Question about 2002 Nissan Maxima

1 Answer

Bypass security .Normally if I turn the key ON position to the Ignition the security Red Light is purposed to blink not to stay permit on the security bob Light.

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    New Friend:

    An expert that has 1 follower.

    Cheetah:

    An expert who has answered 20 or more questions within one hour.

  • Expert
  • 67 Answers

Repost your issue not sure what your asking

Posted on Dec 25, 2013

Ad

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
MECP Guy
  • 344 Answers

SOURCE: want to bypass stock security system or key is

ground the green with yellow wire in the drivers door harness

Posted on Mar 06, 2010

  • 1 Answer

SOURCE: Non starting Terrano

i havent had solution yet mate will keep u posted

Posted on Jan 27, 2013

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

My Cadillac cts 04 won't start... Every time I turn the key it won't even turn over... But the light that shows a car with a lock on it blinks what do I do


Sounds like the anti theft system is active m try this process. Turn the key on. Do not attempt to start. Wait 10 minutes. Turn key off. Turn key on. Wit for theft light to go off. Now attempt to start.

Oct 25, 2016 | Cadillac Cars & Trucks

1 Answer

My 1999 aruora secrity light is blinking and my car wont start. If it does it only runs for bout 3 sec then dies again . Thats only when its been sitting for a couple day . Nobofy can figure out whats...


Sounds like a problem with the security. It immobilizes the fuel injector circuit when the security is on.

Try this: turn key to on, and wait several minutes (up to 30 minutes) to see if light stops blinking. If it does stop, turn key back off, then try to start it. If the security light goes off, it may have reset. If it does not stop blinking or staying on steady, the dealer will charge outrageous prices to fix it-possibly over $800. Google "passlock bypass" or "passkey bypass" or "VATS bypass" to see your options. A site called newrockies sells a module (about $200) that forever bypasses the whole security system.

Oct 01, 2014 | 1999 Oldsmobile Aurora

2 Answers

When security light turn on start blinking car don't start.


You have an issue with your security system. There is a simple security bypass article online for this vehicle.

Sep 28, 2014 | 2004 Pontiac Grand Am

2 Answers

Security light is blinking and car won't start just replaced the fuel pump car will start for a couple secounds and dies


you need your manual it tells how to reset security system or give dealer a call they should tell you

Jun 20, 2014 | 2001 Pontiac Grand Am SE

1 Answer

2001 mitsubishi eclispse gs wont start how do you bypass the security system


  • 1 Turn the ignition key counter clockwise in the driver's side door to unlock the caricon1.png. This deactivates the alarm long enough for you to gain access to the vehicle. Then, place the key in the ignition and turn the key until it clicks once. This starts the car's battery, but doesn't ignite the engine. The LED light on the dashboard should stop blinking, indicating the alarm is temporarily disabled.
  • 2 Locateicon1.png the box for the alarm under the dashboard on the driver's side of the car. Then, look for the override button on the box. Typically, the small button is either red or black. With the ignition key in the "on" position, press the override button and hold it in until the alarm chirps once. This disables the alarm until you manually reactivate it.
  • 3 To reactivate the alarm, turn the key to the "on" position and press the override button once. The alarm chirps twice, indicating the alarm is active.

  • Hope this helps!

    Mar 15, 2014 | 2001 Mitsubishi Eclipse

    1 Answer

    Security light stays on how do you get it to turn off


    put your key in ignition, turn to "run" position and leave it sit there for about ten minutes or so, then shut it off and try to start it. Should work ok then but it's going to do it again. That security system CAN be bypassed if you find the right technician.

    Nov 05, 2013 | 1998 Pontiac Sunfire

    1 Answer

    2004 Alero. Car turns over, but won't start. Security light blinks.


    Hey jonce17....I had the same problem, and my Alero sat in my driveway for 2 days. I looked online for the solution, and I found out how to bypass the security. After it won't start and the security light is blinking, turn the ignition to the on position. Leave it there till the security light stops blinking and stays on (usually takes 9 to 10 minutes). Then turn ignition to off position and start it like normal. This happens to me about once every couple of months. Hope this helps....

    Nov 07, 2010 | 2004 Oldsmobile Alero

    3 Answers

    Dont know how to reset or bypass gm theft system car is not starting .It tries and quits.


    this is one way to reset it :
    first make sure the battery is fully charged , then do the following:
    key in the ignition but do not crank the motor, just leave it at the
    ignition mode for ten minutes ,then turn it off POSITION for 5 seconds then REPEAT again 2 more times. at the 3 rd time youre gonna notice the ANTI THEFT light on dash to blink. when doing the last step , remove key , inserted again and turn on motor , good luck , AJ

    May 28, 2009 | 2001 Chevrolet Malibu

    1 Answer

    How do I program my key for my 2006 Chevy Impala?


    Add Duplicate Key (PK3 or PK3+ key)
    1. Insert an existing key into the ignition cylinder.
    2. Turn the ignition cylinder to ON (RUN) and back to OFF.
    3. Remove the existing key and, within fifteen seconds, insert the new key
    and turn it to ON (RUN).
    4. The security light will light up for two seconds to indicate success in programming
    the key into the vehicle.
    Originate New Master Key (PK3 or PK3+ key)

    1. Insert new key into ignition cylinder and turn it to the ON (RUN) position.
    The security light on the dash will illuminate and stay on for ten minutes.
    2. When the security light goes out, you have one minute to start the next
    step. Turn the ignition cylinder to OFF and then back to the ON (RUN)
    position. The security light on the dash will illuminate and stay on for ten
    more minutes.
    3. When the security light goes out, you have one minute to start the next
    step. Turn the ignition cylinder to OFF and then back on the ON (RUN)
    position. The security light on the dash will illuminate and stay on for ten
    more minutes.
    4. After the security light has gone off the third time, the key has been programmed
    into the vehicle’s computer and will operate the car. It has replaced ALL the
    previous electronic key codes and is the ONLY key programmed into the
    vehicle’s computer.

    Add Duplicate Key (PK3 or PK3+ key)

    1. Insert an existing key into the ignition cylinder.
    2. Turn the ignition cylinder to ON (RUN) and back to OFF.
    3. Remove the existing key and, within fifteen seconds, insert the new key
    and turn it to ON (RUN).
    4. The security light will light up for two seconds to indicate success in programming
    the key into the vehicle.

    May 20, 2009 | 2006 Chevrolet Impala

    3 Answers

    How do i bypass security on 98 gmc jimmy 4.3


    I experienced this problem, intermittant failure to start. This procedure must be done with the truck RUNNING.

    Remove the cover off of your ignition switch. On the top there is a small wire connector that, once the truck is running, should be disconnected. This will turn on the 'SECURITY' light. All will be better, except the security light will be on at all times, much cheaper than replacing the ignition switch, however.

    Apr 24, 2009 | 1998 GMC Jimmy

    Not finding what you are looking for?
    2002 Nissan Maxima Logo

    86 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Nissan Experts

    yadayada
    yadayada

    Level 3 Expert

    76691 Answers

    Phil Lovisek
    Phil Lovisek

    Level 3 Expert

    726 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22219 Answers

    Are you a Nissan Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...