Question about 2001 Ford Taurus

1 Answer

Side mirror broke off in small accident. Now, when I hook up a new battery (old 1 drained) Horn blows, wipers run on high and washer fluid blows out

I thought I needed a new battery because I couldn't even jump start the old 1. I install the new one and the terminal archs and the horn blows, wipers run on high and the washer fluid empties.

Posted by on

  • Garry White
    Garry White Dec 25, 2013

    Roberta, this is a sedan, there is no rear wiper. I've already changed ther relays. I included the fact that the outside mirror is broken off thinking someone would confirm my suspicion of a short and where exactly it might be. Thank you Jason Philips, I'll be checking the stering column next. Regardless, I REALLY apprecviate all the feedback from everyone. Thank you!!

×

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Ford Master
  • 3,103 Answers

The mirror got broke off and what else got involved in the issue? like maybe the front of the door got crunched into the dash?..

Posted on Dec 26, 2013

Ad

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
jaysonemanme
  • 500 Answers

SOURCE: I have a 2004 Ford Ranger. In July 2010 I took it

i am a tech at a ford dealership. it sounds like you have a short some wheres around your steering column that maybe what we call "backfeeding" to other systems. the area where the tilt is on the steering column is a good place to check. also remote starters can cause alot of havoc on a vehicle.

Posted on Jan 19, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Looking for the fuse for the wiper motor 2008 chevy impala


WPR fuse 25amp under hood fuse box .
Wiper/Washer System Components
The Wiper/Washer System consists of the following components:
• Windshield wiper/washer switch
• Body control module (BCM)
• Wiper PCB relay
• Wiper high PCB relay
• Windshield wiper motor
• Windshield washer fluid pump
• Windshield washer fluid level switch
• WPR fuse 25 A
• WSW fuse 10 A
This is more then likely not a fuse issue !!!!!!!
Low Speed Operation
When the wiper switch is in the low speed position, ground is applied through the switch internal resistor and the wiper switch low signal circuit to the body control module (BCM). In response to this signal, the BCM energizes the WIPER PCB relay by applying battery voltage through the wiper relay control circuit to the coil side of the relay. This allows battery positive voltage from the WPR fuse to flow through the switch input side of the WIPER PCB relay and out to the switch input side of the WIPER HIGH PCB relay. Since the wiper high relay is de-energized and its switch contacts are normally closed to the low speed control circuit of the windshield wiper motor, the motor will operate at low speed.
Wiper motor low speed operation and the wiper PCB relay can also be commanded ON/OFF by using a scan tool. Refer to Control Module References.
The PCB relays mentioned above are soldered right into the circuit board inside the fuse/relay block under the hood . There are alot of reasons for the wipers not to work ! The fuse could be blown but fuse's don't just blow for no good reason , short to ground , low resistance high current flow etc.... Intermittant !

Power and Grounds
With the ignition in the ON position, accessory voltage is supplied through the 25A WPR fuse to the WIPER PCB relay, the WIPER HIGH PCB relay and the WS WASH PCB relay that are all located in the underhood fuse block. Refer to Wiper/Washer Schematics.
G200 provides ground for the windshield wiper motor and the WIPER PCB relay. G100 provides ground for the windshield washer fluid pump and the windshield washer fluid level switch.

