Question about 2006 Chevrolet Impala

1 Answer

Remote door unlock problem

I have to stand very close to the car doors for my remote to open or lock odors. I have replaced the battery in remote.

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Greenhorn:

    A rookie expert who has answered 20 questions on their first day.

    Cheetah:

    An expert who has answered 20 or more questions within one hour.

  • Expert
  • 109 Answers

Check solder joints for cracks.

Posted on Dec 26, 2013

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

SOURCE: remote lock for back doors and rear tail gate door

Actually I found a solution. I remove the lock relay form the fuse panel and placed it back in place. I did not replace it. After doing this they worked. I probably need to replace the relay at some point, but for now that solved the problem. It was hard for me to believe that there is a separate relay for the lock and unlock circuit.

Posted on Sep 29, 2008

jim178
  • 207 Answers

SOURCE: 2006 Malibu: It had been taking me longer and

I have the exact same problem. When I went to a chevy dealer today,they told me when they tested it that who ever replaced the battery busted the solder on the door lock and unlock buttons. So now I am looking for a new one.They are 50 dollars cheaper on the web I hear.

Posted on Mar 31, 2009

  • 14036 Answers

SOURCE: My battery is dead. The doors are locked so the

where are your ignition key.most of the time the ignition key opens the car if the remote stop working ..if your keys lock inside. vechicle .you got to call a lock smith.or go to dealership give them your car serial number.

Posted on May 16, 2009

  • 233 Answers

SOURCE: Remote Door Lock/Unlock will not work.

At first look, I would have guessed that your battery in the door opener was dead, but that is not the case. I suggest driving to a nearby Chevy dealer and ask one of the salesman if he/she can help. They have always been helpful to me. If not try another one as they are in business to sell not only cars, but service also. They will be your best bet to fixing it. :D

Posted on Jun 08, 2009

  • 68 Answers

SOURCE: 2008 chevy malibu. cannot unlock doors from dirver

Intermittent door ajar switch contacts.

Posted on Mar 05, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Having trouble with keyless remote control on 1993 lexus es300. Replace battery on remote- still not openning doors. Help Please!


Try reporgraming it

1. Start with key out of ignition, drivers door is open all others closed and
drivers door is unlocked.

2. Insert key into the ignition (Do NOT Turn) and Pull key out.
3. Perform these steps within 40 seconds.
A. Using the power lock switch on the drivers door, perform 5 lock/unlock cycles
starting with lock. Use an even pace and try to go about one cycle per second.
(1Cycle = 1 lock and 1 unlock).
B. Close, then open drivers door.

4. Perform these steps within 40 seconds.
A. Using the power lock switch on the drivers door, perform 5 lock/unlock cycles
starting with lock. Use an even pace and try to go about one cycle per second.
(1Cycle = 1 lock and 1 unlock).
B. Insert the key in the ignition cylinder.
C. Turn the ignition to ON (Do NOT Start) then back to OFF.
D. Remove the key from the ignition.

5. Press any button on remote for a minimum of 1 second.
System should now lock and unlock doors once.

6. Close and open drivers door.

7. Press any button on remote for a minimum of 1 second. System should now lock and
unlock doors. Once to confirm programming, twice to indicate programming failed.

8. Repeat steps 5, 6 and 7 for additional remotes.

Jan 02, 2013 | Cars & Trucks

1 Answer

My Toyota 2001 rav4 remote light stays on it does nt open the doors alarm does not activate


Hi,
The light for the keyless remote fob stays on? If so the battery may need replaced.

Here is link to a remote - LINK.IF this is yours get a battery @ your grocery store.

-open the key fob w/a flat screwdriver
-note the battery's position - is the '+' or the '-' visible?
-replace the batter the same way
-snap the cover back on

To reprogram (should also be in the Owner's manual):

1. Start with the key out of the ignition, drivers door is open all others closed and
drivers door is unlocked.

2. Perform these steps within 5 seconds.
A. Insert the key into the ignition(Do NOT Turn) Pull key out.
B. Insert the key into the ignition(Do NOT Turn) Pull key out.

3. Perform these steps within 40 seconds.
A. Close then open the drivers door.
B. Close then open the drivers door.
C. Insert the key into the ignition(Do NOT Turn) Pull key out.

4. Perform these steps within 40 seconds.
A. Close then open the drivers door.
B. Close then open the drivers door.
C. Close the drivers door
D. Insert the key into ignition and leave it in ignition.
E. Turn the ignition to ON (Do NOT Start) then back to OFF.
F. Remove the key from the ignition.

5. Within 3 seconds, the power door locks should lock then unlock automatically
indicating successful entry into programming mode.
Return to step 1 if the locks do not cycle at this point.

6. Perform these steps within 40 seconds.
A. Press the lock and unlock buttons on the remtoe simutaneously for 1.5 seconds.
B. Immediately after letting go of the lock and unlock buttons,
Press the lock button by itself and hold for 2 seconds. Within 3 seconds, the door
locks should lock and then unlock once indicating successful programming. If
the door locks cycle twice, repeat steps A and B in step 6 as the remote was
not accepted.
C. Repeat steps A and B in step 6 for each new remote.

7. Open drivers door.

Oct 18, 2012 | Cars & Trucks

1 Answer

We have 2 remote key pads and replaced the batteries. Still not working. the 2 car keys will not open the doors. we never used keys to open the doors. Now we are totalling locked out of the car. Any...


TO SYNCHRONIZATION REMOTES WHEN REPLACING BATTERIES,STAND 5 FEET OF THE VECHICLE.PRESS REMOTE TRANSMITTER LOCK AND UNLOCK BUTTONS SIMULTANEOUSLY FOR 7 SECONDS.HORN SHOULD CHIRP TO CONFIRM SYNCHRONIZATION.

May 18, 2011 | 2002 Buick LeSabre

1 Answer

I bought a new Keyless remote for a 2007 Forester from a Subaru Dealer to replace an original one that went bad after 2 years. I have followed the directions in the owner's manual to program it, but can't...


IMPREZA: 2005, 2006, 2007 and
FORESTER: 2005, 2006, 2007, 2008
Check for Immobilizer key on Forester XT models only.
information is always subject to change and correction imp05keylessremote1.jpg
new remote for 2005 Imprezas.
This is not the same remote as the 05 Legacy/Outback remote which also has truck/gate release on the front and a red panic button on the back.
Lock: press Lock button for 2 seconds or so to lock car, and arm optional security system. The car with chirp once and turn signals flash for locked, 5 short chirps and signal flashes if any door is not fully closed. The dome light goes on for 15 seconds and ignition key ring (if present) will light for 30 seconds when unlocked.
Unlock: press unlock one time for driver's door, press again within 5 seconds to unlock all doors inkling rear gate (wagon). The system does not open the trunk.
Panic mode: press and hold lock button for approx. 3-4 seconds to activate Panic mode. I panic model the horn honks and turn signals flash until either the lock or unlock button is pushed again.
Finder mode: Press lock button 3 times within 5 seconds to activate Vehicle Finder mode. The horn will honk once and the turn signals will flash 3 times
Distance: works within approx. 30 feet depending on battery strength, nearby concrete walls and etc.
Audible Chirp On-Off: the system will chirp when locked or unlocked. To turn OFF the chirps, unlock the door and then push both lock and unlock buttons at the exact same time for 2+ seconds. There will be 2 chirps indicating the the audible is off. To turn the chirp back on, repeat the process and the system will chirp one time when it is back on.
Battery: as the battery ages it will only work as you get closer to the car. When a battery is replaced, the transmitter must be re-synchronized with the Keyless control unit. To synchronize, press the lock or unlock button 6 times.
Programming: 4 codes may be programmed.
Sit in driver's seat and unlock all doors. Open and close the driver's door
Turn the ignition key from LOCK to ON position 10 times within 15 seconds. Be sure to stop at both lock and on. The horn will HONK once to indicate transmitter programming mode is activated. Leave key in LOCK position and don't remove it from ignition.
You now have 45 seconds to complete the programming as below.
Open and close driver's door again.
Push either lock or unlock button on the remote you want to program. The horn will honk 2 times when successful.
To continue and program other remotes at the same time: open and close the driver's door and push lock or unlock on the remote. The driver's door must be opened and closed between each remote you want to program.
Done programming? remove the key from the ignition and the horn will honk 3 times.
DELETE old codes? Reprogram 4 times, it will overwrite old codes.
Alarm Security System: optional on all models. When locked there is one chirp (can be turned off, see above), the turn signals will flash and the red 'security' light will start to flash once every 2 seconds except for STi which flashes twice every 2 seconds.
There will be 5 chirps if a door, hood, and trunk or gate is not fully closed
You can also arm the system by using the power lock button on the driver or passenger door as you get out of the car and then closing the door behind you.
Disarm the system: push unlock for 2 seconds
Lost remote, alarm activated? When you can't use a remote to turn off the system: open the door with a key or try to start the car and the horn will start to honk. Turn the key on-off 3 times within 5 seconds and the alarm will go off and you can start the car. It's simple!
VALET mode: To set valet mode or just to disable the security alarm system: 1. unlock all doors 2. physically open the driver's door 3. hold the UNLOCK button on remote for 2+ seconds. The red 'security' light will then flash 2 times a second until the car is turned on.
System has been Tripped (except for STi): if you unlock the door with the remote and it chirps the signal light flash 4 times, the system has been triggered;
Identification mode: To find out what happened and why the system was triggered:
Open and drivers door, leave it open. Turn ignition key from LOCK to ON 2 times and then leave in LOCK position.
Tripped code: 1 security light flash: a door has been opened, 3 flashes when the impact sensor was triggered, 4 flashes when the ignition was messed with or battery disconnected

Nov 19, 2009 | 2007 Subaru Forester 2.5X L.L. Bean...

