Question about Saab 9

1 Answer

Need torque settings for mazda xa 3.0l diesel 4 cyl

Require torque settings for mazda 3.0l diesel 4 cylinder , it is ou of a oldish mazda triton truck non turbo can some one please help me ive been trying to find settings for a while now thanks

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Saab Master
  • 45,644 Answers

Con rod bolt tension is 55-60ft/lbs
crank shaft main bearings is 80-85 ft/lbs
fly wheel bolts95-100 ft/lbs
crank shaft pulley nut 94-123 ft/lb
head studs tension 80-95 ft/lbs working in a spiral direction from no 1 stud directly in the centre of the head. Pull down in 10ft/lb increment starting at 20 ft/lbs
valve clearance is .010" both valves cold but after warming engine and re-tensioning the head studs re set valves to .012 both valves
injector retaining nuts tension12-17 ft/lbs

Posted on Dec 25, 2013

Ad

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
Saaboheme
  • 76 Answers

SOURCE: 1993 saab 900 belt diagram

Sorry, I don't have access to a Bentley now. There are 4 belts, 2 for alternator etc, 1 for aircon and 1 for pwr steering.
The power steering belt goes round the power steering pump & crank pulley only.
The paired belts go round crank pulley, alternator and water pump.
The aircon belt goes round crank pulley, aircon compressor and tensioner.
Alternator / water pump pair are closest to the engine.
Power steering is in the middle (with aircon) or closest to the bulkhead (without aircon).
Aircon (if fitted) is closest to the bulkhead.

(1) If you do not have an AC compressor, skip this step and go to step 2. If you dohave one, begin by cutting any cable ties that hold the main wiringharness to the AC hoses. Lift the harness up and over onto the camcover until it's near the PCV valve, and is now out of your way.

All nuts & bolts in this step are 13 mm.

Then, slacken the 2 bolts attaching the AC tensioner pulley mount (athick triangular steel plate) to the head. Use a long box wrench (ringspanner, in Englishicon_cheesygrin.gif ).

Using a deep-wall socket (or an offset ratchet wrench, or plain wrench)on the adjuster nut, back it off until there's no more tension in thebelt (you won't be able to remove the belt yet, though).

Now, remove the upper of the 2 mounting bolts and its washer, and pivot the tensioner down; remove the belt.

Remove the lower bolt, and lift out the tensioner. Look the triangularplate over for cracks, and spin the pulley to see if its bearing issmooth and quiet. (If you find problems, the pulley is about $15 and www.eeuroparts.com sells the entiretensioner assembly for something like $70.) Back off the adjuster nutuntil it's about 1/4" (1/2 cm) from the end of its threaded rod (usevise-grips to clamp the rod's other end onto the triangular plate, orput the whole thing in a vise).

(2) Slacken the bolt and nut holding the power steering pump to thehead and to the RH engine mount, respectively. Slacken the adjuster nut(yes, anotherthreaded-rod type thing) by about 1/2" (1 cm). You can use a normalwrench for this, but it takes forever--so I made a special tool bytaking a cheapo 13 mm open-jaw wrench and bending it to a 45-degreeangle just below the jaws (cut it to length if it's too hard tomaneuver). Loosen the mounting nut until it's almost off (but not completely off,or you'll lose the bolt it screws onto--this bolt was designed to fallout when the nut is removed). Pull the nut end of the threaded rodtowards the firewall to get it of the adjuster fork. Push the pumptowards the engine centerline and pull its belt off (you may need topry with a screwdriver to get it out of the pump pulley completely).

(3) Slacken the 16 mm nut on top of the alternator. Back off the alt.adjuster's 10 mm nut about 1/2" (1 cm)--a ratcheting wrench helps here.(This is the last threaded rod--I promise.) Completely remove the 16 mmnut, and pull the adjuster towards the firewall until it's out of thealt.

Now for the clever part: Cut yourself a wedge from a piece of wood (2 x4 is perfect), with a rise of 3" (8 cm) and a run of about 12" (30 cm).Push the alt. towards the engine, and shove the wedge in between theside of the alt. and the coil-spring tower (master cylinder mountingbracket works, too). Keep pushing the alt. and driving the wedge downuntil the alt. is so close to the engine that it's compressing thelower heater hose.

Pull the outer belt off the alt. pulley. Working from the RH side ofthe car, lift the belt off the water pump pulley and then disengage itfrom the crank pulley. Now, pull the inner belt into the outergroove of the water pump pulley. Go back to the LH side of the car, andmove the inner belt into the alt. pulley's outer groove. Try removingit from this pulley; if too difficult, either wedge the alt. closer tothe engine or try pulling the belt off the water pump pulley from theRH side of the car (a helper is very useful for all this).

(4) Install the new inner belt by fitting it into its groove in thecrank pulley first. Work it into the outer grooves of the alt. andwater pump pulleys, then into the inner ones. Install the outerbelt--again, first onto the crank pulley, then the water pump and alt.pulleys.

