Question about 1995 Isuzu Rodeo

1 Answer

Fusible link keeps blowing any ideas on why or what i can do to fix it

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Check you main grounds clean the area of connection

Posted on May 17, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Have a 1999 Dodge Avenger V6. Keeps blowing Engine Fuse under hood


Fusible link 3 feeds the PCM. the ASD relay, and fuel pump relay. Assuming it has A/T, that fusible link also feeds the starter relay, the EATX-ECM, and the EATX relay. A short in any of those elements could be causing the trouble.

Dec 16, 2016 | 1999 Dodge Avenger

1 Answer

I purchased a 4 terminal starter solenoid. A 3 terminal was on truck. This 4 terminal solenoid includes an S and an I terminal. Is the I terminal used on a 1987 Ford Ranger 2.9 V6 4WD?


If the truck had a three terminal one on it then you would not use the (I) terminal, nor would it cause you to keep blowing your fusible link. It would cause a hard start cold because all the (I) terminal does is feed 12v directly to the coil on cranking. You have a short in the circuit that is on that fusible link. You need to get a wiring diagram and see what that circuit feeds. If the fuel pump isn't running than disconnect that circuit and see if it keeps the link from blowing. You may have to get a circuit breaker to install temporarily it to help find short. I have used a breaker and have gone directly to the fuse box and feed there to help isolate which circuit it is in. Good luck.

Jun 14, 2015 | 1987 Ford Ranger

1 Answer

1993 fusible link keeps burning up, causing no lights or start. if i put a new one in it just melts again and cuses the same problem. i replaced starter and battery cables. still melting. i realize th


try unplugging your radio and replace fuseable link if it doesnt blow your short is in your radio if it blows with radio discoonnected take light sockets out and inspect them for corrosion or direct shorts.

Apr 06, 2014 | 1997 Subaru Outback

1 Answer

Fusible link alternator keeps blowing


Not a lot to work with here, but I will say that if a fusible link continuously blows out, you have a problem that needs fixing either with a short in the wiring or a bad component being the issue. The first thing to check would be to check the "line in" voltage and amperage going to the fusible link. Work your way "upstream" ruling out components as you go using this testing method. Once you find a point in the line that has the correct input, you have found your trouble component. The component that has the correct amperage flowing into it, and the incorrect flowing out is your issue. You may also find a short in the wiring somewhere along the line which could also be the issue.

Dec 24, 2012 | 1985 Buick Century

1 Answer

I have a 1994 Honda Accord. The 40 amp fusible link keeps blowing after 30 minutes of replacement. Any suggestion?


You will have to find out what circuit or circuits that link delivers power to, then look for the short-either a stripped wire contacting metal, or a component like a failed motor that is pulling too much current.
Is it a fusible link or a maxi-fuse? Check if it could be for the alternator.

Nov 27, 2012 | 1994 Honda Accord

1 Answer

Nissan pathfinder 2009 fusible link on engine compartment keeps blowing upon replacement engine wont starts, and the dashboard (INOP)


Someone will have to check the wiring to find the short to ground.
You may need a shop manual to get the necessary diagrams.

Sep 29, 2012 | 2009 Nissan Pathfinder LE

1 Answer

No power to the radiator fans but the fan works when battery power is applied. Any idea what the problem is?


Could be a 'fusible link' near the starter. The fusible link will blow when overloaded like a fuse, but looks like a wire with a barrel of rubber around it. You can stretch the wire insulation on it when the fusible link is blown.

Also, check for power at the relay for the radiator fan.

Apparently, your fan motor works when power is applied directly.

Good luck on this repair.

Jul 07, 2010 | 2001 Chevrolet Impala

2 Answers

83 280z smoked a fusible link dont know why or how to fix ?


get a new fusible wire and solder it in place of the old one.
Vitally

Sep 10, 2009 | 1983 Nissan 280ZX

1 Answer

80a fusible link 95 4runner keeps blowing


You either have a short somewhere, or the alternator is over charging. What does the volt gauge read before it blows, if you don't have a gauge, get a volt meter and test at the battery. Anything over 14.5 will blow the link.

Jun 10, 2009 | 1986 Toyota Pickup 4WD

Not finding what you are looking for?
1995 Isuzu Rodeo Logo

Related Topics:

99 people viewed this question

Ask a Question

Usually answered in minutes!

Top Isuzu Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Steve Hurc
Steve Hurc

Level 3 Expert

450 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Are you an Isuzu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...