoseFuel linesEvaporative Emissions (EVAP) valve connectorCanister hoseIntake manifoldEngine wiring harness connectors at left rear of the engine compartmentPower steering pump pressure switch connectorFront coverSpark plugs and wiresCamshaft Position (CMP) sensorValve coverTiming belt. Refer to the Timing Belt unit repair section.Timing belt idler pulleysTiming belt rear coverOil pressure switch connectorCamshaftsCylinder head. Remove the bolts in reverse of the tightening sequence.

    Negative battery cable Intake Air Temperature (IAT) sensor connector Positive Crankcase Ventilation (PCV) valve and hose Air intake assembly Upper radiator hose Accessory drive belt Exhaust front pipe Alternator and brackets Crankshaft Position (CKP) sensor connector Knock sensor connector Heater hoses Water bypass hose Fuel lines Evaporative Emissions (EVAP) valve connector Canister hose Intake manifold Engine wiring harness connectors at left rear of the engine compartment Power steering pump pressure switch connector Front cover Spark plugs and wires Camshaft Position (CMP) sensor Valve cover Timing belt. Refer to the Timing Belt unit repair section. Timing belt idler pulleys Timing belt rear cover Oil pressure switch connector Camshafts Cylinder head. Remove the bolts in reverse of the tightening sequence.

To install:


0996b43f802097a8.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Cylinder head torque sequence-2.2L (VIN D) engine

NOTE Use new cylinder head bolts for assembly.

  1. Install the cylinder head with a new gasket. Tighten the bolts in sequence as follows: Step 1: 18 ft. lbs. (25 Nm)Step 2: Plus 90 degreesStep 3: Plus 90 degreesStep 4: Plus 90 degrees
    1. Step 1: 18 ft. lbs. (25 Nm)
    2. Step 2: Plus 90 degrees
    3. Step 3: Plus 90 degrees
    4. Step 4: Plus 90 degrees

  2. Install or connect the following: CamshaftsOil pressure switch connectorTiming belt rear coverTiming belt idler pulleys. Tighten the bolts to 18 ft. lbs. (25 Nm).Timing beltValve coverCMP sensorSpark plugs and wiresFront coverPower steering pump pressure switch connectorEngine wiring harness connectors at left rear of the engine compartmentIntake manifoldCanister hoseEVAP valve connectorFuel linesWater bypass hoseHeater hosesKnock sensor connectorCKP sensor connectorAlternator and bracketsExhaust front pipeAccessory drive beltUpper radiator hoseAir intake assemblyPCV valve and hoseIAT sensor connectorNegative battery cable

    Camshafts Oil pressure switch connector Timing belt rear cover Timing belt idler pulleys. Tighten the bolts to 18 ft. lbs. (25 Nm). Timing belt Valve cover CMP sensor Spark plugs and wires Front cover Power steering pump pressure switch connector Engine wiring harness connectors at left rear of the engine compartment Intake manifold Canister hose EVAP valve connector Fuel lines Water bypass hose Heater hoses Knock sensor connector CKP sensor connector Alternator and brackets Exhaust front pipe Accessory drive belt Upper radiator hose Air intake assembly PCV valve and hose IAT sensor connector Negative battery cable
  3. Fill the cooling system.
  4. Start the engine and check for leaks.

  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Drain the cooling system.
  3. Relieve the fuel system pressure.
  4. Remove or disconnect the following:

    Negative battery cable Intake Air Temperature (IAT) sensor connector Positive Crankcase Ventilation (PCV) valve and hose Air intake assembly Upper radiator hose Accessory drive belt Exhaust front pipe Alternator and brackets Crankshaft Position (CKP) sensor connector Knock sensor connector Heater hoses Water bypass hose Fuel lines Evaporative Emissions (EVAP) valve connector Canister hose Intake manifold Engine wiring harness connectors at left rear of the engine compartment Power steering pump pressure switch connector Front cover Spark plugs and wires Camshaft Position (CMP) sensor Valve cover Timing belt. Refer to the Timing Belt procedure. Timing belt idler pulleys Timing belt rear cover Oil pressure switch connector Camshafts Cylinder head. Remove the bolts in reverse of the tightening sequence.

To install:

0996b43f802097a8.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Cylinder head torque sequence-2.2L (VIN D) engine


NOTE Use new cylinder head bolts for assembly.

  1. Install the cylinder head with a new gasket. Tighten the bolts in sequence as follows:
    1. Step 1: 18 ft. lbs. (25 Nm)
    2. Step 2: Plus 90 degrees
    3. Step 3: Plus 90 degrees
    4. Step 4: Plus 90 degrees

  2. Install or connect the following:

    Camshafts Oil pressure switch connector Timing belt rear cover Timing belt idler pulleys. Tighten the bolts to 18 ft. lbs. (25 Nm). Timing belt Valve cover CMP sensor Spark plugs and wires Front cover Power steering pump pressure switch connector Engine wiring harness connectors at left rear of the engine compartment Intake manifold Canister hose EVAP valve connector Fuel lines Water bypass hose Heater hoses Knock sensor connector CKP sensor connector Alternator and brackets Exhaust front pipe Accessory drive belt Upper radiator hose Air intake assembly PCV valve and hose IAT sensor connector Negative battery cable
  3. Fill the cooling system.
  4. Start the engine and check for leaks.