Remove wedge. Insert tensioner into alt. making sure the threaded rodsettles into its fork, and refit its 16 mm nut--but don't fully tightenit yet. Tighten 10 mm adjuster nut until belts can be pushed in only1/2" (1 cm) by thumb pressure (applied 1/2 way between water pump andcrank pulleys).

(5) Push PS pump as close to engine centerline as possible, andfinger-tighten its mounting bolt to hold it there. Fit a new beltaround the crank pulley first, then work it into the pump pulley groovefrom the bottom of the pulley until it pops in. You may need to use both hands, and/or carefully pry the belt on with a screwdriver.

Loosen the bolt you just tightened. Pull the pump away from enginecenterline, insert threaded rod into its fork (you may have to back theadjuster nut off some more), tighten the mounting nut (but notcompletely), and screw in the adjuster nut until the belt deflects asdescribed in (4) above.

(6) Start the engine. Blip throttle, watching the belts deflect as theengine speed goes up and down. If the "blur" you see midway down eachbelt is over 1" (2 cm) wide, tighten the belt(s) until it isn't. Tighten the PS pump mounting nut and bolt, and the 16mm nut on the alt.

If your car doesn't have AC, your belt replacement is over!

(7) If you haveAC, reattach the tensioner to the head with the lower bolt only (andleave this bolt finger-tight). Fit the new belt around the crankpulley, then around the compressor pulley and, finally, around thetensioner.

Reinstall the top tensioner bolt and its washer. Be careful and patienthere--you're threading a steel bolt into aluminum, so make sure it goesin straight. You may have to back off the tensioner nut a little. Leavethis bolt finger-tight.

Screw in the adjuster nut to get the deflection as described in (4)above. Start the engine, and blip the throttle. Watch belt's "blur" on LHside of engine. Adjust as in (6). Switch on compressor, and repeat.

If satisfied, tighten the 2 tensioner bolts. Return wiring harness toits original position, and re-secure with cable ties if needed.

Posted on Dec 16, 2008

inspectmycar
  • 233 Answers

SOURCE: 94 mazda B3000 3.0L cylinder head torque specs

Step 1 torque to 59 ft pounds
2. Loosen one full turn
3. 37 ft pounds
4. 68 ft pounds

Use torque sequence below
aca9f77.gif

Posted on Sep 17, 2009

  • 10 Answers

SOURCE: I need a workshop manual for a 2007 Mazda bt50,

http://www.filekeeper.org/download/bt50/MAZDA%20material%20for%20technician/BT-50_en.pdf

Training manual...just as good!

Posted on Oct 07, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What is cylinder head bolt torque?


you didn`t have this info in you earlier question. not sure what they are but I believe you torque the bolts first then its torque to yield. meaning they are torqued by degrees of turn. like turn bolt 75*.

Aug 11, 2015 | 2012 Mazda 6 i Sport Sedan 2.5L 4-cyl....

1 Answer

How do I set tappets of a 2.5 diesel turbo mazda


you haven't mentioned if it is a 4 cyl or not. However bring no 1 cylinder up to tdc and watch the tappets of the next cylinder to fire. when that cylinders rockers are in valve overlap situation ( exhaust starting to close and inlet starting to open) then that will be maximum clearance on no 1 cylinder and is when you set the tappets turning the engine until the next cylinder is at TDC watch for the next cylinder again to be in valve overlap and repeat as for no 1 cylinder

Dec 25, 2014 | Mazda Cars & Trucks

1 Answer

Engine torque specs


contact parts store or dealer service,

Dec 25, 2013 | Cars & Trucks

1 Answer

Cant find torque settings for a mazda XA 3.0L 4 cylider


older mazda diesels e3000 (3litre) were often rebadged to ford traders I have a book on that diesel (E3000)and if it is the same I can give you the specs but to find you again I will require you to send a reply comment. It may take me some time to dig up the book so if you will reply comment I will send you what I have

Dec 25, 2013 | Mazda B-Series Truck Cars & Trucks

1 Answer

Help with torque setting for mazda b2500 wl diesel engine


What is de torque for wl 2500 mazda main bering. Thanks

Mar 25, 2013 | Cars & Trucks

1 Answer

Has anyone put a v8 diesel engine in a triton


you will need to replace the entire drivetrain when going from a gas to diesel because of the larger engine and extra torque.

Jun 12, 2012 | Mitsubishi Cars & Trucks

2 Answers

Please describe cylinder head torque secuense mazda wl DIESEL 2007 turbo 2.5


The head torquing sequence is as below:-

9....5....1....3....7
Front
10...6....2....4....8

Carry out the sequence at least three times, once at about half the torque value and then at least twice at the full value.

Feb 14, 2011 | Mazda B-Series Truck Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

622 people viewed this question

Ask a Question

Usually answered in minutes!

Top Saab Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

yadayada
yadayada

Level 3 Expert

76848 Answers

rgbypoet

Level 2 Expert

166 Answers

Are you a Saab Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...