Question about 2006 Chevrolet Colorado

1 Answer

Pinion nut torque spec chev

Need torque spec on rear end pinion nut for a 2006 chevrolet colorado? hope you can help

Posted by on

  • Anonymous Mar 17, 2014

    pinion nut torque

×

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Contributor
  • 22 Answers

Axle Preload and Backlash Specifications 8.0 Axle Preload and Backlash Specifications Application
Specification
Metric
English
Backlash
0.08-0.25 mm
0.003-0.010 in
Backlash (Preferred)
0.13-0.18 mm
0.005-0.007 in
Pinion Bearing Preload, New Bearings
1.7-3.4 N·m
15-30 lb in
Pinion Bearing Preload, Used Bearings
1.1-2.3 N·m
10-20 lb in
Pinion and Differential Case Bearing Preload, New Bearings
3.4-6.2 N·m
30-55 lb in
Pinion and Differential Case Bearing Preload, Used Bearings
2.8-5.1 N·m
25-45 lb in

Posted on May 20, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What is torque spec for 1964 Riviera rear axle pinion nut?


The same book that I hope you used in setting the ring and pinion backlash will give you the ( Rolling Torque). Once the pinion nut is set, a new crush sleeve will be required to correct. This axel will not go around the block if back lash is not correct.

May 10, 2017 | Cars & Trucks

1 Answer

What is the torque specification for the pinion nut and 1960 Chevy Impala


We are talking rear end hear correct . However torque isn't spicific to vehicles what it is spicific to is the grade of the metal V S the treard pitch V S the size of the shaft and nut .Most poinion nuts are what is called flange nuts witch means there is a base on the nut and you need 2 differant wrenches to install or remove one to hold one side and the other to break it free on tighten .The problem here is its hard to know with a torque wrench on the nut and an open end wrench on the pinion side . So take to big open ended wrenches and crank them together as tight as you can . this gives you x2 torque but the spec about 65 ftlbs to 90 lbs for most although you will not be able to measure acuralty

Mar 17, 2015 | Chevrolet Impala Cars & Trucks

2 Answers

What's the torque on the rear yoke center nut on a 2005 colorado


Yoke torque is 400 foot pounds. to crush the crush washer to seat the bearings,,, after the crush washer is seated i believe it 100 foot pounds,,use a little red lock tight if its a used nut,,,setting up a rearend is a complecated and time comsuming deal,,need many specilized tools,,,easyer to replace whole rearend from salvage yard cost about the same

Feb 18, 2015 | 2005 Chevrolet Colorado

1 Answer

What is the torque spec for a 1978 Ford pinto differential pinion nut?


170 ft.lbs is the minimum; be aware that this differential uses a crush sleeve to set the backlash and the pinion torque is what crushes the crush sleeve. If you don't set the backlash correctly you can grind up your differential gears.
8 Inch Ford Rear End Torque Specifications eHow

Feb 02, 2015 | Ford Cars & Trucks

1 Answer

I need the torque specs on a rear axle pinion nut for a 2003 Dodge Ram 2500 4/4 Cummins, Automatic.


The pinion nut does not have a torque spec. as in how tight the nut is. The amount of torque is measured in bearing preload. You will need a "torque to rotate" torque wrench. If you are using new bearings the torque spec. is 15-25 in. lbs. If you are using your old bearings the torque spec. is 10-20 in. lbs to rotate. To measure this you will need to tighten the nut in small increments then use the torque to rotate wrench to turn the pinion without the carrier/ ring gear installed. Repeat until desired torque is reached.

Jan 29, 2011 | Dodge Ram 2500 Cars & Trucks

1 Answer

What is the torque on pinion nut for a 2002 1500 silverado with a rebuilt rear end?


HI, If you have a gmc axel pinion seal nut torque is 270 FT.LBS or 366 NM
If you have a dana axel pinion seal nut torque is 255 FT.LBS or 346 NM
If i can help you anymore just re post
Thanks dodge tec

Jan 02, 2011 | 2002 Chevrolet Silverado 1500

1 Answer

What is the pinion nut torque when installing new bearings and crush sleeve


i am not aware of a specific torque spec , you have to crush the sleeve until the end play of the pinion measured with a dial indicator matches the proper spec wich should have come with the installation guide

Aug 10, 2010 | 1996 Chevrolet S-10 Pickup

1 Answer

Replaced rear axle pinion bearing and seal, need to know pinion nut torque spec. for aam rear axle 2005 dodge 3500 4x4 Thanks.


There is no torque specs,this nut has to be tightened back like it was ,the best thing to do,was,to late now,is to use a torque wrench to remove the nut,and remember the torque,and when replacing it,torque it back to that spec,the reason being,there is a crush sleeve between the front pion bearing ,and the rear pinion bearing,and it has to be crushed to a certain amount,to aquire deepness into the ring gear,anyway just give it about 25 lbs torque,any more the crush sleeve will crush even more and the deepness of the pinion will be too much.

Apr 19, 2010 | 2005 Dodge Ram

1 Answer

Need torque specs for the pinion nuton rearend!!!!!!


If your car is a rear wheel drive, and you mean the nut that's just after your drive shaft, then...If you are replacing the seal, you need to mark the nut and the shaft so that when you re-assemble it you tighten the nut just a 1/4 " past the original mark. The reason is there is a crush collar that compresses inside on your pinion shaft to give it a little resistance. This is measured using a beam type inch pound torque wrench. I hope this might answer some questions. Setting up a pinion once removed requires a new crush collar, and the inch pounds of resistance are a little different between new bearings, or if you reuse the old ones.

Jul 10, 2009 | 2000 Chevrolet Camaro

1 Answer

2005 chevy 4x42500hd


Hi..
On your 05 Chevy 4X4 2500HD.
The Pinion Yoke Nut, 9.75" Axle. the torq spec. is 370 Nm. -- 273 Lb ft.

I hope this help on your question.

Thank you for use fixya...

Nov 04, 2008 | 2008 Chevrolet Silverado 2500HD 2WD

Not finding what you are looking for?
2006 Chevrolet Colorado Logo

918 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6918 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...