Dec 04, 2016 | Cars & Trucks

1 Answer

Which fuse controls front windshield wiper pump


Do the wipers work ? Fuse for wipers is same as washer pump .
Principles of Operation
The wiper motors receive inputs from the following:
  • Multi-function switch
  • Powertrain control module (PCM)
  • Ignition switch
  • Smart junction box (SJB)
The following components are integrated in the wiper motors:
  • Windshield wiper motor module
  • High/low speed relay
  • Run/park relay
  • Washer pump relay
  • Park sense (Hall-effect sensor)
Washer System
The windshield washer and the rear window washer are activated by the internal wiper motor modules when it receives a ground from the multi-function switch between the washer inputs. Depending on the correct ground, the internal wiper motor modules activate either the windshield washer or rear window washer relays (internal) by grounding the respective relay coil. When either module is activated, it connects voltage to the washer pump while the deactivated module provides ground to the washer pump. In this manner, voltage polarity is reversible to achieve directional change of the washer pump and washer fluid.
  • The washer pump is inoperative
  • Circuitry
  • Washer pump
  • Multi-function switch
  • Windshield wiper motor
  • Rear window wiper motor
  • Go To Pinpoint Test I .
Does your expedition have programmable/recall memory option for seats an mirrors ?
Driver Seat Module
The power driver seat and power exterior mirrors are controlled by the driver seat module (DSM) only when the vehicle is equipped with the programmable/recall memory option.
On the Expedition Limited, the power fold exterior mirror option is controlled by the DSM. Before running a self-test or retrieving codes, the power fold switch must be inactive for at least 30 seconds.
This is a complex vehicle , electronics , control modules an serial data communication networks. You mite be better off taking it to the dealer or some other repair shop . There could be DTC'S - diagnostic trouble codes stored in the SJB - body control module !
B1667 Mirror Driver Up/Down Motor Stalled Go To Pinpoint Test D . B1668 Mirror Driver Right/Left Motor Stalled Go To Pinpoint Test D . B1669 Mirror Passenger Up/Down Motor Stalled Go To Pinpoint Test D . B1670 Mirror Passenger Right/Left Motor Stalled Go To Pinpoint Test D . B1735 Mirror Driver Vertical Switch Circuit Short to Battery Go To Pinpoint Test D . B1739 Mirror Driver Horizontal Switch Circuit Short to Battery Go To Pinpoint Test D . B1743 Mirror Passenger Vertical Switch Circuit Short to Battery Go To Pinpoint Test D . B1747 Mirror Passenger Horizontal Switch Circuit Short to Battery Go To Pinpoint Test D . B2312 Mirror Horizontal Feedback Potentiometer Circuit Failure Go To Pinpoint Test D . B2314 Mirror Passenger Horizontal Feedback Potentiometer Circuit Short to Battery Go To Pinpoint Test D . B2316 Mirror Passenger Vertical Feedback Potentiometer Circuit Failure Go To Pinpoint Test D . B2318 Mirror Passenger Vertical Feedback Potentiometer Circuit Short to Battery Go To Pinpoint Test D . B2320 Mirror Driver Horizontal Feedback Potentiometer Circuit Failure Go To Pinpoint Test D . B2322 Mirror Driver Horizontal Feedback Potentiometer Circuit Short to Battery Go To Pinpoint Test D . Normal Operation During normal operation, when the front wiper wash is selected, the windshield wiper motor provides power to the washer pump through circuit CRW14 (BU/WH) and ground is provided to the washer pump through circuit CRW12 (GY/OG) and the rear wiper motor. If rear wiper wash is selected, the rear wiper motor provides power to the washer pump through circuit CRW12 (GY/OG) and ground is provided to the washer pump through circuit CRW14 (BU/WH) and the windshield wiper motor.
    Possible Causes
  • Multi-function switch
  • Open in circuit CRW14 (BU/WH), CRW12 (GY/OG), CRW07 (GY/BN), CRW20 (GY/YE), SBB49 (RD) or GD149 (BK/GY)
  • Short to ground in circuit CRW14 (BU/WH), CRW12 (GY/OG), CRW07 (GY/BN) or CRW20 (GY/YE)
  • Washer pump
  • Windshield wiper motor
  • Rear wiper motor
    This is

Feb 02, 2016 | 2010 Ford Expedition

1 Answer

Fuse number for winderwiper


Hi Maddie, I'm glad to help! Below, I have posted a diagnostic procedure to see why the wipers are not working on your Dakota. Hope this helps and have an awesome day Maddie!