3 Answers

The Lexus car remote key control model ES300


try this:

1. Start with key out of ignition, drivers door is open all others closed and
drivers door is unlocked.

2. Insert key into the ignition (DO NOT Turn) and Pull key out.
3. Perform these steps within 40 seconds.
A. Using the power lock switch on the drivers door, perform 5 lock/unlock cycles
starting with lock. Use an even pace and try to go about one cycle per second.
(1Cycle = 1 lock and 1 unlock).
B. Close, then open drivers door.

4. Perform these steps within 40 seconds.
A. Using the power lock switch on the drivers door, perform 5 lock/unlock cycles
starting with lock. Use an even pace and try to go about one cycle per second.
(1Cycle = 1 lock and 1 unlock).
B. Insert the key in the ignition cylinder.
C. Turn the ignition to ON (Do NOT Start) then back to OFF.
D. Remove the key from the ignition.

5. Press any button on remote for a minimum of 1 second.
System should now lock and unlock doors once.

6. Close and open drivers door.

7. Press any button on remote for a minimum of 1 second. System should now lock and
unlock doors. Once to confirm programming, twice to indicate programming failed.

8. Repeat steps 5, 6 and 7 for additional remotes.

Mar 23, 2009 | 1997 Lexus ES 300

1 Answer

Door remote does not work


change the battery and then reset it by standing close to the vehicle and hold the lock and unlock at the same time until the doors lock and unlock and then you should be all set

Mar 11, 2009 | 2000 Honda Accord

2 Answers

My Honda CR-V EX 2005 doors lock by themselves. Occasionally, after you unlock it with the remote key, it locks itself before you can get in. It also happens sometimes when I unlock the car, then open the...


They all do it, its part of the security system that all the doors lock after a minute or so from unlocking if you don't open the driver's door.
It prevents you from accidentally unlocking the car door while walking away and clicking the remote in your pocket, the car re-locks on its own.
If you open with the remote then open only the rear door, the other doors all lock and when you close the rear the alarm goes off.
What fun we have!


Jan 02, 2009 | 2003 Honda CR-V

3 Answers

Program remote control for mazda mpv 2002


Courtesy of: forums.mazdaworld.org

Try this, it works on several 2002 models:


Step 1: Open drivers door and leave open.

Step 2: Lock and unlock the drivers door using the power door lock switch on the door.

Step 3: Insert key into the ignition.

Step 4: Turn key to on position and return to off position. (IMPORTANT - use ON position NOT ACC position). Do this 3 times within 10 seconds. Leave key in the ignition.

Step 5: Open and close the drivers door 3 times. (Door should be left open after this step).

Step 6: ECU should respond by locking and unlocking the doors.

Step 7: Press any button on remote #1. ECU responds by locking and unlocking the car doors.

Step 8: Press any button on remote #2 (etc.) Each time the ECU will respond by locking & unlocking the doors.

Step 9: Remove the key from the ignition and the ECU will respond a final time with a series of door locks and unlocks. You're done

Dec 06, 2008 | 2000 Mazda MPV

1 Answer

Programming keyless remote


2003-04 Mazda 6 REMOTE PROGRAMMING


Step 1: Open drivers door and leave open.

Step 2: Lock and unlock the driver’s door using the power door lock switch on the door.

Step 3: Insert key into the ignition.

Step 4: Turn key to on position and return to off position. (IMPORTANT - use ON position NOT ACC position). Do this 3 times within 10 seconds. Leave key in the ignition.

Step 5: Open and close the driver’s door 3 times. (Door should be left open after this step).

Step 6: ECU should respond by locking and unlocking the doors.

Step 7: Press any button on remote #1 twice. ECU responds by locking and unlocking the car doors.

Step 8: Press any button on remote #2 (etc.) twice. Each time the ECU will respond by locking & unlocking the doors.

Step 9: Remove the key from the ignition and the ECU will respond a final time with a series of door locks and unlocks. You're done!

Good Luck.

Jul 12, 2008 | 2003 Mazda Mazda6

Not finding what you are looking for?
2006 Chevrolet Impala Logo

38 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75807 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22133 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8172 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...