Question about Jeep Patriot

Open Question

No heat in the cabin 2009 jeep patriot - Patriot Jeep Cars & Trucks

Posted by Anonymous on

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 6982 Answers

SOURCE: amateur radio installation in 2009 jeep patriot

To run any wire through the firewall, find a spot that is both reachable and unobstructed on both sides of the wall. I generally use a very short bit so after penetrating, it does not accidentally plunge into other wiring or components, or I use a collar over the bit (a small piece of tubing, leaving only 1/4" of bit exposed) I sometimes also "cheat" by poking a hole in the rubber boot where the steering column goes through.
Whenever passing a wire through sheet metal you must install a grommet. (if none are available, you can make one by using a piece of rubber tubing or the cut off end of an old tire valve.)
When tapping power from the battery, you will need to use a relay and switch attached to the "accessory on" side of the ignition switch, to prevent whatever you are installing from remaining on after the vehicle has been turned off. Use fuses in all new power sources as well to protect the vehicle and your new install from damage.
In creating a new circuit, you have the opportunity to use shielded wire, which will prevent stray electrical "noise" in your set" not a bad idea to do that.
good luck

Posted on Oct 18, 2009

oldmanewtoys
  • 414 Answers

SOURCE: Remove & replace window cranks---- Jeep patriot 2009

you need to use a window crank removing tool and remove handle. Make sure window is all the way up before reinstalling handle on splines.

Posted on Mar 05, 2010

bczopdar
  • 9 Answers

SOURCE: Jeep Patriot 2009----reposition window crank handlel

Good question, I struggled with this very dilemma for the longest time. I tried everything short of smashing it off. I had all the panels removed and by the way there is three of the friggin things... But just couldn't get the handles off the finish it. I ended up taking it to the dealer to remove them for me. Some say that you need a handle remover tool, but I have yet to find one for sale anywhere...

Posted on Jul 08, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the interior fuse box in the 2009 jeep patriot?


open glove box, read oper guide.
under hood.
the guide tells what/s on all car made. a fact.

posted this answer over 100 times,, ever like search
most jeeps over 2007 have no cab box called JB.
has totally integrated power module under hood
RTm


http://owners.mopar.ca/en/manuals/2009/2009_Caliber_Patriot_and_Compass.pdf

Jan 28, 2017 | 2009 Jeep Patriot

1 Answer

Jeep patriot no heat


fan blows?
engine reaches and holds 180F or more , normal engine temp?
(use a IR pyro gun to measure it)
ever go a cooling system flush, if not the heater core could be packed full of junk.
id the dampers fail , its not in heat mode.
check the dampers after checking engine heat.

it only takes 2 things to make any water to air heat exchanger to work.
hot water
and actual air flow.

check for hot water first (engine coolant)

Feb 05, 2014 | 2009 Jeep Patriot

1 Answer

2009 jeep patriot not heating up properly


its a heat exhanger.
1: the water is not 180F or more.
2: the water is not flowing through the core
3: or the air cant pass through the core.
bad water temp,. bad flows, or the damper is in the wrong position.

i plug in my scan tool and the ECT reads 180f or more. holding
cool real hot water.
i then feel both water lines to the core (dial set to hot)
both are hot, if not , the core is plugged or the water valve (if present)
is clogged.
ok both lines 180f roasting hot, finger test or better IR pyro gun.,
must be damper stuck blocking core, or huge mouse nest inside.

if the core is hot, we check damper controls
there are 3 systems, and some cars have a mix
open FSM to HVAC section,, bingo there you go...
cable, vacuum servo and damper motors.
some are a mix. min 04 is mix. my jeep 08 is vacuum
my 96 is cables.
id dont matter,. there is a simple test for each
the motor kind are the hair pulling kind, (invisible)


http://www.fixkick.com/AirCond/heater.html

i went online
the patriot has at least 2 cables, blend./temp, and mode
so there is water valve, so he damper if open on temp you get
full heat, just eyes on that lever ,cable and end of cable tells
you if the door is opening.

Feb 05, 2014 | 2009 Jeep Patriot

1 Answer

2009 jeep patriot 2.4 heater not blowing hot


Go To your local Firestone store located on 1802 state st. Erie,PA

Dec 11, 2013 | 2009 Jeep Patriot 2.4

1 Answer

2009 jeep patriot transmission problems


google jeep patriot forums join one or more and post there

Feb 06, 2013 | 2009 Jeep Patriot

1 Answer

Drive belt jeep patriot 2009, diagram?


Go to this site and go through the menu of your vehicle to the last page and there look for a link to "Routing" that will be a picture of your belt's routing around the pulleys. Dayco hope this helps FixYa up.

Sep 07, 2011 | 2009 Jeep Patriot

1 Answer

Remove & replace window cranks---- Jeep patriot 2009


you need to use a window crank removing tool and remove handle. Make sure window is all the way up before reinstalling handle on splines.

Mar 05, 2010 | 2009 Jeep Patriot

1 Answer

Amateur radio installation in 2009 jeep patriot


To run any wire through the firewall, find a spot that is both reachable and unobstructed on both sides of the wall. I generally use a very short bit so after penetrating, it does not accidentally plunge into other wiring or components, or I use a collar over the bit (a small piece of tubing, leaving only 1/4" of bit exposed) I sometimes also "cheat" by poking a hole in the rubber boot where the steering column goes through.
Whenever passing a wire through sheet metal you must install a grommet. (if none are available, you can make one by using a piece of rubber tubing or the cut off end of an old tire valve.)
When tapping power from the battery, you will need to use a relay and switch attached to the "accessory on" side of the ignition switch, to prevent whatever you are installing from remaining on after the vehicle has been turned off. Use fuses in all new power sources as well to protect the vehicle and your new install from damage.
In creating a new circuit, you have the opportunity to use shielded wire, which will prevent stray electrical "noise" in your set" not a bad idea to do that.
good luck

Oct 18, 2009 | 2009 Jeep Patriot

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

58 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

75117 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7772 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...