DIAGNOSIS
WIPER MOTOR

The following are wiper motor system problems,
tests to be performed to locate the faulty part, and
the proper action to be taken. If the malfunction involves
only the delay mode, switch, or wiring, see the
diagnosis for Intermittent Wipe Module and Wiper/
Washer Switch.
CONDITION
Motor will not run in any wiper/washer
switch position.
PROCEDURE

(1) Check fuse 10 in the fuseblock module. If OK,
go to step 3. If not OK, replace fuse and go to next
step.
(2) Check motor operation in all wiper/washer
switch positions. If not OK and fuse blows, go to step
5. If not OK and fuse is OK, go to next step.
(3) Place wiper/washer switch in LOW position and
listen to motor. If you cannot hear it running, go to
next step. If motor is running, check motor output
shaft. If output shaft is not turning, replace motor
assembly. If it is turning, drive link to output shaft
or linkage is not properly connected. Replace worn
parts and/or properly connect drive link to the motor
output shaft.
(4) Connect a voltmeter between motor terminal L
and ground strap (Fig. 1). If there is little or no voltage
(less than 1 volt), move negative test lead from
the ground strap to battery negative terminal. If an
increase in voltage is noticed, the problem is a bad
ground circuit. Make sure the motor mounting is free
of paint and that mounting fasteners are tight. If
there is still no indication of voltage, the problem is
an open in wiring or faulty wiper/washer switch. If a
small increase (greater than 3 volts) in voltage is observed,
the problem is a faulty motor assembly.
(5) Disconnect motor wiring connector and replace
fuse. If fuse does not blow, motor is defective. If fuse
blows, wiper/washer switch or wiring is at fault.
CONDITION
Motor runs slowly at all speeds.
PROCEDURE

(1) Disconnect wiring harness connector at motor.
Remove wiper arms and blades. Connect an ammeter
between battery and terminal L on motor (Fig. 2). If
motor runs and average ammeter reading is more
than 6 amps, continue to next step. If motor runs
and average ammeter reading is less than 6 amps, go
to step 3.
(2) Check wiper linkage or pivots for binding or obstruction.
Disconnect drive link from motor. If motor
now runs and draws less than 3 amps, repair linkage
system. If motor continues to draw more than 3
amps, replace motor assembly.
(3) Check motor wiring harness for short between
high and low speed circuits. Connect a voltmeter or
test lamp to motor ground strap. Set wiper/washer
switch to LOW position. Connect other lead of voltmeter
(test lamp) to terminal H of the wiring harness.
If voltage is present, there is a short in the
wiring or wiper/washer switch. If no voltage is
present, go to next step.
(4) Set wiper/washer switch to HIGH position.
Move voltmeter (test lamp) lead from terminal H to
terminal L of the wiring harness. If voltage is
present, there is a short in the wiring or wiper/
washer switch.
CONDITION
Motor will run at high speed, but not at low
speed.
Fig. 1 Voltmeter Between Terminal L and Ground

Motor will run at low speed, but not at high speed.
Fig. 2 Ammeter Between Terminal L and Battery
WIPER AND WASHER SYSTEMS 8K - 3

Apr 26, 2014 | 1995 Dodge Dakota

2 Answers

My windshield washer does not work


HOOK TEST LIGHT TO WASHER PUMP MOTOR ELECTRICAL CONNECTOR FIRST DISCONNECT ELECTRICAL AT WASHER PUMP MOTOR.NEED A HELP TO WORK WIPER WASHER SWITCH.IF TEST LIGHT LIGHT UP WIPER WASHER MOTOR FAULTY.IF TEST LIGHT DONT WORK.YOU HAVE FAULTY WIPER WASHER SWITCH OR FAULT IN THE WASHER WIPER POWER MODULE IF WIPER MOTOR NOT WORKING YOU HAVE A BLOWED 30 AMP FUSE OR BAD WIPER MOTOR RELAY.

