Question about Cars & Trucks

1 Answer

Lil rider 80 kb901

Plastic wheel pipe is missing

Posted by on


1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 6 Answers

With the rapid of developing, more and more plastic generated. how can we do with these so many wastes. tires, plastic rubber???

Posted on Dec 30, 2013


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Looking for Greenfield Fastcut 32 Ride on lawnmower replacement Steering wheel no.GT 2380 The plastic housing which connects to steering column has totally given up. Where can I get one?

sort of the boss kit like on cars holding it to the spline or shaft

see if the steering wheel of a newer green field model fits
wanted ads online
a rider mower workshop may be wrecking a unit




Apr 12, 2017 | Cars & Trucks

1 Answer

Lil rider 80-kb901

The most common cause of a non-starting car is the battery. It is either weak, (low voltage) dead, (zero voltage) or has bad connections. (corroded or loose) I will assume you have a fully charged battery with good connections. (both to battery and starter relay)
If you remove the starter switch lead (small wire) from the starter relay and apply +12v from the battery to its respective prong or lead on the relay, and your starter cranks, your starter switch is faulty. (not to be confused with your key switch). If you jump the two large wires together on the relay and it cranks, then the relay is faulty. If you jump the two large wires together and nothing happens, then starter is faulty, or wires to starter are loose or broken. Picture of starter switch prong on the relay is pictured. NOTE: sparks are to be expected, so don't be too scared.

Dec 16, 2013 | Cars & Trucks

1 Answer

Replace driver airbag on 1997 Chevy Malibu

screws on the back of steering wheel covered with lil plastic screw hole covers

Jan 04, 2013 | 1997 Chevrolet Malibu

1 Answer

Need to know the torque setting for the rear weel bearing on my 2001 ford focus. it takes a 30mm socket.

The torque setting 49 ft. lbs.

Torque Specifications
Description Nm lb-ft lb-in Wheel nuts - steel/alloy wheels 128 94 - Wheel spindle retaining nuts 66 49 - Wheel cylinder retaining bolts 12 9 - Rear brake pipe to wheel cylinder union 8 - 71 Rear wheel speed sensor retaining bolt 9 - 80 e0001241.jpg
Item Part Number Description 1 - Tie bar and knuckle 2 - Backing plate 3 - Wheel spindle 4 - Sensor ring - anti-lock control 5 - Grease cap 6 - Wheel bearing retainer 7 - Drum

Apr 26, 2011 | Ford Focus Cars & Trucks

1 Answer

I have a jag s type 2000 model 3.0 let me start of from the beging when i had it at first it a lil miss all around but it was not bad mybe like a small vacuum leak in it. so my first thought was to get all...

You really need to rework the plugs and coils as this seems, from what you say, is where the problem has grown from. Also check that the inlet manifold and all pipes in this area are sound. If the fault code shows a misfire then careful inspection of each unit and its associated wiring and connections, may show a faulty component and perhaps the substitution of of a new coil and plug in each position in turn, may identify the faulty unit.
hope this helps - good luck.

May 03, 2009 | 2003 Jaguar S-Type

1 Answer

Fuelin up my ford escape

In left rear wheel well under a plastic cover is your fill and vent pipe
A coupling from plastic pipe to metal pipe must be taken apart and air blown into tank
This plastic line is bent down and collects overfill and moisture, thus not allowing tank to to vent as you fill.
Once you have cleared plastic line and reassembled coupling , gently bend metal pipe so plastic line drains towards tank.
Manufactures fopa

Oct 26, 2008 | 2005 Ford Escape

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

67 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts


Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides