Question about Cars & Trucks

Open Question

Chevy colorado bogs

My 06 chevy Colorado 4 cyl bogs down in reverse when you come to a stop why is this?

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 67 Answers

SOURCE: engin light is on

the check engine light can come on for any number of reasons mostly emissions related problems. the first step is to identify the code responsible for the light. there are many auto parts stores that will scan the vehicle free of charge for you. i suggest that first.

Posted on Dec 08, 2008

Ad
  • 1 Answer

SOURCE: Rough idle

I had the same exact problem on my 2004 Colorado (3.5L). Cleaned the MAF sensor (with MAF sensor cleaner) and throttle body/plate - cleared it right up.

Posted on Aug 24, 2009

c17hydro
  • 2984 Answers

SOURCE: how do i change out the knock sensor on a 2006 chevy colorado

You didn't list your engine size so please pick the applicable to your motor size:

Removal & Installation 2.8L & 2.9L Engines To Remove:

  1. Lift the vehicle high enough to gain access to the knock sensor (KS) through the left front wheelhouse.
  2. Remove the left front wheel and wheelhouse liner.
Knock sensor (KS) (A), Engine harness (B), Knock sensor (KS) connector (C)


e44e83f.gif
  1. Disconnect the knock sensor (KS) connector.
  2. Detach the knock sensor (KS) from the engine block.
To Install:
  1. Attach the knock sensor (KS) to the engine block.
    • Tighten the bolt to 18 ft lbs (25 Nm).
  2. Connect the knock sensor (KS) connector.
  3. Install the left front wheelhouse liner and wheel.
  4. Fully lower the vehicle.

Posted on Sep 03, 2009

  • 91 Answers

SOURCE: How to remove the car stereo from 2007 Chevy Colorado

This is not hard but tricky because the trim plate around the radio has clips that hold the trim plate very tight.Use a plastic type flat tool or flat screw driver wraped with tape or a shop rag to avoid damage to the plastic trim and pry the trim panel around the radio loose. remove all elec connectors.Then remove the screws that hold the radio in place and remove all elec connectors.

Posted on Feb 22, 2010

  • 753 Answers

SOURCE: Transmission fluid for 2005 Chevy Colorado

You would need to find something that is the same as sychromesh fluid that GM uses.

Posted on May 03, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 06 chevy colorado engine light came on


hi this could be a lot of things, the only way to find out is to have it checked with a code reader, it could be something simple like a miss fire as sometimes happens or could be something more serious best get it checked out, you could have a sensor gone u/s and you might be using allot of fuel.....hope this helps

May 10, 2010 | 2006 Chevrolet Colorado

1 Answer

Transmission fluid for 2005 Chevy Colorado


You would need to find something that is the same as sychromesh fluid that GM uses.

May 03, 2010 | 2005 Chevrolet Colorado

1 Answer

Stalls when placed in reverse


well you have convertor lock prob prob a sensor for trans let me know hey till fix ya bouy me ok

May 23, 2009 | 2005 Chevrolet Colorado

1 Answer

2005 Chevy Colorado edit


If you put the tail gate down, there is 2 screw (phillips) that holds the tail light in place. Remove them & you can twist the bulb out. Thats it, put back together in reverse. Hope this helps.

May 21, 2009 | 2005 Chevrolet Colorado

2 Answers

Rough idle


I had the same exact problem on my 2004 Colorado (3.5L). Cleaned the MAF sensor (with MAF sensor cleaner) and throttle body/plate - cleared it right up.

May 10, 2009 | 2006 Chevrolet Colorado

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

30 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...