May 22, 2011 | 2006 Dodge Grand Caravan

3 Answers

I oown a 1999 jeep grand cherokee laredo replaced front windshield wiper pump on resevoir but still no fluid to windshield and i can hear pump.what is my next step.


the hose going from pump to sprayer could be cloged or the sprayer it self is get small wire to unclog sprayer and check hose

Jan 19, 2011 | Jeep Grand Cherokee Cars & Trucks

2 Answers

Fuel Pump Fuse Number for a 1998 audi a4 2.8 quattro


Fuses: Fuse arrangement in fuse panel, behind instrument cluster, left
Fuse Arrangement In Fuse Panel 62624464

1 - Heated washer jets 5A 2 - Turn signals 10A 3 - Headlight washer (relay), illumination for glove
compartment, climate control, Automatic Transmission, instrument cluster 5A 4 - License plate light 5A 5 - Instrument cluster, seat heating, test connection
for cruise control, bulb monitor for auto-check display, Automatic Transmission display, switch
lighting, mirror switches and actuators, airbag
warning light, outside temperature indicator,
climate control 10A 6 - Central locking system 5A 7 - Anti-lock brake system (ABS) 10A 8 - Vacant 9 - Mirror heating 10A 10 - Vacant 11 - Cruise control (Automatic Transmission) 5A 12 - On board diagnostic system 10A 13 - Brake lights 10A 14 - Interior lights, reading lights, anti-theft alarm system, vanity mirror 10A 15 - Instrument cluster, power windows, climate control, automatic transmission 10A 16 - Anti-lock brake system (ABS), Anti-Slip Regulation (ASR) 5A 17 - Heated door locks 10A 18 - High-beam, right 10A 19 - High-beam, left 10A 20 - Low-beam, right 15A 21 - Low-beam, left 15A 22 - Side marker and tail light, right 5A 23 - Side marker and tail light, left 5A 24 - Wiper and washer system 25A 25 - Blower for heating, climate control 30A 26 - Rear window defogger, mirror heating 30A 27 - Rear window wiper 15A 28 - Fuel Pump 15A 29 - Engine timing 30A 30 - Sun roof 20A 31 - Tail lights, cruise control, automatic transmission 15A 32 - Engine timing 20A 33 - Cigarette lighter 15A 34 - Engine timing 15A 35 - Trailer recptacle 30A 36 - Fog lights 15A 37 - Radio 20A 38 - Luggage compartment light, central locking system 15A 39 - Emergency flasher system 15A 40 - Horn 25A 41 - Anti-lock brake system (ABS) 25A 42 - Vacant 43 - Vacant

Apr 05, 2010 | 1998 Audi A4

2 Answers

Need a diagram of the fuse box for a 1994 volk


Heres a picture of fusebox,and listed is the fuse locations,1) 10amp left low beam light
2)10amp rt low beam light
3)10 amp instrument& license plate light
4)15 amp, rear wiper
5)15amp frt washers and wipers
6)20amp A/C fresh air fan.
7)10amp rt tail & side marker lights
8)10amp left tail & side marker lights
9)20amp rear defroster &heated mirrors
10)15amp fog lamps.
11)10amp left high beam
12)10amp rt high beam
13)10amp horn, rad fan run on
14)15amp backup lights (m/t),power mirrors,heated seats,heated washer jets,cruise control (m/t)
15)10amp engine electronics,coolant pump run on(v6)
16)hazard signals,glove box lite,shift lite
17)10amp turn signals
18)20amp fuel pump, oxygen sensor
19)30amp a/c, rad cooling fan.
20)10amp brake lights,cruise control.
21)15amp dome light,cigar lighter,locking system,multifuntion indicator,clock,vanity mirror.a94b062.gif

Mar 10, 2010 | 2003 Volkswagen Passat

2 Answers

I have a 1998 chrysler concord and i can get windsheild washer fluid to spray the resevoir is full no fluid is leaking out the wipers activate upon initiating the spray sequence but no fluid comes out