May 26, 2012 | Isuzu Rodeo Cars & Trucks

1 Answer

Code p1494. what do i look for.


P1494 (M)Leak Detection Pump Sw or Mechanical Fault. Incorrect input state detected for the Leak Detection Pump (LDP) pressure switch.

The Evaporative LDP switch may be bad or the pump itself has a problem. Check the pump, the wire connections, and the hoses attached to it.





LEAK DETECTION PUMP (LDP)
OPERATION
The Leak Detection Pump (LDP) is used only with
certain emission packages.
The LDP is a device used to detect a leak in the
evaporative system.
The pump contains a 3 port solenoid, a pump that
contains a switch, a spring loaded canister vent valve
seal, 2 check valves and a spring/diaphragm.
Immediately after a cold start, engine temperature
between 40°F and 86°F, the 3 port solenoid is briefly
energized. This initializes the pump by drawing air
into the pump cavity and also closes the vent seal.
During non-test test conditions, the vent seal is held
open by the pump diaphragm assembly which pushes
it open at the full travel position. The vent seal will
remain closed while the pump is cycling. This is due
to the operation of the 3 port solenoid which prevents
the diaphragm assembly from reaching full travel.
After the brief initialization period, the solenoid is
de-energized, allowing atmospheric pressure to enter
the pump cavity. This permits the spring to drive the
diaphragm which forces air out of the pump cavity
and into the vent system. When the solenoid is energized
and de-energized, the cycle is repeated creating
flow in typical diaphragm pump fashion. 180562d1295135687t-diagnostic-code-p1494-evap-wldp.jpg

Jan 19, 2011 | 1997 Jeep Grand Cherokee

1 Answer

Hi I have a 98 gmc sierra 1500 with 5.7 vortec, recently replaced gas tank and fuel pump engine light came on had obd code po442 change gas line to evap canister to high pressure fuel line light went off,...


It's hard to find these small leaks. If you have a vacuum pump, there are a few tests you can run on the components of the system. See below.


TESTING

Vapor Canister
See Figure 1

  1. Apply a length of hose to the lower tube of the purge valve assembly and attempt to blow air through it. There should be little or no air should passing into the canister.

If the canister is equipped with a constant purge hole, a small amount of air will pass into the canister.
  1. Using a hand-held vacuum pump, apply a vacuum of 15 in. Hg (51 kPa) to the control vacuum (upper) tube. If the vacuum does not hold for at least 20 seconds, the diaphragm is leaking. Replace the canister.
  2. If the diaphragm holds vacuum, attempt to blow air through the hose connected to the PCV tube while vacuum is still being applied. An increase of air should be observed. If no increase is noted, the canister must be replaced.
jturcotte_228.gif

Fig. Fig. 1: Cross-section of the vapor canister


Fuel Tank Pressure Control Valve

  1. Attach a length of hose to the tank side of the valve assembly and try to blow air through it. Little or no air should pass into the canister.
  2. Using a hand-held vacuum pump, apply vacuum equivalent to 15 in. Hg (51 kPa) to the control vacuum tube. If the diaphragm does not hold vacuum, the diaphragm is leaking. Replace the valve.
  3. If the diaphragm holds vacuum, attempt to blow air through the hose connected to the valve while vacuum is still being applied. Air should pass. If no air is noted, the valve must be replaced.

Thermostatic Vacuum Switch
  1. With engine temperature below 100°F (38°C), apply vacuum to the manifold side of the switch. The switch should hold vacuum.
  2. Start and continue to run the engine until the engine temperature increases above 122°F (50°C). The vacuum should drop off.
  3. Replace the switch if it fails either test.

purge valve location:

jturcotte_229.gif


EVAP vacuum switch pic:

jturcotte_230.gif

EVAP system diagram:
jturcotte_231.gif

Nov 20, 2010 | GMC Sierra 1500 Cars & Trucks

2 Answers

When I turn my air conditioner on, the air blows out on the dashboard for the windshield and not from the vents. What can I do??


The blend door actuated by solenoids may not be working correctly causing a/c cool air to come out of the windshield vents, rather than the regular front vents.

