Question about 2005 Chrysler 300

Open Question

Replace NVLD pump on 2004 Pacifica - 2005 Chrysler 300

Posted by Anonymous on

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

todd0708
  • 247 Answers

SOURCE: replace fuel pump on 2004 pacifica

you can look under the carpet above the tank,but most newer vehicles you just remove the fuel tank,usuall two bolts that hold the straps,you will need special tool for high pressure fuel line connections,about 10 or 15 bucks at your local parts store,make sure you get the one for your make of vehicle,hope this helps,aloha from maui todd0708

Posted on Oct 22, 2009

chargerhp
  • 813 Answers

SOURCE: replacing a water pump on a 2004 pacifica

Release fuel pressure.Remove neg battery cable. Drain cooling system.Remove front cover.Remove timing belt. Remove water pump. Remove timing belt tensioner and slowly compress in vice. Install water pump then install tensioner and belt. timing belt runs water pump!

Posted on Sep 09, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is Pacifica 2004 water pump is located


It is behind the cover on the passenger side of the engine. If you are going to that trouble replace the timing belt also it is behind there too
9_23_2015_8_19_02_pm.jpg

Jul 30, 2014 | 2004 Chrysler Pacifica

1 Answer

Why 2004 chrysler pacifica start up and then shut off?


theft light on? key lost programming,fuel pressure wrong after sitting (fuel pump needed)regulator on pump this only occurs after sitting will be fine if you drive shortly after just driving.

May 31, 2014 | 2004 Chrysler Pacifica

1 Answer

I have have a 2003 dodge durango and I have had a smoke test done with no leaks the mechanic said it has no power to the NVLD how do I check this


Hi Richard, I'm glad to help. The mechanic is the only one that can check power to the NVLD Pump because it must be actuated with the scan tool to check power. Check for a broken wires or a pin pust out on the NVLD connector. If you don't know what fuses to check then turn the key on and with a test light check all the fuses under the hood. If they are all good then you'll need it checked out further by a certified mechanic. If you do find a fuse blown and it turns out to be the one for the NVLD then replace the pump because its most likely the culprit that blew the fuse. Hope this helps and have an awesome day Richard.

May 07, 2014 | 2003 Dodge Durango

1 Answer

Looking for the location of the water pump on a 2004 chysler pacifica and a diagram for repalaceement


`The water pump is inside the timing cover and is run by the timing belt. If the water pump has been leaking I would also replace the timing belt and check the belt tensioner carefully.

Jul 02, 2011 | 2004 Chrysler Pacifica

1 Answer

Replacing a water pump on a 2004 pacifica


Release fuel pressure.Remove neg battery cable. Drain cooling system.Remove front cover.Remove timing belt. Remove water pump. Remove timing belt tensioner and slowly compress in vice. Install water pump then install tensioner and belt. timing belt runs water pump!

Sep 02, 2010 | 2005 Chrysler Pacifica

1 Answer

How do i replace the natural vacuum leak detection pump on a 2005 dodge dakota?


Vehicles equipped with NGC engine control modules use an NVLD pump and system. Vehicles equipped with JTEC engine control modules use a leak detection pump. Refer to Leak Detection Pump (LDP) for additional information.
The Natural Vacuum Leak Detection (NVLD) system is the next generation evaporative leak detection system that will first be used on vehicles equipped with the Next Generation Controller (NGC). This new system replaces the leak detection pump as the method of evaporative system leak detection. This is to detect a leak equivalent to a 0.020 (0.5 mm) hole. This system has the capability to detect holes of this size very dependably.


Removal & Installation
  1. Raise and support vehicle.
  2. Remove left-rear tire.
  3. Remove plastic shield (4) in front of left-rear tire. Access to both the EVAP canister (1) and NVLD pump (6) is from the area in front of the removed tire.
  4. Disconnect electrical connector at NVLD pump.
  5. Remove vapor line at NVLD pump. Pry outward on tab (3) and rotate pump (6) clockwise about 70 for removal.
  6. Remove NVLD pump O-ring (5) from EVAP canister (1).
To Install:
  1. Install new NVLD pump O-ring (5) to EVAP canister (1).
  2. Position NVLD pump (6) into EVAP canister (1).
  3. Rotate pump (6) until tab aligns with notch in EVAP canister (1).
  4. Carefully install vapor/vacuum lines to NVLD pump.
    WARNING The vapor/vacuum lines and hoses must be firmly connected. Check the vapor/vacuum lines at the NVLD pump, filter and EVAP canister purge solenoid for damage or leaks. If a leak is present, a Diagnostic Trouble Code (DTC) may be set.
  5. Connect electrical connector to pump.
  6. Install plastic shield in front of left-rear tire.
  7. Install left-rear tire.

    2e35911.jpg
    Fig.


    aa300e1.jpg
    Fig.

Have a nice day (remember rated this help).


Mar 05, 2010 | 2004 Dodge Dakota

1 Answer

How to locate and replace the natural vacuum leak detection pump on a 2004 dodge caravan ?


THE NVLD ASSEMBLY IS LOCATED UNDER THE VEHICLE ON THE METAL PLATE BOLTED TO THE FRONT ALUMINUM K FRAME..JUST BEHIND TRANS DIFFERENTIAL..HAS SOME HOSES AND AND AN ELECTRICAL CONNECTOR GOING TO IT..BLACK PLASTIC HOUSING..HOSES LEAD TO CANISTER BEHIND FRAME..DISCONNECT HOSES,ELECTRICAL..MARK THEM IF YOU NEED TO..BUT ALSO LOOK FOR A BROKEN WIRE NEAR NVLD AT CONNECTOR..UNBOLT ASSEMBLY FROM FRAME..I YOU HAD A NEW ONE YOU WILL SEE WHAT IT LOOKS LIKE..I HOPE THIS HELPS

Oct 16, 2009 | 2004 Dodge Caravan

2 Answers

Engine trouble code 0499 2004 dodge dakota manual 5 speed 4.7 4x4


P0499 Evaporative Emission System Vent Valve Control Circuit High, REPLACE THE SOLENOID.

Jun 24, 2009 | 2004 Dodge Dakota

Not finding what you are looking for?
2005 Chrysler 300 Logo

Related Topics:

32 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

75744 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8123 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...