Pull out the small tube connected to the jet the fluid comes out of and check for any kind of debris, after blowing out the tube try and activate washer before you connect the hose again if no fluid comes out of the tube than that replace the small pump connected to the resivoir thay are about $15.00

Nov 29, 2009 | 1998 Chrysler Concorde

2 Answers

The rear wiper on my '99 model exped isnt working ,ford global says its the motor and it will cost me P13k . any one who can help me find a mechanic do some repair on this?


what is P13K?

check the fuse first. dealer can hook up NGS Tester and get fault codes to see what is wrong.

Principles of Operation
NOTE: The generic electronic module (GEM) will not activate the rear wiper system if either the liftgate or the liftgate glass is ajar. If either the liftgate or the liftgate glass becomes ajar while the rear wiper is in operation, the GEM will park the rear wiper motor.
There are two distinct modes of wiper operation:
  • Off Mode: In this mode, there is no rear wiper activity, and the wiper motor will be in the PARK position.
  • Interval Mode: This mode is selected when the rear wiper switch is in either the Interval 1 or 2 position. When this mode is selected, the rear wiper motor is driven up onto the glass by activating the rear wiper UP relay. When the wiper motor HIGH/LOW/PARK position input reaches the high position, the UP relay is deactivated and the DOWN relay is activated to reverse the wiper motor direction. When the wiper motor reaches the LOW position, as determined by the HIGH/LOW/PARK position input, the GEM deactivates the DOWN relay and will begin a new wiper cycle 1 to 10 seconds later, depending on the interval position selected.
To engage the rear window washer, rotate the rear window washer selector downward to the WASH position. The rear window wiper will run as long as the WASH position is selected. When the rear window washer selector returns to the OFF, INT 1 or INT 2 position, the washer will stop immediately, but the rear window wiper will continue for two to three sweeps and then return to its previous mode of operation.
The low washer fluid indicator chime warns that the washer fluid level is low. The low washer fluid indicator chime is a single tone with a duration of one second. The chime will sound when the low washer fluid indicator is initially activated.
The low washer fluid indicator warns that the fluid level in the washer reservoir is low. The low washer fluid indicator will illuminate when the washer fluid level is low and the ignition switch is in the RUN position.
The low washer fluid indicator will deactivate when the washer fluid reservoir is filled and the ignition switch has been cycled from RUN to OFF, then to RUN.
Inspection and Verification
  1. The wiper/washer system is a generic electronic module (GEM) controlled system; refer to Section 419-10 .
  1. Verify the customer concern by operating the wiper/washer system.
  1. Visually inspect for obvious signs of mechanical and electrical damage.


Visual Inspection Chart Mechanical Electrical
  • Hoses to windshield washer pump
  • Wiper linkage
  • Fuses 6 (5A), 8 (5A), 15 (5A), and 20 (5A)
  • Wiring harness
  • Loose or corroded connector(s)
  • Relays
  • Motors
  • Multifunction switch
  • Washer fluid level switch


----------------------------------------
  • The wipers are inoperative — rear
  • Fuses 6 (5A), 8 (5A), 15 (5A), and 20 (5A).
  • Circuitry.
  • GEM.
  • Multifunction switch (wiper/washer switch).
  • Rear wiper up relay.
  • Rear wiper down relay.
  • Rear wiper motor.

May 12, 2009 | 1999 Ford Expedition

1 Answer

2005 ford expedition rear wiper


Sounds like a problem within the wiper motor not turning off at rest or not reaching it's rest point to be able to turn itself off, probably needs a new motor. Disconnecting it should have no relation to the front washer operation, you can confirm this by reconnecting the wiper motor to try.

Apr 12, 2009 | 2005 Ford Expedition

Not finding what you are looking for?
2001 Ford Taurus Logo

68 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5520 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...