Question about 2003 Hyundai Tiburon

Open Question

Replace rear wheel bearing hub 2007 Hyundai Tiburon

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 393 Answers

SOURCE: replacing rear wheel bearings on 1999 hyundai sonata

  1. for drum brakes with sealed hub(all one piece) remove lug nuts and wheel.
  2. spray penetrating oil around studs if there is a big phillips head screw visible remove it with impact driver/if not use big ballpeen hammer ,tap on flat of drum near studs(becareful not to hit them) until drum loosens(your creating a shockwave to loosen rust)
  3. once drum is off there are 4-bolts coming in from behind backing plate, remove them then hub should be able to be removed w/a little persuation from hammer.
with out sealed hub ,
  1. remove wheel
  2. remove dust cap,cotterpin,star washer(if equipped) do not re use cotter pin
  3. remove nut then washer, wiggle brake drum and front bearing will come out.
  4. put nut on shaft tighten 2-3 turns grab drum by sides and pull towards you this should remove drum leaving inner bearing/seal on shaft
  5. to replace reverse procedure making sure to pack new bearings w/grease(take drum and use long punch to remove bearing races, use race/seal installer to install new races
with disk brakes

  1. remove wheel
  2. remove caliper/bracket
  3. remove rotor
  4. remove 4-bolts from behind,tap old hub out
  5. reverse procedure



Posted on Nov 15, 2008

Ad
emissionwiz
  • 77201 Answers

SOURCE: Change front wheel bearings

u will need to remove the brake cailper and the the brake rotor, then the hub retaining nut, that is a large metric nut, the bearing and hub must come off, then u will need to take this hub to a machine shop or the dealer and have the new bearing pressed in.
BCA/NATIONAL Part # 510078 moreinfo.gif {Ball Bearing Bore=1.5354" Outer Diameter=2.9134" Width=1.4173"}
Front Wheel PRICE: $47.99, PART SOURCE: Rockauto.com

3bcf37f.jpg

Posted on Mar 12, 2009

michigan man
  • 3533 Answers

SOURCE: Rear wheel bearings on Hyundai Accent

no i do not believe they are press in there are held in by a seal try www.autozone.com to see if they have your car listed if they do you will be able to get a diagram showing you how they come a part.

Posted on Apr 24, 2009

  • 5 Answers

SOURCE: how to replace 2004 hyundai sonata rear wheel bearing

the work grade ,tutorials,estimate and tools needed are posted on "All DATA" which you will find in most local library .dealers ,mechanics and shops use it as a reference .
good luck!

Posted on Feb 16, 2010

  • 171 Answers

SOURCE: how to replace 2002 hyundai elantra hub and bearing

With the car on ground, break loose the drive-axle nut, and the wheel nuts , than jack up the car, support it properly, remove the wheel ,remove the axle-nut.
Remove the brake caliper assembly-- support it properly.
Remove the two bolts that hold the hub bracket to the Macpherson strut assemble, remove the lower arm ball joint and remove the steering tie- rod ball-joint attached to the hub bracket. That's it.Slide off the hub /with the bracket off the drive-shaft.
Follow steps backwards to assemble back.

Posted on Apr 09, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I was told the rear right hub bearing went out, so i ordered one from auto zone but it doesn't fit. It is to loose what do i do?? Also when i back up the car makes some really loud noises. (this just...


1st, take the hub bearing back to AutoZone and either get you money back or get them to order or give you the right size bearing. The noise you are having could be from that bearing.... ya think?

Sep 05, 2011 | 2006 Hyundai Tiburon

1 Answer

HIT A CURB WITH THE RIGHT REAR WHEEL AND HAVE HAD AN ESTIMATE TO REPLACE THE STRUT ASSEMBLY AND RIGHT REAR KNUCKLE AXLE CARRIER. HAVE TRIED TO PRICE PARTS FROM THE DEALER AND THEIR PARTS BREAKDOWN DON'T...


the repair shop probably is listed in assembled units like bearing and hub unit whereas the dealer lists the parts separately, hope this helps

Aug 06, 2010 | 2007 Hyundai Tiburon

1 Answer

How do i remove the rear wheel hub so i can replace the worn out wheel bearing


hi from uk to remove rear hub/s you have to remove the bolts that secure the hub and brake backplate to th axle these hubs come complete with bearing and is not normally the case of replacing the actual bearing ? and this type of hub is becoming common fitting on lots of vehicles like hyundai/ford/vauxhall etc hope this helps ?

Feb 22, 2010 | 2002 Hyundai Accent

2 Answers

Rear wheel bearing hyundai coupe


just remove the wheel and count the teeth on the ring on the rear brake thats all you need to do. Since you can't drive it take it off and take it in to compare parts so you don't have to go back twice. You will need a new wheel seal and race and bearings.

Sep 29, 2009 | 2001 Hyundai Tiburon

1 Answer

Wheel bearing


The front 'hub' bearing is 'pressed' out. You have to remove the steering knuckle from the vehicle and using a hydraulic press, replace the bearing by pressing out the old one and then pressing in the new one.

Sep 07, 2009 | 2003 Hyundai Tiburon

1 Answer

What does it take to replace the front wheel bearings on a 2003 Tiburon


the front wheel bearings on your car are not sold except as a front wheel hub assembly with the bearing pre-installed, they run about $100.00 each, to replace them requires no special tools, all u do is remove the wheel, the brake caliper and the brake rotor and the hub nut, then the hub just slides off, u will most likely need a very large socket for the hub retaining nut.

Jul 05, 2009 | 2003 Hyundai Tiburon

2 Answers

Can not get the rotors off my 97 hyundai tibaron


Hyundai Tiburon 96-01 uses a outer hub system. To replace front rotors. You'll need front bearings as well. The bearing and hub will need to be pressed out of the spindal. Then replacement of bearing will need to be pressed in. From a shop.Or they can use a slide hammer to remove ,but damages the bearing. Best to buy bearing and have cash for an alignment job too.Then replace front rotors. Rotor and hub install is ez after you get bearing pressed.Rear rotor and bearing are bolt on though.

Apr 06, 2009 | Hyundai Motor 1997 Tiburon

2 Answers

Change front wheel bearings


u will need to remove the brake cailper and the the brake rotor, then the hub retaining nut, that is a large metric nut, the bearing and hub must come off, then u will need to take this hub to a machine shop or the dealer and have the new bearing pressed in.
BCA/NATIONAL Part # 510078 moreinfo.gif {Ball Bearing Bore=1.5354" Outer Diameter=2.9134" Width=1.4173"}
Front Wheel PRICE: $47.99, PART SOURCE: Rockauto.com

3bcf37f.jpg

Mar 12, 2009 | 2003 Hyundai Tiburon

1 Answer

What's involved in changing the front wheel bearings on a 2003 Hyundai Tiburon? Thank you


A whole bunch its toouch basically your overhauling that side taking off the wheel taking rotor off pulling out the hub dearing and pressing it back inlooking at approx 2-2.5 hors and then you made alignment but if you want to know exacxtly how to do this go to collisionrepairadvice.com its worth it

Mar 12, 2009 | 2003 Hyundai Tiburon

1 Answer

Front wheel bearing keeps going out


you should check the hub carrier for damage or hairline cracks ok m8

Jan 04, 2009 | 2003 Hyundai Tiburon

Not finding what you are looking for?
2003 Hyundai Tiburon Logo

Related Topics:

45 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

77194 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8743 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...