Question about 2003 Toyota Camry

1 Answer

Installed pads on all 4 wheel . now peddle is very soft. goes to floor slowly.

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 232 Answers

You need to bleed the system ,there is alittle bit of air in the lines.

Posted on May 17, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Breaks go to the floor


Then you have a massive leak somewhere as the brake peddle should not go all the way to the floor without some low break fluid indication. I would check brakes at each wheel as something isn't right or your not seeing it. Have someone pump the pedal and look to see if after the wheel is removed that the brake actually tightens and loosens. Remember that 4 wheels means 4 brakes, but master brake cylinder (where you add brake fluid) could be bad.
tandem-master-cyl2.gif


May 06, 2014 | Pontiac Grand Prix Cars & Trucks

1 Answer

I have replaced the master cylinder and primed it. Also, I have relaced all four calipers, pads on all four tires, and I replaced all four rotors. It still will not bleed off. What else should can I do?


Try opening all 4 bleaders and using very little pressure on the peddle like very slowly to the floor an having somone watching the bleeders.once the fluid starts to drip close bleader until all 4 are done,make sure not to drain the reservoir.do not exerte pressure on the peddle.nex step reblead each wheel .if this does not work,the master is most likely defective.Good luck.

Dec 28, 2010 | 1998 Ford Explorer

2 Answers

Bleeding air out of brake line after changing brake pads,we got no air bubbles but still have a spongy or soft brake peddle


Bleed the longest line first, then progressively shorter lines. Make sure you are using the correct technique in bleeding--be sure the master cylinder is always full, then pump the pedal several times in quick succession and hold pressure while your assistant opens the bleeder valve slowly and lets it drain until your foot is to the floor. Hold your foot until the bleeder is again closed, then repeat the process. Don't reuse the expelled fluid. Hope this helps!

Sep 19, 2010 | 2004 Dodge Ram 3500 Truck

1 Answer

1994 gmc Sierra. Poor, soft, spongey peddle feel


well maybe the lines are not bleed right. did you bleed the master??

May 09, 2010 | 1999 Chevrolet Silverado 1500

2 Answers

NO BRAKES, Peddle goes to the floor


there is air trapped in the portion valve read up on this autozone .com might have this in there repair manual if not usually ford has a electronic scan tool for this to reset it

Aug 16, 2009 | 1999 Ford Expedition

2 Answers

Put new roders, brake pads, and calipers on 2002 Olds Alero. The brake peddle is really soft and goes almost all the way to the floor....Why is this? Car has 26,000 on it..


groan......master cylinder not brakes and rotors and what not. hopefully you kept all of you old stuff because there was probably nothing wrong with it. also, make sure that you do a realy good job bleading you break = air will cause the pedal to go down to the floor. also if you change the master cylinder, that you try and bleed most of the air out before you install it into your vehicle

Jul 11, 2009 | 2002 Oldsmobile Alero

1 Answer

Abs brakes on 92 cavalier


did you follow a bleeding order? some cars do have an order that must be followed. does the car have abs? abs units go bad / have to bled as well and will give you the same effect. did you notice any leaks? aby shinny spots on any of the tires on the inside?

Jul 02, 2008 | 1992 Chevrolet Cavalier

Not finding what you are looking for?
2003 Toyota Camry Logo

Related Topics:

29 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7782 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...