Defroster Valve Actuator 1996 – 1999 1996 – 1999 HVAC Actuators gm-10-00-1840.gif

To Remove:
  1. Remove the air distributor assembly.
  2. Unclip the defroster valve actuator from the air inlet.
  3. Disconnect the defroster valve actuator from the valve.
To Install:
  1. Disconnect the defroster valve actuator from the valve.
  2. Clip the defroster valve actuator from the air inlet.
  3. Install the air distributor assembly.
Heater/Bi-Level Actuator 1996 – 1999 1996 – 1999 HVAC Actuators gm-10-00-1840.gif

To Remove:
  1. Remove the air distributor assembly.
  2. Remove the clip and the screws that fasten the 2 halves of the air distributor assembly and separate the air distributor assembly.
  3. Unclip and disconnect the heater/bi-level actuator from the valve.
To Install:
  1. Connect and clip the heater/bi-level actuator to the valve.
  2. Fasten the 2 halves of the air distributor assembly together and torque the fasteners to 13 in-lbs (1.5 Nm).
  3. Install the air distributor assembly.
---
Removal & Installation Recirculation Actuator 1996 – 1999 1996 – 1999 HVAC Actuators gm-10-00-1840.gif

To Remove:
  1. Remove the left sound insulator panel.
  2. Disconnect the vacuum hose from the recirculation actuator.
  3. Remove the recirculation actuator from the valve.
To Install:
  1. Connect the recirculation actuator to the valve.
  2. Clip the recirculation actuator to the air inlet.
  3. Connect the vacuum hose to the recirculation actuator.
  4. Install the left sound insulator panel.

Aug 13, 2010 | 1997 Buick LeSabre

1 Answer

Secondary air injection system


This is a pump that sits underneath your front bumper on the passenger side. It is about the size of a baseball and has two hoses going into it. I would suggest you replace it yourself as it would cost you about $360.00 if you were to go through the dealer.

Water intrusion is what will typically kill these electric pumps. There is a Technical service bulletin (#04-06-04-015) Regarding this problem, according to the tsb, you will need a new pump and there is a hose assy. #12590627) that has you reroute the pump from future water intrusion or it is guaranteed to fail again.

Although I have had water in the pump I did not see any indication of the inlet hose as the cause. It was suggested that the one way metal check valves ($15.00) that mount to the rt & lt exhaust manifold are worn and allow water from the exhaust to get sucked back into the pump. I first replaced the pump and within a week of dry weather driving the light came back on. I checked the pump and it was again full of water. I just replaced the valves which had deteriorated on the inside. So hopefully this will eliminate the problem. Note - The valves are impossible to remove without removing the 1/2 tubes (held on with 2 nuts) they are attached to the manifold with. The valve threads seize to the tube thread and had to be clamped in a vise to remove - I actually had to hacksaw the valve section to get it off the pipe. Careful as not to damage the threads.

Good luck and try autopartsdirect2you for a new pump and it has life time warranty.

TSB #04-06-04-015 - (Mar 22, 2004)

Condition
Some owners may comment on the check engine light being illuminated. Upon investigation, the technician may find a DTC P0410 indicating that there is a concern in the secondary air injection system.

Cause
Water may have collected in the AIR pump or the vent solenoid and frozen or corroded the pump.

Correction
Replace the AIR pump and install a new inlet hose and solenoid tube assembly using the following procedure:

Prep vehicle.
Raise vehicle on hoist.
Remove shield covering AIR pump.
Remove hose and vacuum lines from pump and solenoid.
Remove AIR pump inlet hose. Do not re-use.
Disconnect electrical connectors from pump and solenoid.
Remove pump mounting bolts and pump.
Transfer isolators from the old pump to the new pump.
Install new AIR pump and bolts to vehicle.

Tighten
Tighten the bolts to 17N·m (12.5 lb ft)

Route new hose assembly up between engine and fender. It should come up near the area between the battery and the coolant bottle.
Connect new inlet hose to pump inlet.
Connect old outlet hose to pump outlet.
Connect electrical connector to pump.
Connect electrical connector for solenoid to connector on the new hose assembly.
Connect the hose with the white nipple to the vacuum source hose.
Connect the remaining hose to the shut off valve.
Install shield covering AIR pump.
Lower vehicle.
Remove coolant reservoir nut nearest the battery.
Route new hose assembly between the battery and the coolant reservoir with the solenoid on top.
Install the solenoid bracket onto the coolant reservoir stud and reinstall the nut back into the vehicle.
Use a wire tie to keep the new hose assembly away from the engine. On four cylinder engines, tie to the AIR outlet hose. On six cylinder engines, tie to an available hole in the radiator fan shroud.

12590627 Hose Assembly - Secondary Air Injection

12568324 Pump, Secondary Air Injection for 2001 L35 + 2000-2003 L43/LN2

12560095 Pump, Secondary Air Injection for 1999-2000 L35

Hope that helps

Mar 06, 2010 | 2001 Chevrolet Blazer

2 Answers

2001 Trooper turbodiesel oil pressure gauge


check oil pressure with test gauge from near large engine oil filter and cooler assembly, to rule out sender unit issue, if same readings check oil pick up sucking air O ring leaking?
releif valves in oil filter cooler assembly, stuck/jamming open?
if vehicle has been sitting for a couple of days and this happens light should only stay on 1-2 seconds go out and then gauge starts reading
have seen this on older higher km vehicles bad ones have balance shaft centre journal in sump worn out (new sump)

Sep 18, 2008 | 2001 Isuzu Trooper

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

37 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8140 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...